ATV 200 & 300L UV 400L Operator’s Manual
GENERAL INFORMATION & SPECS ����������3 Operation �������������������������������������������������4 Calibration �����������������������������������������������4 Spray Application �������������������������������������5 Storage �����������������������������������������������������5 Identification ��������������������������������������������6 Dimensions ����������������������������������������������6 MAINTENANCE & TROUBLESHOOTING FOR 12V UNITS........................................7 PARTS LIST...............
GENERAL INFORMATION & SPECS off to the pump at a pre-determined high pressure point. As the outlet side of the pump is opened, the pressure starts to drop and at a predetermined point (typically 40-75 psi) contacts in the switch will lose causing the pump to start automatically. The pump will then pump until the pressure reaches the shut-off pressure point. Tank: All tanks are constructed from UV resistant polyethylene. Polyethylene tanks have a very high chemical resistance.
Operation Calibration Connections All sprayers need to be calibrated and kept in good condition. This will ensure that the correct rate of chemical is applied to the target. The following steps should be followed when connecting to a power source: 1. Ensure that the battery is 12V DC Follow these steps to calibrate the sprayer: 2. Connect the red connector to the positive (+) terminal and the black connector to the negative (-)terminal. 1.
Spray Application it is recommended that you consult the chemical label or your chemical supplier. After completing the filling process, you are now ready to start spraying. 1. Turn pump off 3. Add a quantity of fresh water to main tank and then drain. NOTE: It is the responsibility of the operator to ensure that the chemical mix is sufficiently agitated and that the conditions are right to start spraying. Operators must wear the appropriate PPE. 4.
Identification When ordering parts or requesting service information for your sprayer it is important to quote the serial number of your machine, and the purchase date, in order to receive accurate information. The location of the serial number is shown in the picture. This serial number is stamped into the serial number plate. Dimensions Model Width Length Height Dry mm mm mm Weight 200 Lt ATV with 12V pump & 3 Mt al.
MAINTENANCE & TROUBLESHOOTING FOR 12V UNITS The troubleshooting information is provided as a reference when your sprayer is not functioning correctly. To ensure that you receive the best possible service, it is recommended that you exhaust all applicable troubleshooting solutions shown prior to calling your dealer for service advice.
PARTS LIST ATV200/3 GA4905995 ATV300/4 Position Part No GA4905975 Description Quantity 1 GA4515600 ATV tank support mount 2 2 GA5023670 Mini hub & stub ass 2 3 GA5023665 Tyre nobby (22x11-8 x 6 ply) & 4 stud mini rim 2 4 300120 Filter, basket type, diam 305 x 245 deep 1 5 GA8500000 GA5023660 GA5023750 Tank, 200L, ATV low profile, green Tank, 300L, ATV low profile, green Tank, 400L, UV low profile, green 1 6 GA4522140 Tow ball mounting plate 1 7 GA5049100 Trailer coupling 50mm
Position Part No Description Quantity 16 GA5066085 15 mtr hose reel manual, 3/8” 1 17 GA5053250 Pressure gauge, small face, 0-400kPa 1 18 GA4900546 Gunjet, AA30, adjustable nozzle with fittings 1 19 GA5015971 Sticker Drain Only 1 20 GA5020620 Valve, ball, 12mm thread male/female inlet/ outlet, lever handle, SS 1 21 HB050-90 Hose barb, Elbow, 90 degree, 1/2 male thread x 1/2 hose, Banjo (not shown) 3 22 HOS12SIGHT Hose, clear, 12mm sight tube (not shown) 4 23 GA5007231 Hose
12v pump wiring diagram Important: Use 14 gauge stranded wire up to 6 metres from power source and 12 gauge up to 18 metres from power source. Connect Red to Positive (+) terminal and Black to Negative (-) terminal. Pump Diagrams Spare parts available for GA5066540 Pathway 13.
IOTA 20 PUMP Gear Box & Honda GX100 engine 6 1 4 10 7 5 2 3 9 8 290psi/20bar 20 l/min@550rpm 6:1 Reduction Gearbox 3hp Honda GX100 Engine Number Description 1 Control valve 2 Pump 3 Gearbox 4 Choke 5 Pull cord 6 Fuel cap 7 Spark plug 8 Muffler 9 On/Off switch 10 PART NUMBER GA5023895 5091D9 IOTA20 Air damper 12 DESCRIPTION 3hp GX100 engine Udor 6.
