! P2 SE Signature ! ! STEREO POWER AMPLIFIER OWNER’S INFORMATION !
CONTENTS ! 1) IMPORTANT SAFETY INFORMATION 2) CE DECLARATION OF CONFORMITY DISPOSAL POWER REQUIREMENTS 3) INTRODUCTION 5) OVERVIEW UNPACKING AND INSTALLATION 6) CONNECTION 7) OPERATION 8) TECHNICAL SPECIFICATIONS 9) WARRANTY INFORMATION 10) CONTACT INFORMATION
! IMPORTANT SAFETY INFORMATION ! RISK OF SHOCK OR ELECTROCUTION! INTERNAL OPERATING VOLTAGES ARE LETHAL! Do not remove top cover, unless specifically instructed to do so in the user manual. This unit contains fuses and other safety components in accordance with BS60065 requirements. In the event of failure, replacement fuse or safety component must be of the same part type and value. ! SUCH REPLACEMENT MUST ONLY BE CARRIED OUT BY A QUALIFIED SERVICE TECHNICIAN.
CE DECLARATION OF CONFORMITY We declare under our sole responsibility that this product is in conformity with the following standards or standardized documents: BS EN 60065 in accordance with the regulations 73/23/EEC, 89/336/EEC (from 1 January 1997) CE 94 Peter Qvortrup, Director Audio Note (UK) Limited 25 Montefiore Road Hove East Sussex BN3 1RD United Kingdom Tel: Fax: +44 (0)1273 220 511 +44 (0)1273 731 498 ! DISPOSAL This product must not be disposed of as normal household waste.
INTRODUCTION Thank you for purchasing this Audio Note (UK) product. With the correct care it should give you many years of pleasure and enjoyment. Please take the time to read all of the information in this manual before connecting your new component to an electrical supply or your system, to ensure both your safety and satisfaction. Please note that due to our desire to continually improve products, specifications are subject to change without notice.
P2 SE SIGNATURE STEREO POWER AMPLIFIER Congratulations on your purchase of the Audio Note (UK) P2 SE Signature stereo power amplifier. It is a Pure Class A, Single Ended valve design, which preserves the entire musical waveform as one ‘whole’, producing a level of performance that is radically superior to the majority of current designs. Part selection is optimized to realize the most neutral and realistic sonic reproduction.
UNPACKING AND INSTALLATION Please take care when unpacking your P2 SE Signature stereo power amplifier. Choose a clean, clear location to unpack your unit. Be aware that the amplifier is quite heavy; before attempting to unpack or lift the unit, check the weight and if necessary use more than one person so that it can be moved safely and easily. We recommend that you retain and carefully store all of the original packing materials, in case transportation / shipping is required at a later date.
CONNECTION Line inputs Being a stereo power amplifier, the P2 SE Signature is fitted with one pair of single ended / RCA inputs. Looking from behind the amplifier, they are located at bottom / right hand side of the rear panel. The Black socket is for the Left channel, the Red socket is for the Right channel. Connect the output from your preamplifier to these inputs. Speakers Each channel is equipped with 3 colour coded binding posts for connection to your speakers, located on the rear panel.
OPERATION Once all the connections are completed and checked, ensure that the volume control of your preamplifier / source is at the minimum setting. Turn on all components in the signal chain BEFORE the P2 SE Signature; it should always be the LAST component to be switched ON, and the FIRST to be switched OFF. Turn on the amplifier by using the rotary switch located on the right of the front panel. The red front panel light should now be lit.
TECHNICAL SPECIFICATIONS INPUT IMPEDANCE 100 KOhm Line Level INPUT SENSITIVITY 430mV for full output MAXIMUM OUTPUT 18 watts RMS per channel into 4 or 8 Ohm loads CHANNEL BALANCE +/- 0.3dB TUBE COMPLIMENT 2 x 6SL7 4 x 5881 / 6L6WGB FUSE RATINGS 2A anti-surge (110 / 120V supply) 1.2A anti-surge (220 / 240V supply) MAX.
WARRANTY INFORMATION Audio Note (UK) warrants this product to be free from defects in materials and workmanship for two years from the original date of purchase from an appointed Audio Note (UK) dealer, and agrees to cover the cost of parts and associated labour required to correct such defects, subject to terms & conditions. This Warranty is offered to the first purchaser only. Any valves supplied with the unit are warranted for three months from the original date of purchase.
the serial number has been removed, defaced or tampered with. CONTACT INFORMATION If in the future your Audio Note (UK) product requires servicing, or if you require technical support or have any questions regarding this or any of our other products, please contact your local Audio Note (UK) dealer.
