System 10 PRO Digital Wireless System Installation and Operation ATW-1301 UniPak® Transmitter System ATW-1301/L Lavalier Microphone System ATW-1302 Handheld Microphone System ATW-1311 Dual UniPak® Transmitter System ATW-1311/L Dual Lavalier Microphone System ATW-1312 UniPak®/Handheld Combo System ATW-1312/L Lavalier/Handheld Combo System ATW-1322 Dual Handheld Microphone System
System 10 PRO Installation and Operation CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT REMOVE SCREWS. NO USER-SERVICEABLE PARTS INSIDE.REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THE APPLIANCE TO RAIN OR MOISTURE. CERTIFICATION: THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. THIS DEVICE COMPLIES WITH INDUSTRY CANADA LICENSE-EXEMPT RSS STANDARD(S).
System 10 PRO Installation and Operation Installation Receiver Unit Location For best operation, position receiver unit so it is off the floor, in line of sight of transmitter and away from any large obstructions. Keep the receiver unit away from noise sources such as other digital wireless equipment, microwave ovens, as well as away from large metal objects. Keep System 10 receivers 30' (9 m) away from wireless access points.
System 10 PRO Installation and Operation Figure B, C & D — Rear Panel Controls and Functions 1. RJ45 Connector: Use Ethernet cable (not included) to mount receiver remotely up to 328' (100 m) from chassis. 2. AF Level (Volume) Control: Adjusts audio output level of both AF output jacks; maximum output is fully clockwise. 3. Ground Lift Switch: Disconnects the ground pin of the balanced output jack (5) from ground. Normally, the switch should be to the left (ground connected).
System 10 PRO Installation and Operation ATW-RU13 Receiver Unit Controls and Functions Figure E — ATW-RU13 Functions 1. Antenna: Attach antennas and angle them away from each other so a “V” shape is formed. Antennas attach via SMA connectors. 2. Mounting Socket: ¼"-20 thread socket for mounting receiver remotely to tripod or other device with a ¼" screw. 3.
System 10 PRO Installation and Operation ATW-T1002 Transmitter Setup Controls and Functions Battery Selection and Installation Two alkaline AA batteries are recommended. When inserting the batteries, observe correct polarity as marked inside the battery compartment. Power / Battery / Mute Status Indicator Level Control System ID Display Pairing Switch Battery Compartment Screwdriver Figure H — ATW-T1002 Handheld Transmitter Handheld Transmitter Battery Installation 1.
System 10 PRO Installation and Operation Microphone / Instrument Level Control LR6,AA Pairing Switch Screwdriver System ID Display Battery Compartment Figure I — ATW-T1001 UniPak Transmitter ® UniPak® Transmitter Battery Installation 1. Slide off the battery cover. 2. Carefully insert two fresh AA alkaline batteries, observing polarity markings. 3. Replace the battery cover (Fig. I).
System 10 PRO Installation and Operation System Operation Turn down the volume control for both receivers and the mixer/amplifier level before starting up the wireless system. Do not switch on the transmitter yet. Receiver on... Plug the power supply into an AC power source, then turn on the power switch. The blue System ID Display will illuminate. Transmitter on...
System 10 PRO Installation and Operation Clearing Individual ID Pairings 1. Press the receiver’s System ID button to select the ID number you wish to clear. The number will begin to blink. 2. Press and hold the Pair button and, while continuing to hold it, press and hold the ID button until the display shows a blinking “o.” This indicates that your selected ID number has been cleared. 3.
System 10 PRO Installation and Operation Specifications Overall System Operating Frequencies Dynamic Range Total Harmonic Distortion Operating Range Operating Temperature Range Frequency Response Audio Sampling Latency ATW-RU13 Receiver UNIT Receiving System Dimensions Net Weight Remote receiver connector Mounting Thread Insert Accessories Included ATW-RC13 Receiver Chassis Maximum Output Level Power Supply Dimensions Net Weight Remote receiver connector Link Connector Accessorie
System 10 PRO Installation and Operation This page intentionally left blank.
System 10 PRO Installation and Operation Audio-Technica Corporation audio-technica.
