! OTO Phono ! ! INTEGRATED AMPLIFIER OWNERʼS INFORMATION !
CONTENTS ! 1) IMPORTANT SAFETY INFORMATION 2) CE DECLARATION OF CONFORMITY DISPOSAL POWER REQUIREMENTS 3) INTRODUCTION 4) OVERVIEW UNPACKING AND INSTALLATION 5) CONNECTION 6) OPERATION 7) TECHNICAL SPECIFICATIONS 8) WARRANTY INFORMATION 9) CONTACT INFORMATION
! IMPORTANT SAFETY INFORMATION ! RISK OF SHOCK OR ELECTROCUTION! INTERNAL OPERATING VOLTAGES ARE LETHAL! Do not remove top cover, unless specifically instructed to do so in the user manual. This unit contains fuses and other safety components in accordance with BS60065 requirements. In the event of failure, replacement fuse or safety component must be of the same part type and value. ! SUCH REPLACEMENT MUST ONLY BE CARRIED OUT BY A QUALIFIED SERVICE TECHNICIAN.
CE DECLARATION OF CONFORMITY We declare under our sole responsibility that this product is in conformity with the following standards or standardized documents: BS EN 60065 in accordance with the regulations 73/23/EEC, 89/336/EEC (from 1 January 1997) CE 94 Peter Qvortrup, Director Audio Note (UK) Limited 25 Montefiore Road Hove East Sussex BN3 1RD United Kingdom Tel: Fax: +44 (0)1273 220 511 +44 (0)1273 731 498 ! DISPOSAL This product must not be disposed of as normal household waste.
INTRODUCTION Thank you for purchasing this Audio Note (UK) product. With the correct care it should give you many years of pleasure and enjoyment. Please take the time to read all of the information in this manual before connecting your new component to an electrical supply or your system, to ensure both your safety and satisfaction. Please note that due to our desire to continually improve products, specifications are subject to change without notice.
OTO PHONO INTEGRATED Congratulations on your purchase of the Audio Note (UK) OTO Phono Integrated Amplifier. It is a Push Pull, Pure Class A valve design, offering an outstanding level of performance and value.
CONNECTION Phono input The OTO Phono is equipped with a high quality, valve, Moving Magnet (MM) phonostage. Connect the cables from your tonearm to the ʻPhonoʼ socket inputs. If your Turn Table is equipped with a separate earth wire, connect this to the dedicated grounding / earth post, located next to the ʻPhonoʼ input sockets. If you wish to use a low output Moving Coil (MC) cartridge, Audio Note manufactures a series of Step Up Transformers for this purpose.
OPERATION Once all the connections are completed and checked, ensure that the volume control is at the minimum setting (rotated all the way left). Turn on the amplifier by using the rocker switch located on the rear panel, above the IEC mains inlet socket. The red front panel light should now be lit. The amplifier requires approximately 45 seconds to initialize before it is ready for operation. Input Selector Turn the selector to the source you wish to listen to.
TECHNICAL SPECIFICATIONS INPUT IMPEDANCE 100k Ohm 47k Ohm Line Level Phono Input INPUT SENSITIVITY 300mV 3mV Line Level Phono Input MAXIMUM OUTPUT 12 watts RMS per channel into 4 or 8 Ohm loads CHANNEL BALANCE +/- 0.
WARRANTY INFORMATION Audio Note (UK) warrants this product to be free from defects in materials and workmanship for two years from the original date of purchase from an appointed Audio Note (UK) dealer, and agrees to covers the cost of parts and associated labour required to correct such defects, subject to terms & conditions. This Warranty is offered to the first purchaser only. Any valves supplied with the unit are warranted for three months from the original date of purchase.
CONTACT INFORMATION If in the future your Audio Note (UK) product requires servicing, or if you require technical support or have any questions regarding this or any of our other products, please contact your local Audio Note (UK) dealer. Alternatively, please feel free to contact us directly: -! Audio Note (UK) Limited 25 Montefiore Road Hove East Sussex BN3 1RD United Kingdom Tel: +44 (0)1273 220 511 Fax: +44 (0)1273 731 498 e-mail: info@audionote.co.
