Installation Sheet

ManualsBrandsAtosa ManualsAppliances24 Inch Wide 124000 BTU 4 Burner Range with Oven

Gas Restaurant Ranges

Operating Instructions

For Models: ATO-2B24G, ATO-12G4B 36, ATO-4B12G, ATO-10B, ATO-24G2B, ATO-36G, ATO-6B24G,

ATO-24G6B, , ATO-4B36G, ATO-36G4B, ATO-2B48G, ATO-48G2B, ATO-4B, ATO-24G, ATO-6B

Before you begin, please read these instructions carefully to use this product correctly, to make the

product perform ideally, and to avoid hazards.

To Cook Nicely!

Summary of content (23 pages)

PAGE 1
To Cook Nicely! Gas Restaurant Ranges Operating Instructions For Models: ATO-2B24G, ATO-12G4B 36, ATO-4B12G, ATO-10B, ATO-24G2B, ATO-36G, ATO-6B24G, ATO-24G6B, , ATO-4B36G, ATO-36G4B, ATO-2B48G, ATO-48G2B, ATO-4B, ATO-24G, ATO-6B Before you begin, please read these instructions carefully to use this product correctly, to make the product perform ideally, and to avoid hazards.
PAGE 2
Dear customers and users： Thank you for purchasing our products. In order to be able to better use this product, please read these instructions carefully before any operation, and follow the guide, to avoid any unnecessary trouble during using. Please keep this instruction manual in a safe place for convenient reference and operation. This instruction manual is subject to any change without further notice, and the manufacturer reserves the right of final interpretation.
PAGE 3
Gas Restaurant Ranges The Installation, Operation and Maintenance Guide Contents 1. Safety Protection……………………………………………………3 2. Brief Introduction……………………………………………………3 3. Manufacturer's Authority and Responsibility……………………4 4. Parameter Specifications……………………………………………4 5. Transport and Storage…………………………………………………9 6. Installation and Debugging…………………………………………10 7. Safety Notices and Precautions……………………………………12 8. Operating Instructions…………………………………………… 13 9. Cleaning and Maintenance …………………………………………17 10.
PAGE 4
1、Safety Protection Please make sure that the operator is an authorized and licensed technician before you allow him/her to install and operate the products. Be sure to strictly follow this instruction guide during installation and using. The manufacturer is not responsible for any dangers or accidents caused by improper operation or maintenance. Do not store flammable or explosive objects around the product. Keep all flammable and explosive objects at a safe distance away from the product for normal use.
PAGE 5
3、Manufacture’s Authority and Responsibility Banning of all or partial transformation to the products without the manufacturer's explicit authorization.

PAGE 6

Number of burners H Gridd o le t U I O - p v S S l e H H a n A A t P P e E E s Nozzle No. and Per BTU B.T.U./h Griddle Model ATO-4B (NG) ATO-4B (LG) ATO-24G (NG) ATO-24G (LG) Gas Species and Intake manifold Hot pressure plates （in.W.C.

PAGE 7

③ Information of Gas Supply and Burner The minimum supplied gas pressure regulator is factory set at 5”Natural Gas W.C, and 10”L.P. Gas W.C. The external thread of product’s intake-tube is 3/4 inches. < Table 4> Number of Nozzle No. and Per BTU B.T.U/h burners H Gridd Griddle o le Gas Species t and Intake Total U I O Model manifold BTUB.T.U - Hot p v pressure ./h Oven S S plates l e UI（in.W.C.

PAGE 8

4.3、48 inch series： ①：Size and package parameter information Model ATO-8B (NG/LG) ATO-6B12G (NG/LG) ATO-12G6B (NG/LG) ATO-4B24G (NG/LG) ATO-24G4B (NG/LG) ATO-2B36G (NG/LG) ATO-36G2B (NG/LG) Overall Packing Oven dimensions(IN) size(IN) dimensions(IN) L x W x H LxWxH L x W x H 5 50 8 5 3 48*32 *56 8 8 3 8 *41 Griddle Number working Net Gross of area(IN) weight(Kg)weight(Kg) oven L x W none 2 255.5 327 5 8 2 272.

PAGE 9

ATO-8B (NG) ATO-8B (LG) ATO-6B12G (NG) ATO-12G6B (NG) ATO-6B12G (LG) ATO-12G6B (LG) ATO-4B24G (NG) ATO-24G4B (NG) ATO-4B24G (LG) ATO-24G4B (LG) ATO-2B36G (NG) ATO-36G2B (NG) ATO-2B36G (LG) ATO-36G2B (LG) Natural Gas 5 Propane 10 Natural Gas 5 Propane 10 Natural Gas 5 Propane 10 Natural Gas 5 Propane 10 NG45 25,000 LP54 23,000 NG45 NG42 27,000 LP52 27,000 NG42 NG45 21000 LP54 21000 NG45 NG44 24,000 LP53 24,000 NG44 25,000 27,000 21000 24,000 LP54 LP52 LP54 LP53 23,000 27,000 21000 24,00

PAGE 10

ATO-10B (NG/LG) ATO-8B12G (NG/LG) ATO-12G8B (NG/LG) ATO-6B24G (NG/LG) ATO-24G6B (NG/LG) ATO-4B36G (NG/LG) ATO-36G4B (NG/LG) ATO-2B48G (NG/LG) ATO-48G2B (NG/LG) none 2 305 380 5 8 2 327 407 5 8 2 333 408 5 8 2 345 416 5 8 2 355 430 12*20 5 8 62 24*20 5 3 60*32 *56 8 8 3 *41 8 1 26 *26*14 2 3 *41 8 36*20 48*20 ②：Information of Gas Supply and Burner The minimum supplied gas pressure regulator is factory set at 5”Natural Gas W.C, and 10”L.P. Gas W.C.

