c.LOGiC-Interface C1-RNSE For navigation systems Audi Navi Plus RNS-E Only for vehicles WITHOUT factory rear-view camera Product features • full plug and play multimedia interface • 1 AV-input with separate IR-control channel • control of after-market devices, e.g. DVB-T tuner, DVD-player, DVD-changer, … • after-market rear-view camera input • automatic switching to rear-view camera input (optional coding necessary to switch from OEM-modes) • rear-view camera power (+12V max.
Contents 1. Prior to Installation 1.1. 1.2. Delivery contents Check compatibility of vehicle and accessories 2. Connection schema 3. Installation 3.1. 3.2. 3.3. 3.3.1. 3.3.2. 3.3.3. Interconnecting Interface-box and harness Connections to head-unit Connecting peripheral devices AV-source Installing AV-source’s IR-sensor additionally After-market rear-view camera 4. Operation 4.1. 4.2. 4.3. 4.4. Selecting the c.LOGiC as current AV-source Assigning device control Remote functions Picture settings 5.
Legal Information By law, watching moving pictures while driving is prohibited, the driver must not be distracted. We do not accept any liability for material damage or personal injury resulting, directly or indirectly, from installation or operation of this product. This product should only be used while standing or to display fixed menus or rear-view-camera video when the vehicle is moving, for example the MP3 menu for DVD upgrades.
1.2. Check compatibility of vehicle and accessories Requirements Vehicle Audi A3 (8L, 8P & 8P Sport), A4 (Cabrio 8H/B7/8E, B6/8E), A6 (4B), TT (8J), Lamborghini Navigation Audi Navi Plus RNS-E all-in-one navigation 16:9 Limitations Factory-TV-tuner Must NOT be installed. After-market rear-view camera Only compatible with NTSC-cameras.
3. Installation Switch off ignition and disconnect the vehicle’s battery! If according to factory rules disconnecting the battery has to be avoided, it is usually sufficient to put the vehicle in sleep-mode. In case the sleep-mode does not show success, disconnect the battery with a resistor lead. Place of installation is behind the head-unit. 3.1. Interconnecting Interface-box and harness Page 4 Plug harness C1C-RNSE into 12pin Molex of Interface-box C1C-RNSE. Version 29.11.
3.2. Connections to head-unit Remove the head-unit from the dash-board. Plug female 32pin AMP-connector of C1C-RNSE into male 32pin AMP-socket of headunit. Note: If the 32pin AMP-socket of the head-unit is already occupied, the vehicle probably has a factory rear-view camera or a factory TV-tuner. In case of a factory tuner, it must be uninstalled: disconnect the female 32pin AMP-connector of the factory harness and disconnect all wires from the factory TV-tuner.
3.3. Connecting peripheral devices It is possible to connect one after-market AV-source and an after-market rear-view camera to the c.LOGiC Interface. Before final installation of the peripheral devices, we recommend to test-run the c.LOGiC functions to detect incompatibility of vehicle, navigation, factory accessories or peripheral devices as soon as possible. 3.3.1. AV-source The c.LOGiC interface has the possibility to connect and remotely control by navigation buttons one pre-programmed device.
3.3.2. Installing AV-source’s IR-sensor additionally Additionally to the control via OEM navigation, it is possible to install the original IR-sensor of a connected device. By using the respective Y-adapter (e.g. STA-Y35MM or STA-RJ12) for the IR-Port of the connected device, the controls of navigation AND device’s IR-sensor can be connected and used simultaneously. Installation of the IR-sensor is recommended as the controls via navigation are limited, and not all functions may be covered. 3.3.3.
4. Operation 4.1. Selecting the c.LOGiC as current AV-source Push the CD/TV button of the head-unit to choose the c.LOGiC as current AV-source. 4.2. Assigning device control After selecting the c.LOGiC as current AV source, longpress key SETUP. The FIS will display “TV 1” and “RC01”. Turn right knob until the device-related IR-code as described in device control table for the AV-source (appendix A) is reached. Push right knob to confirm the assignment.
Button assignment table c.
5. Specifications Operation voltage Stand-by power drain Operation power drain Power consumption Temperature range Weight Measurements (box only) B x H x T 10.5 – 14.8V DC <1mA 240mA 3W -30°C to +80°C 75g 106 x 30 x 71 mm 6. Technical Support Caraudio-Systems Vertriebs GmbH manufacturer/distribution Rheinhorststr. 22 D-67071 Ludwigshafen am Rhein NavLinkz GmbH corporate sales/tech dealer-support Eurotec-Ring 45 D-47445 Moers phone +49 180 3 907050 email support@caraudio-systems.
