Atrie DB108 WL User Manual Atrie DB108-WL WIRELESS ADSL MODEM USER MANUAL (V3.
Atrie DB108 WL User Manual CONTENTS 1 OVERVIEW....................................................................................................................................................... 2 1.1 ABOUT ADSL .......................................................................................................................................................................2 1.2 DEVICE INTRODUCTION .......................................................................................................
Atrie DB108 WL User Manual 1. OVERVIEW 1.1 ABOUT ADSL An ADSL MODEM is a broadband Internet access device，which utilizes the high frequency segment of the phone line to transmit high-speed data without affecting the voice transmission. The frequency of the ADSL signal is higher than that of voice, so voice and ADSL signal can coexist in the same line and can be insulated in user side with a splitter. ADSL data transfer adapts the asymmetry model.
Atrie DB108 WL User Manual ⑸Power Interface: 11VDC，700mA. ⑹Ethernet Interface: With twisted cable connect to PC or HUB. Connect to PC through straight-through network cable; connect to UP LINK port of HUB through the crossover cable. ⑺Usb Interface: Program upgrade. ⑻Line Interface: Connect with telephone line from CO (central office). ⑽Reset button: Reset the configuration to default. 1.3 PROTOCOLS The device supports ADSL protocols as bellows: 1. 2. 3. 4. 5.
Atrie DB108 WL User Manual 2. HARDWARE INSTALLATION AND BASIC SOFTWARE CONFIGURATION 2.1 SYSTEM REQUIREMENT (1) Network card (2) Wireless network card (option) 2.2 HARDWARE INSTALLATION 2.2.1 BASIC CONNECTTION Figure 2.1 For using the Splitter to surf on the Internet and to make phone calls simultaneously, please refer to Appendix B: SPLITTER CONNECTION. 2.2.2 INSTALLATION STEPS 1. Connect ADSL MODEM line port ⑻with telephone socket with phone cord coming with the modem. 2.
Atrie DB108 WL User Manual 2.3 SOFTWARE CONFIGURATION 2.3.1 PREPARATION FOR SOFTWARE INSTALLATION Before installation, please consult ADSL service provider for parameters. Table 2.1 shows all the information needed to configure according to different protocols. Table 2.
Atrie DB108 WL User Manual 2.3.4 ADSL MODEM WORKING MODE CONFIGURATION 1． According to the different protocols, Users set ADSL Modem as bellows: Table 2.
Atrie DB108 WL User Manual Figure 2.4 2． SSID (Service Set Identifier): the mobile users cannot access WLAN until setting their SSID as the same value of the modem. The SSID value of the modem is “default” 3． Channel：to denote the different frequency of wireless signals whose value is from 1 to 13. The default value is”6”. If there are more than one APs located in the same area, each of them must works at different channels to reduce interference.
Atrie DB108 WL User Manual PVC 4 14 24 PVC 5 0 100 The default configuration is “1483 Bridged LLC” encapsulation，If you only want this mode，there is no need to modify it. But if you want the routed mode（for example PPPoE、PPPoA、1483routed） ，the other PVC must be closed in advance. Otherwise you must set the “NAT” to “Dynamic NAPT” to realize the same function (Refer to 3.2 for detail.).
Atrie DB108 WL User Manual 3. PROTOCOL CONFIGURATION Different protocols can be set in “WAN” 、 “LAN”、 “NAT”page. Click on the relevant anchor to enter the right page. 3.1 RFC1483 BRIDGED CONFIGURATION 1. WAN SETTINGS z Click “Wan” anchor in the left frame and select the virtual circuit in the left frame. Click “submit” button.
Atrie DB108 WL User Manual Click “NAT” anchor in the left frame and Set “NAT” item to“Disabled” in the right frame. Finally click “Submit” to save the configuration, which is shown as Figure 3.2. Figure 3.2 Click “Save Settings” button in the left frame and Click “Submit” in the right frame to save all above settings, which is shown as Figure 2.3. Then modem will restart automatically and run with new parameters. 3.
Atrie DB108 WL User Manual Figure 3.3 2． LAN SETTINGS Keep the configuration as default。 3． NAT SETTINGS Select “Dynamic NAPT” or “NAPT” as Figure 3.4 , then click “Submit” to save the settings。 Note: If you select “NAPT” you must close other PVCs. Refer to 2.3.6 for details. Figure 3.4 4． Click “Save Settings” button in the left frame and Click “Submit” in the right frame to save all above settings, which is shown as Figure 2.3. Then modem will restart automatically and run with new parameters.
Atrie DB108 WL User Manual 3.3 PPPoE/PPPoA CONFIGURATION There are two ways for PPPoE configuration: 1483 bridge plus third-party dial-up software and internal virtual dial-up. 1483 bridge plus third-party dialing software： z z z Set 1483 BRIDGE mode. Install “dial-up software” such as Enternet300, WinPoet and RasPPPoE. For more details please contact the DSL provider. Use the “dial-up software” to dial up.
