We strive to ensure that our products are of the highest quality and free of manufacturing defects or missing parts. However, if you have any problems with your new product, DO NOT RETURN IT TO THE STORE, please contact us toll free @: 1-888-996-2729 FAX: 1-866-873-3535 gameroom@escaladesports.com Or write to: Escalade Sports Customer Service Department P.O. Box 889 Evansville IN 47706 Please have your model number when inquiring about parts.
IMPORTANT! READ EACH STEP IN THIS MANUAL BEFORE YOU BEGIN THE ASSEMBLY. TWO (2) ADU LTS ARE REQUIRED TO ASSEMBLE THIS ATOMIC SLAM DUNK PC BACKBOARD DOUBLE SHOOTOUT Tools Needed: Allen Wrench (provided) Wrench (provided) Phillips Screwdriver ! Make sure you understand the following tips before you begin to assemble your basketball shootout. 1.This game (with Mechanical Scoring Arm) can be played outdoors in dry weather - but must be stored indoors. 2.Tighten hardware as instructed. 3.
HARDWARE IDENTIFIER (To Scale) H1 - M6 x 20mm Allen Head Bolt (16 pc) H3 - M6 x 45mm Allen Head Bolt (2 pcs) H2 - M6 x 35mm Allen Head Bolt (1 pc) H4 - M6 x 50mm Allen Head Bolt (10 pcs) H6 - M6 x 75mm Allen Head Bolt (8 pcs) H5 - M6 x 70mm Allen Head Bolt (6 pcs) H7 - M6 Flat Washer (70 pcs) H8- M6 Plastic Flat Washer (14 pcs) H9 - M6 Lock Nut (43 pcs) H10 - Plastic Bushing (8 pcs) (Not to Scale) (Packed in with Scorer Box) (Not to Scale) H11 - 3.
PARTS IDENTIFIER (Not to Scale) P2 - Middle Back Upright Tube (2) P1 - Upper Tube (2) P3 - Left Lower Back Upright Tube (1) P4 - Right Lower Back Upright Tube (1) P5 - Left Back Bottom Support Tube (1) P6 - Right Back Bottom Support Tube (1) P7 - Front Support Tube (2) P8 - Front Upright Tube (2) P9 - Left Top Connect Tube (1) P10 - Right Top Connect Tube (1) P11 - Bottom Connect Tube (2) P12 - Connect Tube (4) P13 - Base Upright Tube (2) All RIghts Reserved.
PARTS IDENTIFIER (Not to Scale) P14 - Front U-Tube (1) P15 - Long Support Tube (3) P16 - Short Support Tube (2) P17 - PC Backboard (1) P20 - Rim Support Plate (2) P18 - Rim (2) P21 - Electronic Scorer Display (1) P22 - Electronic Scorer Face Plate (1) P19 - Rim Net (2) P23 - Mechanical Scoring Arm (2) ACCESORY IDENTIFIER (Not to Scale) P24 - Ramp Chute (1) All RIghts Reserved.
Remove all the parts from the box and verify that you have all of the listed parts as shown on the Parts List. PARTS REQUIRED: 2 pcs - P2 Middle Back Upright Tube 2 pcs - P7 Front Support Tube 1 pc - P3 Left Lower Back Upright Tube 2 pcs - P8 Front Upright Tube 1 pc - P4 Right Lower Back Upright Tube STEP 1 Connect P3 - Left and P4 - Right Lower Back Upright Tube to P2 - Middle Back Upright Tube using Spring Lock as shown in FIGURE 1.
PARTS REQUIRED: 1 pc - P5 Left Back Bottom Support Tube 1 pc - P6 Right Back Bottom Support Tube STEP 2 Slide P6 - Right Back Bottom Support Tube to P5 - Left Back Bottom Support Tube as shown in FIGURE 2. P5 P6 FIGURE 2 PARTS REQUIRED: 1 pc - P9 Left Top Connect Tube 2 pcs - P11 Bottom Connect Tube 1 pc - P10 Right Top Connect Tube 4 pcs - P12 Connect Tube STEP 3 Connect P12 - Connect Tubes to P9 - Left and P10 - Right Top Connect Tube using Spring Lock as shown in FIGURE 3.
PARTS REQUIRED: 8 pcs - H4 M6 x 50 mm Allen Head Bolt 1 pc - P15 Long Support Tube 2 pcs - H5 M6 x 70 mm Allen Head Bolt 1 pc - T1 Allen Wrench 20 pcs - H7 Flat Washer 1 pc - T2 Wrench 10 pcs - H9 Lock Nut STEP 4 Attach P5/P6 - Back Bottom Support Tube to P3/P4 Lower Back Upright Tube using H5 Bolts, H7 Washers and H9 Lock Nuts as shown in FIGURE 4 and DETAIL A. Do not tighten H5 Bolts on this step.
