M8 Line Signature ! ! PRE AMPLIFIER OWNER’S INFORMATION ! !
CONTENTS ! 1) IMPORTANT SAFETY INFORMATION 2) CE DECLARATION OF CONFORMITY DISPOSAL POWER REQUIREMENTS 3) INTRODUCTION 4) OVERVIEW 5) UNPACKING AND INSTALLATION 6) CONNECTION 14) OPERATION 16) TECHNICAL SPECIFICATIONS 17) WARRANTY INFORMATION 18) CONTACT INFORMATION
! IMPORTANT SAFETY INFORMATION ! RISK OF SHOCK OR ELECTROCUTION! INTERNAL OPERATING VOLTAGES ARE LETHAL! Do not remove top cover, unless specifically instructed to do so in the user manual. This unit contains fuses and other safety components in accordance with BS60065 requirements. In the event of failure, replacement fuse or safety component must be of the same part type and value. ! SUCH REPLACEMENT MUST ONLY BE CARRIED OUT BY A QUALIFIED SERVICE TECHNICIAN.
CE DECLARATION OF CONFORMITY We declare under our sole responsibility that this product is in conformity with the following standards or standardized documents: BS EN 60065 in accordance with the regulations 73/23/EEC, 89/336/EEC (from 1 January 1997) CE 94 Peter Qvortrup, Director Audio Note (UK) Limited 25 Montefiore Road Hove East Sussex BN3 1RD United Kingdom Tel: Fax: +44 (0)1273 220 511 +44 (0)1273 731 498 ! DISPOSAL This product must not be disposed of as normal household waste.
INTRODUCTION Thank you for purchasing this Audio Note (UK) product. With the correct care it should give you many years of pleasure and enjoyment. Please take the time to read all of the information in this manual before connecting your new component to an electrical supply or your system, to ensure both your safety and satisfaction. Please note that due to our desire to continually improve products, specifications are subject to change without notice.
M8 LINE SIGNATURE PRE AMPLIFIER Congratulations on your purchase of the Audio Note (UK) M8 Line Signature premplifier. It is without doubt or question, one of the finest Line Level preamplifiers in production today and is a full Audio Note (UK) Level 5 product. It is well known that the accurate reproduction of music, not just sound, requires the purity of the incoming signal to be preserved.
UNPACKING AND INSTALLATION Please take care when unpacking your M8 Line Signature preamplifier. Choose a clean, clear location to unpack your units. Be aware that the preamplifier and its power supply are extremely heavy; before attempting to unpack or lift the units, check the weight and if necessary use more than one person so that they can be moved safely and easily.
CONNECTION OVERVIEW RCA Inputs Five RCA / Single Ended line inputs are available for connection, labeled ‘SE1 ‘SE2’, ‘SE3’ ‘SE4’ and ‘SE5’; any standard ‘line level’ source can be connected to these inputs. All sockets are colour coded; RED is for RIGHT channel connection, WHITE is for LEFT channel connection. XLR Input In addition to the five RCA inputs, an XLR / Balanced input is provided, for the connection of sources with the appropriate XLR / Balanced outputs.
CONNECTION OVERVIEW continued… Umbilicals Two dedicated cables are supplied for connection of the M8 Line Signature main unit to the power supply. Each cable is colour coded for left and right connection. IT IS ESSENTIAL THAT THE CORRECT POWER SUPPLY OUTPUT IS CONNECTED TO THE CORRECT CORRESPONDING INPUT ON THE MAIN UNIT. Make sure you have correctly identified the corresponding power outputs / inputs before any connections are made.
CONNECTION OVERVIEW continued… M8 LINE SIGNATURE UMBILICAL CABLE CONNECTION R L L R R L R L EARTH CONNECTION
CONNECTION OVERVIEW continued… Mains The M8 Line Signature preamplifier power supply is equipped with an IEC 320 mains inlet socket. Use the supplied mains cable to connect the unit to the local mains supply. The mains fuses are located in the circular receptacles below the mains inlet.
