! MEISHU Line ! ! INTEGRATED AMPLIFIER OWNER’S INFORMATION !
CONTENTS ! 1) IMPORTANT SAFETY INFORMATION 2) CE DECLARATION OF CONFORMITY DISPOSAL POWER REQUIREMENTS 3) INTRODUCTION 4) OVERVIEW UNPACKING AND INSTALLATION 5) VALVE INSTALLATION 6) CONNECTION 7) OPERATION 8) TECHNICAL SPECIFICATIONS 9) WARRANTY INFORMATION 10) CONTACT INFORMATION
! IMPORTANT SAFETY INFORMATION ! RISK OF SHOCK OR ELECTROCUTION! INTERNAL OPERATING VOLTAGES ARE LETHAL! Do not remove top cover, unless specifically instructed to do so in the user manual. This unit contains fuses and other safety components in accordance with BS60065 requirements. In the event of failure, replacement fuse or safety component must be of the same part type and value. ! SUCH REPLACEMENT MUST ONLY BE CARRIED OUT BY A QUALIFIED SERVICE TECHNICIAN.
CE DECLARATION OF CONFORMITY We declare under our sole responsibility that this product is in conformity with the following standards or standardized documents: BS EN 60065 in accordance with the regulations 73/23/EEC, 89/336/EEC (from 1 January 1997) CE 94 Peter Qvortrup, Director Audio Note (UK) Limited 25 Montefiore Road Hove East Sussex BN3 1RD United Kingdom Tel: Fax: +44 (0)1273 220 511 +44 (0)1273 731 498 ! DISPOSAL This product must not be disposed of as normal household waste.
INTRODUCTION Thank you for purchasing this Audio Note (UK) product. With the correct care it should give you many years of pleasure and enjoyment. Please take the time to read all of the information in this manual before connecting your new component to an electrical supply or your system, to ensure both your safety and satisfaction. Please note that due to our desire to continually improve products, specifications are subject to change without notice.
MEISHU LINE INTEGRATED Congratulations on your purchase of the Audio Note (UK) Meishu Line Integrated Amplifier. It is a Pure Class A Singled Ended valve amplifier that uses the highly regarded 300B direct heated triode valve, producing a level of performance that is radically superior to the vast majority of current designs.
VALVE INSTALLATION The amplifier is shipped without the 3 large valves installed. It is necessary to install the valves first. It is essential that the valves are installed correctly or serious damage that is not covered by the warranty will result. We recommend that your dealer perform this procedure for you if you are in any way unsure. FIRSTLY, ENSURE THAT THE AMPLIFIER IS NOT CONNECTED TO A MAINS ELECTRICAL SUPPLY, AND THAT THE POWER CORD IS NOT CONNECTED TO THE AMPLIFIER. Using a No.
VALVE INSTALLATION Continued… Inspect a 300B valve base and you will notice that two of the pins are larger than the other two; this is to help ensure that the valve can only be inserted one way. The larger pins must face each other when each valve is inserted into the appropriate valve base on the central board. With gentle but firm pressure insert the valve into its socket. Check again that both valves are fully inserted correctly in to their respective valve sockets.
CONNECTION Line inputs Five line level inputs are available for connection to CD1, CD2, Aux, Tuner and Tape In. Connect the ‘Line Out’ sockets of your Recording device to the ‘Tape In’ sockets of the Meishu, and the ‘Tape-Out’ sockets on the Meishu to the ‘Line In’ sockets of your Recording device. Ground Post A ground post is provided for connection to those source components that also use a separate ground terminal.
OPERATION Once all the connections are completed and checked, ensure that the volume control is at the minimum setting (rotated all the way left). Turn on the amplifier by using the rocker switch located on the rear top right of the back panel, just above mains inlet socket. The red front panel light should now be lit. The amplifier requires approximately two minutes to initialize before it is ready for operation.
TECHNICAL SPECIFICATIONS INPUT IMPEDANCE 100k ohm, line level INPUT SENSITIVITY 450mV for full output MAXIMUM OUTPUT 8 watts RMS per channel into 4 or 8 Ohm loads CHANNEL BALANCE +/- 0.3dB VALVE COMPLIMENT 1 x 5U4G 2 x 300B 2 x 6X5 2 x 5687 1 x 6SN7 27.5KG UNIT WEIGHT 40KG SHIPPING WEIGHT (ORIGINAL PACKAGING) 220mm (h) x 460mm (w) x 530mm (d) UNIT DIMENSIONS 420mm (h) x 650mm (w) x 670mm (d) SHIPPING DIMENSIONS (ORIGINAL PACKAGING) MAINS INPUT AC 100-120V/220-240V 50/60 Hz MAINS FUSE 3.
WARRANTY INFORMATION Audio Note (UK) warrants this product to be free from defects in materials and workmanship for two years from the original date of purchase from an appointed Audio Note (UK) dealer, and agrees to cover the cost of parts and associated labour required to correct such defects, subject to terms & conditions. This Warranty is offered to the first purchaser only. Any valves supplied with the unit are warranted for three months from the original date of purchase.
CONTACT INFORMATION If in the future your Audio Note (UK) product requires servicing, or if you require technical support or have any questions regarding this or any of our other products, please contact your local Audio Note (UK) dealer. Alternatively, please feel free to contact us directly: -! Audio Note (UK) Limited 25 Montefiore Road Hove East Sussex BN3 1RD United Kingdom Tel: +44 (0)1273 220 511 Fax: +44 (0)1273 731 498 e-mail: info@audionote.co.
