Audi Installation Instructions Version 1.
Kit Contents: • Bluetooth ECU • Microphone • Vehicle Interface Loom • Operating Manual Tools/Ancillaries Required: • Panel Removal tools • Torx screwdriver •Vehicle Diagnosis Computer, e.g.
Contents Procedure: 02 1.1 General preparation of the vehicle for installation of the components 03 1.2 Mounting the Bluetooth ECU 03 1.3 Routing the Vehicle Interface Loom 03 1.4 Connecting the Vehicle Interface Loom to the Radio/Radio Navigation unit. 03 1.5 Microphone Installation 04 1.6 Coding the vehicle for Telephone 04 1.7 Functional test and final fitting 07 1.8 Vehicle Specific ECU Mounting Locations 08 1.
Procedure: PLEASE NOTE: • Installation of the Integrated Bluetooth Hands-free Phone System should be carried out by a competent workshop. Special tools, diagnostic equipment and special literature specific to the car is required for fitting. • Incorrect installation can result in damage to the vehicle or the product.
1.2 Mounting the Bluetooth ECU • Clean the underside of the Bluetooth ECU with a clean towel and alcohol, and then attach double sided fixing tape to the underside of the Bluetooth ECU. • Mount the ECU with the sockets facing upwards (if ECU is to be mounted vertically) so that the plugs cannot fall out. • Please see pictures Section 1.8 for vehicle specific ECU mounting positions. 1.
1.5 Microphone Installation • Please see Section 1.9 for vehicle specific Microphone mounting positions. • Clean surface that the microphone is to be mounted to with alcohol and clean towel. • Once the Microphone is mounted in the correct position, route the cable to the Bluetooth ECU location. • Secure the microphone cable using the supplied cable ties within the dashboard to the existing wiring/wiring looms. • Connect the microphone plug to the Bluetooth ECU 2.5mm microphone socket.
Head Unit Coding The following head units require coding, if not listed here they do not need coding. • RNS-E Head Unit Address 56 (Radio) 0XXX?XX- Digit marked ? Has to be changed to 7 The RNS-E head unit need to have a software index of at least 350. RNS-E RESET After coding you need to complete a RESET of the head unit. Please turn the device off. When the head unit is turned back on keep the ON/OFF button held down for 45 seconds until the head unit resets.
Chassis Coding • Chassis A4 8E and A6 4B Address 17 (Instrument cluster) Channel 62, add 2 to the existing value (e.g. 17 to 19) • Chassis A4 8E Address 16 (Steering Wheel) 02XXX– change 02XXX to 03XXX • Chassis A6 4B and A8 4D Address 16 (Steering wheel) 0XXX2– change 0XXX2 to 0XXX1 • Chassis A38P,TT8J,A48K,A58T,A58F,Q58R Address 19 (CAN gateway) - Select Address 19 – Diagnostic Interface Databus - Select Coding - Option 77 Telephone - Set option 77 to coded.
1.7 Functional test and final fitting • Check the function of the Integrated Bluetooth Hands-Free Phone System by pairing a mobile telephone to the system (Bluetooth ID is BT Gateway, PIN code is 1234) and then make a call. End the call via the Multi Function Steering Wheel. • Test the answering function by calling the paired mobile telephone from another phone and answering using the Multi Function Steering Wheel.
1.8 Vehicle Specific ECU Mounting Locations STEERING COLUMN 1A A3 (8P), TT (8J) Remove bolt behind trim panel & two bolts underneath dash. 1B A3 (8P) Location: Mounted to dash support brace using double-sided tape. STEERING COLUMN 1C A4 (8K) A5 (8T & 8F) Q5 (8R) Remove bolt behind trim panel & two bolts underneath dash. FUSE BOX FUSE BOX 1D A4 (8K) A5 (8T & 8F) Q5 (8R) Location: Mounted to dash support brace using double-sided tape.
1.9 Vehicle Specific Microphone Mounting Locations 2A A3 (8P) Location: Attached to trim panel with wire routed behind trim panel. 2B A4 (8K) A5 (8T & 8F) Q5 (8R) Location: Attached to steering column shroud with wire routed behind vinyl. 2C A4(B7) Location: Attached to trim panel with wire routed behind trim panel.
