Owner`s manual

ManualsBrandsAudio Design ManualsAutomotiveHifonics AXi5005

CH 3

CH 4

LINE INPUT

CH 1

CH 2

CH 5

LEVEL HI PASS

6V 0.2V

50Hz

150Hz

BASS BOOST LEVEL

0dB 10dB 6V 0.2V

50Hz 4kHz

LOW PASS

30Hz 150Hz

X-OVER

CH 1/2

FULL

REMOTE

HI PASS LOW PASS

HP FULL BP

X-OVER

CH 3/4

LEVEL

6V 0.2V250Hz 4kHz

CH 5

POWER

PROTECT

MODE

4 CH 5 CH2 CH

SPEAKER OUTPUT

+ –

CH 1 CH 2

+ MONO BRIDGED –

+ – + –

CH 3 CH 4

+ MONO BRIDGED –

+ –

021586

FUSE

LOGO

BADGE

BLUE

WHITE

POWER INPUT

+ –

CH 5

GND BATT +12VREM

INTERCONNECTION

• Connect the RCA lineouts of the headunit with the RCA jacks LINE INPUTS of the amplifier with appropriate high-value RCA

cables. If your headunit is equipped with a separate SUB OUT use this for the CH5 inputs.

• Connect the front speakers with SPEAKER OUTPUT + CH 1 - / + CH 2 -, rear speakers with SPEAKER OUTPUT + 3CH - / + 4CH -

Ensure that the total impedance load of each speaker is not lower than 2 ohms.

• Connect the subwoofer with SUB OUTPUT + CH5 -. Ensure that the total impedance load of the subwoofer is not lower than 1 ohm.

Too low impedance cause high temperature and will shut down the amplifier operation.

• Always ensure the correct polarity of the speakers. The interchange of plus and minus cause total loss of bass playback and could

damage the speakers.

INPUT MODE SWITCH

• Select the 5CH position on the INPUT MODE switch. If there are only two RCA stereo audio cables from the headunit available, connect

the CH1/2 and CH3/4 RCA line inputs and select the 4CH position.

CROSSOVER SETTINGS CH1/2 & CH3/4

• By using bigger speakers (more than 20cm) you can set the X-OVER switch to the FULL position (Full Range Signal).

• By using smaller speakers (8.7cm - 16cm) you must set the X-OVER switch to the HP Position (Highpass Mode) to avoid any damage

by lower frequencies on the speakers. The cut-off frequency is adjustable with the HI PASS controller and should be set between

60Hz to 150Hz, depending on the size of the speakers.

• The LOW PASS Controller from CH3/4 is not in use in this interconnecting example.

LEVEL CONTROLLER CH1/2 & CH3/4 & CH5

• Turn the LEVEL controller of the amplifier to the 6V position.

• Turn the volume controller of the headunit to 80 - 90% of its full setting.

• Turn the LEVEL controller clockwise until you hear some distortion.

• Then turn back the LEVEL controller slightly until you hear a cleaner sound.

BASS BOOST CONTROLLER CH5

• The BASS BOOST controller is continuously adjustable from 0dB bis +12dB.

LOW PASS CONTROLLER CH5

• The LOW PASS controller is for the adjustment of the Cut-Off-Frequency, which should be between 60Hz and 100Hz, depending on

the size of the subwoofer.

BASS REMOTE CH5

• The enclosed BASS REMOTE Controller adjusts if required the bass-level on the subwoofer channel CH5 e.g. from the driver’s seat.

Please use only the enclosed bass remote controller and cable.

AXi5005

Connect the stereo RCA output (FL/FR, RL/RR,

SL/SR) of the headunit with LINE INPUTS

CH1/2, CH3/4 and CH5 of the amplifier.

Loudspeaker

rear / left

2 – 8 Ohms

Loudspeaker

rear / right

2 – 8 Ohms

FR FL

RL RR

Loudspeaker

front / left

2 – 8 Ohms

Loudspeaker

front / right

2 – 8 Ohms

Subwoofer

2 – 8 OhmS

SL SR

Interconnection example: 5-Channel-Mode with Front-/Rear-System and Subwoofer

Connect the bass

remote controller* and

the remote terminal on

the amplifier with the

enclosed cable.

* optional