CONNECTION OVERVIEW continued… Outputs The M8 Line Signature preamplifier is equipped with two pairs of Single Ended / RCA outputs, consisting of two colour coded pairs of RCA / Single Ended sockets. RED is for RIGHT channel connection, WHITE is for LEFT channel connection. There are also two pairs of balanced outputs, each consisting of a pair of ‘male’ XLR sockets (see ‘Balanced’ section, below).
CONNECTION OVERVIEW continued… RCA The two pairs of RCA / Single Ended outputs are provided for connection to power amplifiers. They are identical, making them suitable for bi-amping. RCA SOCKET, SHELL = NEGATIVE / RETURN. RCA SOCKET, CENTRE = POSITIVE / SEND. Balanced The M8 Line Signature preamplifier is equipped with custom designed and manufactured output transformers, which feature an improved output and grounding scheme to provide the best possible connection to the power amplifier.
CONNECTION OVERVIEW continued… The pin configuration for all Audio Note (UK) XLR / BALANCED connections is as follows: PIN 1 PIN 2 PIN 3 Ground / Shield Positive / Send Negative / Return The balanced and single ended outputs cannot be used simultaneously; select the appropriate output using the toggle switch. When using an amplifier with a true balanced input, the ‘BALANCED / SINGLE ENDED’ switch may be set in either position.
CONNECTION OVERVIEW continued… CABLE CONFIGURATION OPTIONS POWER AMP INPUT PREAMP OUTPUT 2 1 3 2 XLR FEMALE 3 SCREEN 1 XLR MALE CONVENTIONAL: SCREEN CONNECTED AT BOTH ENDS POWER AMP INPUT PREAMP OUTPUT 2 1 2 1 3 3 XLR FEMALE SCREEN XLR MALE SCREEN CONNECTED AT PREAMP END ONLY, TO ELIMINATE GROUND LOOPS POWER AMP INPUT PREAMP OUTPUT 1 2 3 XLR FEMALE SCREEN RCA MALE CABLE CONFIGURATION FOR XLR BALANCED PREAMP OUTPUT TO RCA UNBALANCED AMPLIFIER INPUT When connecting the XLR / BALANCED
OPERATION Once all the connections are completed and checked, ensure that the volume controls are at the minimum setting (rotated all the way left). Ensure that all source components connected to the M8 Line Signature preamplifier are switched ON. Source components should always be the FIRST components to be switched on and the LAST components to be switched off. Ensure that all power amplifiers connected to the M8 Line Signature preamplifier are switched OFF.
OPERATION continued… Bedding in The new preamplifier requires around 200 hours of initial use (called “bedding in”) before the circuitry becomes stable and optimum performance is realized. As the preamplifier “beds in” the sound will become increasingly smoother, detailed and more open. Once the amplifier has “bedded in” a warm up time of approximately 20 to 30 minutes is required each time the amplifier is switched on before optimum sonic performance is reached.
TECHNICAL SPECIFICATIONS INPUT IMPEDANCE 47K Ohms INPUT SENSITIVITY 160mV for 1V Output GAIN 16dB at 1KHz OUTPUT IMPEDANCE 600 Ohms OUTPUT NOISE -80dB unweighted (RMS) VALVE COMPLIMENT 1 x 6463 (line stage) 1 x 6189 (line stage) 2 x 5651 (PSU) 2 x 6X5 (PSU) 2 x ECL82 (PSU) FUSE RATINGS 1.6A anti-surge (110 / 120V supply) 800mA anti-surge (220 / 240V supply) MAX.
WARRANTY INFORMATION Audio Note (UK) warrants this product to be free from defects in materials and workmanship for two years from the original date of purchase from an appointed Audio Note (UK) dealer, and agrees to cover the cost of parts and associated labour required to correct such defects, subject to terms & conditions. This Warranty is offered to the first purchaser only. Any valves supplied with the unit are warranted for three months from the original date of purchase.
CONTACT INFORMATION If in the future your Audio Note (UK) product requires servicing, or if you require technical support or have any questions regarding this or any of our other products, please contact your local Audio Note (UK) dealer. Alternatively, please feel free to contact us directly: -! Audio Note (UK) Limited 25 Montefiore Road Hove East Sussex BN3 1RD United Kingdom Tel: +44 (0)1273 220 511 Fax: +44 (0)1273 731 498 e-mail: info@audionote.co.
