Digital Radio User's Manual Rev.
To Users Thank you for purchasing our product! This Manual is designed to make you quickly grasp use of this device. In order to avoid physical injury or property loss due to improper operation, please read this Manual carefully before using this device. Notice The device meets the requirements of FCC PART 90, PART 97 and PART 15. Local laws and regulations shall be complied with when setting up or using the equipment, and corresponding qualifications and relevant procedures shall be obtained if necessary.
(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. ISEDC RSS warning This product meets the applicable Industry Canada technical specifications. / Le présent matériel est conforme aux specifications techniques applicables d’Industrie Canada. RF Radiation Information Using Tips 1. This product is limited to occupational applications that can meet RF energy radiation requirements.
·In vehicles with airbags, do not place the radio in the area where airbag deployment may be involved. ·Please turn off the radio before entering flammable or explosive environment. ·Do not replace or charge the battery in a flammable or explosive environment. ·Please turn off the radio before approaching the blasting area and the detonator area. ·Do not use the radio with damaged antenna. A damaged antenna may cause minor burns when it comes into contact with the skin.
RF Exposure Compliance and Control Guidelines and Operating Instructions Using Tips 4 To control your exposure and ensure compliance with the occupational/ controlled environment exposure limits always adhere to the following procedures. Guidelines: • Do not remove the RF Exposure Label from the device. • User awareness instructions should accompany device when transferred to other users. • Do not use this device if the operational requirements described herein are not met.
• For a list approved accessories please consult your local dealer for information. European Union (EU) Waste of Electrical and Electronic Equipment (WEEE) directive: The European Union's WEEE directive requires that products sold into EU countries must have the crossed out trash bin label on the product (or the package in some cases). As defined by the WEEE directive, this cross-out trash bin label means that customers and end-users in EU countries.
lors de la transmission (en termes de mesure pour la conformité aux normes). • Tenez la radio en position verticale devant le visage avec le microphone (et les autres parties de la radio, y compris l'antenne) à au moins 2,5 cm du nez. Garder la radio à la bonne distance est important car les expositions RF diminuent avec la distance de l'antenne. L'antenne doit être tenue à l'écart des yeux.
User Interface Know the Radio 7
About the Device 1 2 3 4 5 6 Antenna Alarm key PTT key P1 key P2 key Channel selection knob 7 8 9 10 11 Power switch/Volume knob LED indicator Interface Speaker Microphone Radio LED Indicators Know the Radio 8 Radio Status LED Indication Standby Blinking Green Low Battery Blinking Red Transmit (TX) Solid Red Receive (RX) Solid Green Programming Mode (Read from Radio) Fast Blinking Red Programming Mode (Write to Radio) Fast Blinking Green Scanning Slow Blinking Orange Call hang time mo
Power On/Off and Volume Control Power on/off: Turn the power switch knob to turn on/off the radio normally. Note: The battery needs to be charged, otherwise the radio cannot be turned on under low power state. Volume control: In standby state, turn the knob clockwise/ counterclockwise to adjust the volume that fits your ears. Installation: Know the Radio Battery Installation or Remove Align the battery as shown in the picture, press and slide in the battery until the latch snaps into place.
Antenna Installation Align the antenna with the connector on the top of the radio, and screw it in clockwise until it is tightened. Note: Do not hold the radio by its antenna; otherwise, the performance and service life of radio may be affected. Belt Clip Installation Step 1: Remove the belt clip screws from the device. Step 2: Align the radio screw holes on the belt clip, and then tighten the screws. Accessory Installation Step 1: Open the accessory connector cover.
Charging Function Battery pack charging Charge Indicator LED lndicator LED no light LED glows red LED glows green Charge Status No load Charging Fully Charged Know the Radio Device charging Charging precautions: ·Please use the original charger tray of the model for charging. · When charging, it is recommended that the radio remain powered off during charging. ·To obtain the best battery performance, please charge for at least 5 hours for the first time.
· The battery pack should be stored in a cool and dry place after being fully charged. Do not expose the battery pack near the fire or to the sun, otherwise there are safety risks. ·During charging, it is not recommended to transmit the radio. ·The battery pack may slightly heat up during charging, which is a normal phenomenon. Channel and Zone Selection Know the Radio Rotate the [Channel Selection] knob clockwise or counterclockwise to switch to the desired channel. Zone: A zone is a group of channels.
