User manual

Audio Authority CMX-144 User Manual 11
Example Command(s) Example Output Result
[C,Z1,I1]
[C,Z1,A,I2]
(Z1,I1)
(Z1,A,I2)
Zone 1 is connected to source audio and video 1 provided that no other
zone has restricted this source.
Zone 1 is connected to source 2 audio and the video is left as it was
before, assuming that source 2 is not restricted by another zone.
[P,F]
[P,N]
(P,F)
(P,N)
Switch into low power mode, switch back into normal operating mode.
[I,2] (I,2,35) Front panel zone indicators dim to level 2. Values=1-3 and 0=off.
[R,Z1]
[R,Z1,P]
(Z1,R)
(Z1,R,P)
Zone 1 audio is switched to match the input video source that is currently
selected; all other zones that have selected this source, either audio
or video, are forced to select the next available source (both audio and
video); no other zone is able to select this source in the future. If no
permanent ag (P) is present, the restriction times out after 5 hours.
[A,Z1] (Z1,A) Removes the restriction that prevents other zones from selecting the
source that zone1 is attached to.
[?,Z1] (Z1,I1) Display the requested output (see p12 for more info).
[IRFE] (IRFE) Rear panel IR input disabled, front panel IR enabled.
[LI] (L,I) Ignores all IR input.
[LK] (L,K) Ignores input from front panel key presses.
[S] (S)
(S...)
Save all of the current status setting to memory. If an Ethernet setting
has been changed, wait for (FINISHED...PLEASE REBOOT).
[H3] HELP 3:... Display command syntax. Valid numbers are 1-6, see Example on the left.
[EV,2] AUTOIP.: 0
BOOTP..: 0
DHCP...: 0
SPEED..: AUTO
WEB ENA: 1
WEB RFR: 0
View Ethernet settings – IP address, netmask, gateway, webrefresh timer,
DHCP enable, BOOTP enable, AUTOIP enable. 0=off, 1=on.
[EI 192.168.000.200] (IP 192.168.0.200) Set the Ethernet IP address. Each 3 digit part must contain all 3 digits;
for example, to enter a 1 use 001.
[EG 192.168.001.010] (GW 192.168.1.10) Set the Ethernet default gateway. Each 3 digit part must contain all 3
digits; for example, to enter a 1 use 001.
[EN 255.255.255.000] (NM 255.255.255.0) Set the Ethernet subnet mask. Each 3 digit part must contain all 3 digits;
for example, to enter a 1 use 001.
[ET03] (ET,3) Set the web page auto-refresh time. When viewing the current status web
page, changes made by other control methods will not be displayed until
the web page is refreshed. Auto-refresh is off by default (0). It can be
changed here from 3-10 seconds, 20 seconds or 30 seconds.
[ED,1] (ED,1) Enable or disable ethernet DHCP. A setting of 1 enables, a setting of 0
disables. Note that using DHCP can introduce a delay while an IP address
is acquired.
[EB,1] (EB,1) Enable or disable ethernet BOOTP. A setting of 1 enables, a setting of
0 disables. Note that using BOOTP can introduce a delay while an IP
address is acquired.
[EA,1] (EA,1) Enable or disable Ethernet AUTOIP. A setting of 1 enables, a setting of
0 disables. Note that using AUTOIP can introduce a delay while an IP
address is acquired.
[ES,1] (ES,1) Changes LAN speed. 0=Auto, 1=10 MBPS half duplex, 2=10 MBPS full
duplex, 3=100 MBPS half duplex, 4=100 MBPS full duplex.
[EW,1] (EW,1) Enables/disables web interface.
[FLASH] (FLASH) Begin rmware upgrade. See Upgrading Firmware (Appendix B).