Convergence User Manual 335100390_RevA 1
Thanks for Using! The Manual introduces the information about CONVERGENCE installation and use.
To User Thank you for purchasing our intelligent converged communication device CONVERGENCE (hereinafter referred to as “the Product”). The Product greatly simplifies your life and work based on advanced techniques and exquisite craft. Please read the Manual carefully before using the Product to master the use and avoid personal injury or property loss due to miss operation. Tips Please keep the Manual properly for further reference and use.
User Safety Information Please read the following safety information for using the Product at higher efficiency. The radio can only be maintained by professional technicians. Do not disassemble the radio without permission. Only designated power adapter, antenna and components should be used. Do not install the Product in flammable and explosive places. Do not install the Product in places close to explosion or detonator. Do not use the radio with damaged antenna.
The European Union's WEEE directive requires that products sold into EU countries must have the crossed out trash bin label on the product (or the package in some cases). As defined by the WEEE directive, this cross-out trash bin label means that customers and end-users in EU countries. Overheat Warning Do not touch the Product with hands when the Product has been running for long period and surface temperature is too high, for the power amplifier radiator may be under high temperature.
Device Overview Part List Part No.
Installation Preparation Voltage Inspection Check if voltage of DC power or external power supply is within the range of the Product’s working voltage (13.5 V±10%). Product Inspection Power on and check if the Product is running normally by inspecting the status of all indicators on front panel. Please refer to “Basic functional operation” for details. Fittings Installation Firstly install RF antenna, power adapter and LAN cable before the Product is powered on.
Assemble/Disassemble of LAN Cable Insert LAN cable into LAN Ethernet port (RJ45). Remove the LAN cable connector to disassemble the LAN cable. Assemble/Disassemble of Backup Battery (Optional) Connect the connector of backup battery to the female connector of backup battery and fasten it clockwise. Rotate the connector at cable end of backup battery anticlockwise to remove the backup battery.
Parameeter Config guration portant: Pleease contact local dealer to configuree the followin ng parameteers before usee: Imp Con nfiguration of Intelligent Relay 1. Configure the following parrameters of thhe Product viia programmiing software: Group numbber of privatee network Tx/Rx Frequuency The Productt’s serial num mber （refer to t product lab bel) Domain nam me and port number n of loggin backstage server 2.
Basic Functional Operation Ensure Product is connected to LAN cable and power supply. Note: Once LAN connection setup completed, LAN network (Ethernet) will auto connect to server when power on Press Power switch to power on, power indicator will be turn in blue and narrow-band indicator will flicker slowly in green (1.0s on, 5.0s off). * 10 Slow flickering Quick flickering When network is in searching mode, the LAN indicator will flicker slowly in green (1.0s on, 1.5s off) .
* Normally on Slow flickering Quick flickering Status Indicator Power indicator Host Status Power Indicator Status Flicker Period Power off Blue indicator off / Power on Blue indicator on / Host Status Narrow-band Indicator Status Flicker Period Standby Green indicator flickering 1.0s on, 5.0s off Call Red indicator normally on / Receive voice Green indicator normally on / Host Status Broadband Indicator Status Flicker Period Network searching Green indicator flickers slowly 1.
* Normally on Slow flickering Quick flickering Back Up Battery Notice Please firstly charge the battery before use for it is uncharged before delivery. The battery service life can be affected if battery is long idled or consumed up. The battery should be given one circle of charging/discharging on a semiannual basis to maintain the optimal status of battery capacity. Replace the battery if it has insufficient volume or fails to fully exert discharging.
Call The Handset can realize no-difference intercom between Handset at long distance or under strong interference through two Convergences. For example, press the PTT key of Handset A for emission and in the emission process, the indicator on the corresponding relay A will be normally on (green). Handset B will receive the call voice, and the Handset indicator on relay B corresponding to B will be normally on in red.
Then re-install the seal cover. Installation There are 2 ways to mounting the Product to （1） wall or （2） Cylindrical Post/Rod. Note: During the installation, ensure the RF antenna side is always facing upward. (1) Wall Mounting 14 Fix the Product at the desire location using 4 pieces of M7.
(P Plane Mountin ng) t RF antennna side is alw ways facing uppward. For installattion , ensure the (2) Cylindricaal/Rod Mou unting Fix the cylinndrical mounnting on the Product P using g 4 pieces of M3*8 M washerr head screwss and then fix the Product on thhe cylinder ussing two steel rings,as shoown in diagram below. steeel rings (Cyliindrical Moun nting) For installattion , ensure the t RF antennna side is alw ways facing uppward.
Optional Components The main accessories of the Product are included in the product box. For more information about accessories, please consult your local dealer. Note: Please use the accessories specified by our company, if unauthorized use of unauthorized accessories, the consequences are the responsibility of the user.
socket Backup battery is not installed or it has abnormal voltage Install backup battery correctly and make sure it has sufficient power Receiving and transmission Check if frequency points are frequency point of the Product matched and reconfigure them is unmatched with handset if necessary Find the interference signal sources, or apply for changing the communication frequency point if the source cannot be closed or the interface source is long-distanced Communication failure Team member is out range.
Auctus Technologies Co., Ltd. Building 17, Phase 3, China Academy of Science & Technology Development (CASTD), Gaoxin South No. 1 Road, Nanshan District, Shenzhen Tel.: +86 755 2606 8685 Fax: +86 755 2640 5328 E-mail: info@auctus.cn Website: www.auctus.