Wheels & Tyres To determine the correct tyre pressure: 1. Determine the maximum weight of the sprayer when loaded (do not forget to add the weight of the rinse water tank and the foam marker tank when filled). All tyres used on Goldacres sprayers have been designed to carry the maximum loaded weight of the sprayer when travelling at 20 km/h. The load capacity of the tyres decreases as travelling speed increases so it is important to heed this travelling speed limit. 2.
MANUAL FOLDING BOOMS General information Boom height The standard nozzle spacing on Goldacres booms is 500mm. For this spacing, the optimum height the boom should be from the object to be sprayed (with a 110° fan angle nozzle) is 500mm. The boom fitted as standard is part of the Goldacres range of “folding booms” which are available in sizes from 3 metres to 10 metres.
Operating instructions for folding booms Folding boom lubrication Folding booms have a grease nipple fitted at each pivot point. Grease these points regularly with quality multi purpose grease. 1. Starting with the boom in the closed position (Fig.1), pull each wing against the spring in an out and down manner until open and resting against the stop plate with the adjustment bolt. 2. With both wings folded out into the open position, (Fig. 2) check that boom is aligned correctly. 3.
30m manual hose reel Ref. No PART NUMBER DESCRIPTION 1 GA5066080 30 Mt manual hose reel 2 GA4900546 AA30L GunJet with adjustable brass ConeJet 3 5500X18 Adjustable ConeJet 4 GA5020875 Male tailpiece ¼˝ thread x ½˝ barb Part No. QTY.
AA30L GunJet The gunjet trigger needs to be locked via the trigger lock when not in use to prevent the gunjet from spraying inadvertently.
Adjustable ConeJet Nozzle The adjustable brass ConeJet nozzle rotates through a half turn to provide spray selection from wide angle, finely atomized cone spray to a straight stream spray. Tip settings “A” and “B” represent two extreme points of rotation in tip adjustment. ADJUSTABLE CONJET TIP NO. 5500-X18 Standard 5500-X22 5500-X26 PERFORMANCE LIQUID PRESSURE (bar) 1.5 A 2 B 3 A B 4 A B A B Capacity—l/min 0.79 2.61 0.98 3.18 1.14 3.67 1.40 4.
IMPORTANT SAFETY MESSAGE FOR OWNERS & OPERATORS • Do not attach other equipment to the ATV spray tank. This may exceed the ATV spray tank’s designed capacity and function. • Reduce speed when operating the ATV spray tank when tank is loaded. • Allow for greater braking distances when the ATV spray tank is loaded. • To reduce possible ATV instability it is recommended the ATV be stationary if spot spraying on a slope or hill.
SAFETY when transporting, or towing, be adhered to at all times. • General The following pages outline important safety information. At Goldacres safety is a high priority. These safety and warning instructions MUST be followed to ensure the safe operation of your Goldacres equipment.
• Safe use of chemicals Area surrounding equipment may become slippery when wet. The safe use of Ag chemicals with this equipment is the responsibility of the owner/operators. All operators should be trained in the safe use of Ag chemicals. Goldacres suggest that a relevant course is completed by owners/operators prior to operation of this equipment as a spray unit. Notes • Always read and understand the operator’s manual prior to operation of this equipment.
Safety Decals Identification Understanding safety decals and their purpose assists in the safe operation of your sprayer. Safety decals are there for your protection and it is the responsibility of the owner operator to replace damaged and/or missing safety decals. When ordering parts or requesting service information for your sprayer it is important to quote the serial number of your machine, and the purchase date, in order to receive accurate information.
GA8700118 ATV 200 GA8700118 ATV 200 tank decal GA5065065 GA5065005 ATV 300 GA5065005 ATV 300 tank decal UV400 GA5065065 UV400 tank decal 23
TERMS AND CONDITIONS Interpretation 1. In terms and conditions: (1) “Goldacres” means Goldacres Trading Pty. Ltd. A.C.N. 061 306 732 trading as Goldacres Agricultural Equipment (its successors and assigns) which is the seller of the Goods; (2) “Purchaser” means the purchaser of the Goods; (3) “Goods” means the products and, if any, the services sold or provided by Goldacres to the Purchaser; (4) “GST Act” and “GST” are given the meanings referred to in a New Tax System (Goods and Services Tax) Act 1999.
(7) The Purchaser agrees (other than as provided in these terms and conditions) not to sell, lease, mortgage, deal with, dispose of or create or attempt to create any other security interest in or affecting the Goods unless and until the Purchaser’s Debts have been satisfied.
NOTES: 26
NOTES: 27
1-3 Morang Crescent, Mitchell Park Vic 3355 P: 03 5342 6399 F: 03 5342 6308 info@goldacres.com.