PAGE 11

ATO-8B12G (NG) ATO-12G8B (NG) ATO-8B12G (LG) ATO-12G8B (LG) ATO-6B24G (NG) ATO-24G6B (NG) ATO-6B24G (LG) ATO-24G6B (LG) ATO-4B36G (NG) ATO-36G4B (NG) ATO-4B36G (LG) ATO-36G4B (LG) ATO-2B48G (NG) ATO-48G2B (NG) ATO-2B48G (LG) ATO-48G2B (LG) Natural Gas 5 Propane 10 Natural Gas 5 Propane 10 Natural Gas 5 Propane 10 Natural Gas 5 Propane 10 NG45 NG42 NG45 NG39 25,000 27,000 21000 27,000 LP54 LP52 LP54 LP52 23,000 27,000 21000 27,000 NG45 NG42 NG45 NG39 25,000 27,000 21000 27,000

PAGE 12

6. Installation and Debugging Any erroneous installation, adjustment, refit, overhaul or maintenance may cause property damage or personal injury. The work shall be performed by authorized and licensed technicians, otherwise the manufacturer has the right not to provide warranty service; Only be installed in accordance with the local code. If no similar standard, you should conform to the National Fuel Gas Code, ANSI Z223.1/NFPA 54, the National Gas Installation Code, CSA-B149.1, or the L.P.

PAGE 13

corners of the charbroiled bottom, ensure sufficient space for ventilation; Adjustable stainless steel legs to make the equipment level, and get the same level with other series of the same stove; Please lift the equipment rather than drag if you need to move it; Please refer to P16“11. Schematic Diagram for Installation of Rear Panel” for the installation methods of rear panel. Supplied gas pressure regulator is factory set at 5”Natural Gas W.C, and 10”L.P. Gas W.

PAGE 14

●Unplug pressure gauge after you accomplish pressure testing, then install needle type pressure joint screw arbor. Important: must screw joint screw arbor, to prevent gas escape! 6.2 Debugging It’s very important to debug the new stove. Through the comprehensive system test of equipment, we can ensure function and safety performance of products. Discovering any potential problems before use (such as equipment’s placement, ventilation, operation, etc), can avoid costly losses. 7.

PAGE 15

cause fire, personal injury or even death; Do not use out of doors; Such appliance is used to cook, fry and bake the food and shall not be used for other purposes; The equipment does not contain any user-serviceable parts. Dealers or technicians will repair it.

PAGE 16

Figure 2 Figure 3 Figure 4 Figure 5 8.3 Lighting of normally open fire of stove 1. Align the OFF indicative line of thermostat valve knob to the arrow (Figure 5) to close the valve. 2. Open the underside face plate of oven (figure 6), thoroughly press the button at the front end of safety valve, and ignite the pilot fire by lighter with another hand simultaneously (figure 7 and figure 8). Do not loosen the button immediately after the pilot gas is ignited. Down-press it for 10 – 15 seconds.

PAGE 17

Figure 6 Figure 7 Figure 8 Figure 9 Figure 10 8.4 Ignition of main fire of oven After the normally open fire is ignited, open the main fire valve of safety valve, and press the thermostat valve knob to rotate to the position LOW counterclockwise (figure 9). At this moment, the oven burner is ignited. Rotate the thermostat valve knob counterclockwise continuously to the required temperature (figure 10) and the oven starts warming.

PAGE 18

8.6 Stove Operation Before using the stove for the first time, please use a mild detergent to wipe it clean. Do not use corrosive or abrasives detergent. Turn the burners on about 15-20 minutes before broiling for preheating, according to the cooking requirement to adjust the flame size. Notice: When first preheating, the furnace will smoke above.

PAGE 19

angle. Then, tighten the fastening screw bolt of damper to guarantee the appliance does not get loose. At last, reinstall the underside face plate of oven. ④Caution: Each burner damper has been adjusted before delivery (once air input), Normal use without adjustment but only switching gas. Adjust only by authorized and licensed technicians. 9.

PAGE 20

Recommended cleaning methods Items Body Methods Wipe it with a soft cloth and mild detergent; Times daily Turn off valves when not in use; Control panel Wipe panel and control valve knob with daily mild detergent. Pull out catch tray from front body until the equipment cools down. Use a cloth with cleaning agent to wipe unit Catch tray surface, wipe up residue. Reinstall Per use after cleaning.

PAGE 21

10. Troubleshooting

Problems Not lighting Ignite the pilot light but not the main fire Possible causes 1.Insufficient gas pressure in pipe 2.Nozzle occlusion 1.Insufficient gas pressure in pipe 2.The main fire nozzle occlusion 3.Gas control valves have problems 4.The pilot light and the main fire’s distance is too far Problem solving 1.Contact the local gas supply dept. 2.Dredge nozzle 1.Contact the local gas supply dept. 2.Dredge nozzle 3.Change gas control valves 4.

PAGE 22

Note 1、Pressure maintaining valve connects with air intake, must be installed by authorized and licensed technicians, to ensure interface tightness. 2、The pressure regulator(s) have connected, the maximum load of natural gas cannot exceed 6”, and of LP cannot exceed 12”. 3、Adjustment range of the pressure regulator(s) is 3”-6”for natural gas, and 5”-12”for L.P.. 11.

PAGE 23

Step III Step IV (Fasten the rear top plate (Fix the rear top plate with at the corresponding position of rear panel) rear panel by hexagon bolt) Step V Step VI ( Insert the assembled rear (Fix the assembled rear top plate into the panel with the stove body by self-tapping screw) corresponding position of stove body) - 22 -