RL100 OWNERS MANUAL
Register your K40 RL100 today to activate your guarantees: Guaranteed immunity from speeding tickets If you get a speeding ticket within one year of purchase, we’ll reimburse you for the full cost of the ticket.* Guaranteed performance If your K40 radar detection system does not outperform any other radar detector you’ve owned, return it within 30 days for a full product credit. One year warranty K40 offers a one-year “repair or replace” warranty if your product fails to work properly.
Mounting and Powering the RL100 Mounting Instructions To help ensure that your RL100 functions properly and offers maximum protection, please follow these mounting instructions: 1. Clean the area of the windshield where the unit will be mounted.* 2. Attach the supplied Windshield Mounting Bracket to your car’s windshield by firmly pressing the suction cups in the bracket to the windshield. a. Mount the bracket as low as possible near the center of the windshield. b.
Quick Start (using factory default settings) Once your K40 RL100 has been mounted and had the power connected, you may begin using immediately by following these steps: 1. Switch on the RL100 – Turn the Power On/Volume Control Wheel on the side of the unit. 2. Wait for Test Scan to complete – The radar detector will announce(voice) and display(screen) K40 SCAN then go through a “wake up sequence” lasting approximately 5 seconds. a. You will hear and see all bands tested. Adjust the volume during this test.
Receiving Alerts The K40 RL100 provides a combination of audio and visual alerts to warn you when radar and laser signals are detected. Radar Alert Sequence The RL100 detects X, K and KA-Band radar signals. When a signal is identified: • A voice alerts which band was detected. (This assumes the factory default “Voice ON” setting has not been changed.) • A series of beeps indicates the strength of the signal. Each band has its own distinctive beep. (Volume reduces automatically after 5 seconds.
Laser Alert Sequence When the RL100 detects a laser signal: • A voice alerts announces “Laser.” (This assumes the factory default “Voice ON” setting has not been changed.) • You then hear a distinctive audio tone. (Volume reduces automatically after 5 seconds.) • Display indicates laser has been detected and reports your speed. • NOTE: Unlike radar, signal strength from laser remains constant. Laser Alert Example: You are driving 55 mph and laser is detected.
Special Features/Functions Mute Sounds Using the MUTE button, the RL100 provides you two ways to mute audio alerts (both voice and tones) for either 15 seconds or 2 minutes: • OPTION 1: Silence all audio after an alert has sounded. • OPTION 2: Silence all audio for a preset time before any alert occurs. (Example: You may mute sounds for 2 minutes prior to making a phone call.
• • To activate, press and release MARK button when you are at the location. Display shows Mute Loc and voice announces “Location Muted”. • In the future, alerts will be muted within a 1500-foot radius of the point marked. • Though muted, you will still receive full visual indication of the alert. Level 2, FULL ALERT — Provides you both audio and visual alerts for a specific location you’ve stored. (Examples: school zone, speed camera, red-light camera intersection).
Reference Guide RL100 Radar and Laser Detection Windshield Mounting Bracket (with suction cups) – For proper installation, see page XX Power Cord – Plug into cigarette lighter or other 12v outlet Power Input Jack – Insert small end of power cord here Power On/Volume Control Wheel – Turn on the RL100 unit and adjusts volume of voice/tones MENU/DIM Button – Press and release to change display brightness from bright (factory default) to dim or dark, or press and hold for 3 seconds to enter MENU mode (page
Speaker – Alerts delivered via voice and tones FILTER Button – Press and release to select level of alert sensitivity (page XX), or enter “Speed Monitor” function by pressing and holding for 3 seconds (page XX) MARK Button – Choose two levels of alert at specific locations you identify and “mark” (page XX) MUTE Button – Press and release mutes audio alerts for 15 seconds, or press and hold for 3 seconds to engage a 2-minute mute (page XX) Alphanumeric Display – Provides alert information as well as spee
Filter Operation (i.e. signal sensitivity) The Filter system on the RL100 offers you 3 levels of sensitivity settings to accommodate various driving situations. To change the level at any time, press and release FILTER button. Level / Mode 1. Highway (factory default setting) Sensitivity Detects all types of police radar or laser signals at full sensitivity. Recommended Use For highway travel or in any area in which you are unfamiliar with the types of radar used. 2.
Speed Monitor The Speed Monitor function alerts the driver when a preselected speed is exceeded. The Speed Monitor can be set to any speed between 40-100 mph in 5 mph increments. When the preset speed is exceeded: • The RL100 emits a “Slow Down” voice alert accompanied by the visual display SlowDown. • The alerts will continue until the vehicle’s speed is reduced to below the Speed Monitor setting. The factory default setting for speed monitor is “Off.
Menu / Customizable Settings The RL100 comes with factory default settings on certain features that we’ve learned are desirable for the majority of our customers. However, we provide you with the option of changing the settings based on your preferences. To access and change any of the 12 selectable preferences: • Press and hold MENU button for 3 seconds. The voice will announce “Menu” and the display will read *MENU*.
Menu Options (in order displayed) 1 2 3 4 5 6 7 8 9 10 11 12 Default Setting Description Voice Type Audible Voice Female Choose male or female voice for audio alerts. On For all initial audio alerts: “Voice On” uses voice; “Voice Off” uses tones only. Test On Controls length of startup sequence after powering on unit. “Test On” is standard 5second test. “Test Off” uses an abbreviated sequence. Speed Displayed On “Speed On” displays current speed in mph when driving over 5 mph.
Troubleshooting Guide Problem Possible Cause Solution Plug not inserted properly Reinsert plug and rotate Defect in power cord Replace fuse with 1 amp 250 Volt 3AG fuse Lighter socket not clean or negatively grounded Consult your dealer or auto mechanic power) Defective fuse or electrical wiring for lighter socket Consult your dealer or auto mechanic Week or no Partially blocked antenna or Reposition the unit to ensure lens opening unobstructed view of the road ahead No visual display or audio
Product subject to one or more of the following patents: Learn more at k40.
FCC ID: W75-M1K-Y12 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. In addition, any changes or modifications to this product, which are not expressly approved by K40 Electronics in wiring, could void the user’s authority to operate this product.
Elgin, IL 60123 800.323.6768 Learn more at K40.