Atrie DB108 WL User Manual Figure 3.5 2． LAN SETTINGS Keep the default configuration. 3． NAT SETTINGS Set “NAT” to “Dynamic NAPT” or “NAPT” which is shown as Figure 3.4 ,then click “Submit” to save the settings。 Note: If you select “NAPT” you must close other PVC. Refer to 2.3.6 for details. 4． Click “Save Settings” button in the left frame and Click “Submit” in the right frame to save all above settings, which is shown as Figure 2.3. Then modem will restart automatically and run with new parameters.
Atrie DB108 WL User Manual 4. DHCP FUNCTION Not only can be used as an ADSL Modem, it also has routing and DHCP features, which are especially appropriate for small LAN such as cyber cafes or small companies. When it is used in LAN , the connection can be set as Figure 4.1： Figure 4.1 Router and proxy server are not always necessary in the LAN. You can use this device as the router and DHCP server. 4.1 1. 1. 2.
Atrie DB108 WL User Manual Figure 4.2 Click “Save Settings” button in the left frame and Click “Submit” in the right frame to save all above settings, which is shown as Figure 2.3. Then modem will restart automatically and run with new parameters.
Atrie DB108 WL User Manual 5. OTHER FUNCTIONS AND CONFIGURATION 5.1 BRIDGE FILTER 1. This function can block any MAC addresses through the modem. Steps: (1) Click “Bridge Filter” in the left frame and Set the “Enable Bridge filtering” to Yes . (2) Input “Source MAC address” that should be filtered. (3) Click the “Add” button Figure 5.1 2. Users can modify or delete the MAC addresses that have been inputted which is shown as Figure 5.2. Figure 5.
Atrie DB108 WL User Manual Note: The maximum addresses you can be blocked is four. Input MAC address in source MAC field means blocking the MAC address to connect another device or the device. Input MAC address in destination MAC field means blocking the MAC address to respond connection from other MAC address. Input source MAC and Destination MAC concurrently will be ignored 5.
Atrie DB108 WL User Manual Figure 5.4 5.3 IP ADDRESS AND PASSWORD 1． CONFIGURATION OF IP As a network device, it has its IP address and MAC address. The factory IP address is 192.168.1.1 and subnet mask is 255.255.255.0.User can modify these addresses in “LAN” Configuration page。 2. CONFIGURATION OF ADMINISTRATOR’S PASSWORD When login the setting page, the system request user to input username and password to validate access permission.
Atrie DB108 WL User Manual 6.SOFTWARE UPGRADE This device supports software upgrade. To get detailed information, please ask the associated manufacturer or agents. 7. RESET TO DEFAULT SETTING If you cannot log in configuration page (for example: you forget the password),you can use this method to reset the ADSL MODEM to the default configuration，Then you can log in with the default username and password。 Press the reset button that is shown as Figure 7.
Atrie DB108 WL User Manual 8. SPECIFICATION 8.1 POWER SUPPLY z Exterior power adapter z Input: 220VAC, 50Hz z Output：12VDC，700mA。 z Polarity： z Consumption: MAX 5W 8.2 DIMENSION z 184mm（Length）x145mm（Width）x41mm （Height） 8.3 WEIGHT z Weight：270 gram 8.4 STANDARDS z EMI/Immunity: FCC Part 15 Class B, CE Mark (EN55022 Class B/EN50082) z Safety Standard: UL，EN60950 z Communication: FCC Part 68, CYR21 z Electromagnetic: in accordance with FCC, ETSI and CISPR standard z IEEE 802.11b standard. 8.
Atrie DB108 WL User Manual A. Troubleshooting Phenomena The indicator of power supply is not on The indicator of PC is not on Solution 1. Make sure the connection of power supply is correct. 2. Make sure the switch of power supply is turned on. 3. Make sure the output of power supply is correct. 1. Check the connection of cable and network adapter. 2. Make sure that the correct cable is used. 3. Make sure the cable works fine by pinging the host IP address. 1.
Atrie DB108 WL User Manual 1． Make sure the problems list above are all eliminated; 2． Make sure the WLAN card in computer works well. Check the wireless mode is “infrastructure”; 3． Make sure that “wireless” is shown on the configuration page of the modem. Otherwise there should be hardware error for the Wireless mode can’t work modem. Please ask manufacturer to change a new modem. 4． Make sure the WLAN card of the computer has the same SSID as that of the modem; 5． Check the Security mode.
Atrie DB108 WL User Manual B. SPLITTER CONNECTION 1. Splitter 2. Connection Firstly, use a telephone cord to connect the LINE port of Splitter and the RJ-11 port on the wall. Then with another telephone cord connect the ADSL port of Splitter and the LINE port of ADSL Modem another telephone cord. Finally, with one more telephone cord to connect the telephone set and the phone port of the Splitter.
Atrie DB108 WL User Manual C. SHIPPING LIST Check the list of device as the following, if anything missing you should contact franchiser. Atrie Technology Pvt. Ltd. Corporate office: Atrie House, # 591,3rd Block, Koramangala, Bangalore -560 034 India Registered office: #B-121,Ground Floor ,Kalkaji, New Delhi – 110019 Regional office (West): #C/312,3rd Floor, Gokul Arcade, Vile Parle(E) Subhash Road,Mumbai - 400057 Email: contacts@atrieindia.com Web: http://www.atrieindia.
Atrie DB108 WL User Manual Please use the factory- recommended power supply.
