User manual

Audio Authority HLX Series User Manual 19
Groups
Query a group [QG##] [QG10] (QG10)
(NG10”Empty
Group”)
Group 10 has no members and is named
“Empty Group”.
Add a zone to a group [G##AO###] [G1AO3] (G1AO3) Zone 3 is now a member of group 1.
Switch all zones in a group to a source [CG##I##] [CG2I4] (CG2I4) All zones in group 2 switch to source input 4.
Switch all audio for the zones in a
group to a source input
[CG##AI##] [CG3AI7] (CG3AI7) Group 3 switch audio to source 7.
Switch all video for the zones in a
group to a source input
[CG##VI##] [CG3VI5] (CG3VI7) Group 3 switch video to source 5.
Remove a zone from a group [G##RO###] [G1RO3] (G1RO3) Zone 3 is removed from group 1.
Name a group [NG##”@”] [NG1”Bedrooms”] (NG1”Bedrooms”) Group 1 is named “Bedrooms”
Erase all group memberships [GAR] [GAR] (GAR) All groups now have no zone members.
Network Settings Adjustment
Query current network
(Ethernet) settings
[QE] [QE] (DHCP1) (IP0.0.0.0)
(NM0.0.0.0)
(GW0.0.0.0) (MAC00-
00-5E-A8- 00-D3)
DHCP status, IP address, subnet
mask, gateway, and MAC address are
displayed by this command.
Enable or disable dynamic host
conguration protocol (DHCP)
[DHCP#] [DHCP1] [DHCP0] (DHCP1) (DHCP0) DHCP is enabled (1) or disabled (0).
It is not possible to statically set ad-
dress while DHCP is on.
Dene the static IP address [IP###.###.###.###] [IP192.168.0.212] (IP192.168.0.212) Set the IP address to the specied
value.
Dene the default gateway [GW###.###.###.###] [GW192.168.0.2] (GW192.168.0.2) Set the default gateway for accessing
computers outside of the subnet.
Dene the subnet mask [NM###.###.###.###] [NM255.255.255.0] (NM255.255.255.0) Set the subnet mask, which deter-
mines the computers that can be
accessed without traveling through
the gateway.
Serial Settings Adjustment
Set the serial baud rate [SB#] [SB0] [SB1]
[SB2]
(SB0) (SB1)
(SB2)
Baud rate is set to 9600 (0), 19200 (1), or 115200 (2).
Front Panel Interface Adjustment
Query front panel interface lockout [QFPL] [QFPL] (FPL0) (QFPL) Returns whether the front panel interface is locked out (1)
or unlocked (0).
Enable or disable front panel interface lockout [FPL#] [FPL0]
[FPL1]
(FPL0) (FPL1) Front panel interface is locked out (1) or unlocked (0).
Query front panel IR lockout [QIRL] [QIRL] (IRL0) (QIRL) Returns whether the front panel IR is disabled (1) or
enabled (0).
Enable or disable front panel IR lockout [IRL#] [IRL1]
[IRL0]
(IRL1) (IRL0) Lock out front panel IR (1) or allow it to operate (0).
Set VFD backlight and LED dimming level [SD#] [SD1] (SD1) The VFD and LED brightness level is set (0-3 are valid
levels).
Conguration Utilities
Query the current conguration [QX] [QX] (SC100)
(SD4)
(SBL100)
(SLED100)
(DHCP1) …
All conguration information is displayed.
Backup current conguration [QXSB] [QXSB] [SC100]
[SD4]
[SBL100]
[SLED100]
[DHCP1] …
All conguration information is displayed in square
brackets. This data can be resent to the HLX to restore
settings.
Load the conguration from memory [LOAD] [LOAD] (LOAD) Loads the conguration stored in onboard memory.
Reset the conguration to factory defaults [RESET] [RESET] (RESET) Loads the factory default settings for every option.
Save the current conguration to memory [SAVE] [SAVE] (SAVE) Saves the current conguration settings immediately. There
is a 30 second timer which automatically saves the settings
during normal operation.