Transmitting/Receiving After starting up successfully, the user can conduct various call operations. Precautions for radio use: ·When the radio is transmitting, keep the radio in a vertical position, and keep the microphone 2.5-5 cm away from the mouth. When transmitting, the radio should be at least 2.5 cm away from the head or body. ·Do not turn on/off the radio repeatedly during use, and adjust the volume to a level suitable for your hearing. Precautions for radio operation: 功能 介绍 Features 1.
Program Button User can configure program button functions via programming software. Corresponding features as below: - None - Monitor - Scan On/Off - Direct Mode On/Off - High/Low Power - Emergency Call - One Touch Call - Zone Selection - VOX On/Off - GoGrouping 功能 介绍 Features Device Name Configuration and Modification 1. Enter the basic setting interface of programming software to configure or modify the device name. 2. Device name can support: Letters, numbers, Chinese, special characters, etc.
Password Configuration 1. To prevent information leakage, you can set the reading and writing password through programming software. 2. Each time you read or write, you must enter the correct 8-digit password before operating. 3. To cancel the password, clear the password and confirm. 4. To change the password, key in the old password first, and then enter the new password to rewrite. 5. When you forget the password, you can perform factory reset or reprogram it. Sub-Code Configuration Features 1.
Scan List Configuration 1. 2. 3. 4. The scan list can contain analog channels and digital channels. After configuring the scan list, the scan switch should be turned on. Turn on/off the scan list through preprogrammed [P1/P2] key. During scanning, the channels scanned include the channels in the scan list and the current main channel. 5. When any channel in the scan list is transmitting a signal, it will stay on that channel upon signal detection. High/Low Power 功能 介绍 Features 1.
such as alarm channel, re-transmission times, and alarm type. 2. Emergency call supports the digital channel and analog channel. 3. Set the side button as the“Emergency Call” button in the “programmable button”. 4. When Analog or Digital channel triggers emergency call, an emergency call code will be sent. Emergency call will be automatically transmitted after remaining re-transmit call becomes 0, and automatic emergency calls will repeat transmit twice. 5.
Contacts 1. Contacts are only valid for digital channels. 2. There are three kinds of contacts: private call, group call and all call; and each digital channel needs to be set through programming software. 3. When making private call, only when the frequency is the same, the other party's ID exists and is in standby state communication can be made. 4. When making group call, pay attention to whether the contact is in the receiving group, and all radios in the same receiving group can receive the speech. 5.
on the interface. 3. Configure “One touch call” through programming software and send “Remote Monitor”. Radio Check (Private call only) Radio check is used to check whether it can communicate normally with the other party. 1. Configure “One touch call” through programming software to send “Radio Check”. 2. After “Radio Check”is sent successfully, it will prompt a beep sound, otherwise error tone will sound. 3.
Note: Changing the channel will cover the leader's frequency setting include contact, color code or tone code settings. 功能 介绍 Features 1. Configure the programmable key as a “GoGrouping” through the programmable software. 2. A group of radios in mutual communication, one or more sets to operate the temporary teaming function: press the programmable button preset as “GoGrouping” to enter the frequency allocation mode, and the indicator flashes green. 3.
by writing frequency or receiving the "activation" command. Activate (Private call only) 1. The activation command is to remove kill status. 2. After sending activation command, it can change the other party from remote kill state to active state. After restarting, it can be used normally. Voice Control Function TOT Function Features 1. Preset the [Program] key to [VOX On/Off] key through programming software. 2. Press the [VOX On/Off] key to turn on/off the voice control function.
Power saving function To extend battery life, the user can enable power saving mode. In the power saving mode, the user can press [PTT] key to transmit or the radio can receive normally when a signal is detected. The power saving function can be enabled/disabled by programming software. GPS Function (for specific models only) Features 1. After turning on GPS, you can get the latitude, longitude, current time, date, number of satellites, speed, etc. of the current time zone in the open field. 2.
Optional Accessories Default accessories of the device are included in the product packaging box. For more information about accessories, please consult your local dealer. Disclaimer This manual strives for the accuracy and completeness of its content during the preparation. Repeated review has been carried out, and the company will not assume any responsibility for errors or omissions that may occur during the output and printing process.
Model Number: Telephone: Post Code: User’s Name: Chop b y Dealer 4.Warranty void if seal broken. 5.1 year guarantee for product, 6 months for charger,battery and antenna . 6.The user can get repairing service from the following ways: a.Go to the shop where you buy the machine b.Our local repairing agent REMARKS: 1.This guarantee card to be kept by the user ,no replenishment if lost. 2.This guarantee card to be filled & chopped by the dealer,or it is invalid. 3.
+