PARTS REQUIRED: 1 pc - H2 M6 x 35 mm Allen Head Bolt 1 pc - P15 Long Support Tube 2 pcs - H4 M6 x 50 mm Allen Head Bolt 1 pc - P16 Short Support Tube 6 pcs - H7 Flat Washer 1 pc - T1 Allen Wrench 3 pcs - H9 Lock Nut 1 pc - T2 Wrench STEP 5 Attach P15 - Long and P16 - Short Support Tubes to P2 - Middle Back Upright Tubes using H4 Bolts, H7 Washers and H9 Lock Nuts as shown in FIGURE 5, DETAIL D and DETAIL E. Do not tighten H4 Bolts on this step.
PARTS REQUIRED: 2 pcs - P1 Upper Tube 2 pcs - P13 Base Upright Tube 1 pc - P14 Front U-Tube P1 STEP 6 Attach P1 - Upper Tubes to P2 - Middle Back Upright Tubes as shown in FIGURE 6. P2 P1 Attach P13 - Base Upright Tubes to P14 - Front U-Tube as shown in FIGURE 6. P2 FIGURE 6 P14 P13 P13 All RIghts Reserved.
PARTS REQUIRED: 4 pcs - H6 M6 x 75 mm Allen Head Bolt 4 pcs - H10 Plastic Bushing 6 pcs - H7 Flat Washer 2 pcs - P25 Locking Pin 4 pcs - H9 Lock Nut 1 pc - T1 Allen Wrench 1 pc - T2 Wrench STEP 7 Attach P9/P12 assembly tube and P10/P12 assembly tube from STEP 3 to P8 - Front Upright Tubes using H6 Bolts, P25 Locking Pins, H10 Plastic Bushings, H7 Flat Washers and H9 Lock Nuts as shown in FIGURE 7, DETAIL G and DETAIL H.
PARTS REQUIRED: 16 pcs - H1 M6 x 20 mm Allen Head Bolt 2 pcs - P18 Rim 24 pcs - H7 Flat Washer 2 pcs - P20 Rim Support Plate 8 pcs - H8 Plastic Flat Washer 2 pcs - P23 Mechanical Scoring Arm 16 pcs - H9 Lock Nut 1 pc - T1 Allen Wrench 1 pc - P17 Backboard 1 pc - T2 Wrench NOTE: Use P20 Rim Support Plate for P18 Rim only. STEP 8 Attach P18 Rims and P20 Rim Support Plates to the P17 Backboard using H1 Bolts, H7 Washers and H9 Lock Nuts as shown in FIGURE 8.
PARTS REQUIRED: 2 pcs - H3 M6 x 45 mm Allen Head Bolt 4 pcs - H10 Plastic Bushing 4 pcs - H6 M6 x 75 mm Allen Head Bolt 1 pc - P15 Long Support Tube 12 pcs - H7 Flat Washer 1 pc - P24 Ramp Chute 6 pcs - H9 Lock Nut 1 pc - T1 Allen Wrench 1 pc - T2 Wrench STEP 10 Slide elastic loop and sleeve of P24 Ramp Chute onto the P1 - Upper Tube as shown in FIGURE 10 and DETAIL I. Slide P13/14 Tube assembly into the front sleeve of P24 Ramp Chute as shown in FIGURE 10 and DETAIL J.
PARTS REQUIRED: 4 pcs - H5 M6 x 70 mm Allen Head Bolt 2 pcs - H7 Flat Washer 6 pcs - H8 Plastic Flat Washer 4 pcs - H9 Lock Nut 1 pc - T1 Allen Wrench 1 pc - T2 Wrench STEP 11 With the help of another adult, Attach P17 Backboard to P1 - Upper Tube using H5 Bolts, H8 Plastic Washers, H7 Flat Washers and H9 Lock Nuts as shown in FIGURE 11 and DETAIL M.
STEP 12 Connect P23 Mechanical Scoring Arm sensor wires to P21 Electronic Scorer as shown in FIGURE 12. Secure Elastic Loops from P24 Ramp Chute to the back of P17 Backboard as shown in FIGURE 12. Insert 3(three) pieces “AA” batteries at the backside of electronic scoreboard. Plug the mechanical scoring arm plug into backside of the electronic scoreboard. Press on/off button at the bottom backside of the electronic scoreboard to play and stop the game. Turn off P21 Electronic Scorer when not in use.
Congratulations! You have now assembled your Double Shootout. Please note the Care and Use instructions below. CARE AND USE OF YOUR SHOOTOUT 1. Product can be used OUTDOORS - but must be stored INDOORS. 2. DO NOT sit, climb or lean on the unit. 3. DO NOT drag the unit when moving it, This will damage the legs. 4. DO NOT place backside of this product against wall as during play, the backside of product could become damaged or your wall could become damaged.
First Time Battery Installation: Locate battery compartment for this product . Use alkaline batteries for maximum performance . Using a small Philips head screwdriver – loosen and remove the battery compartment cover screw(s). Remove battery compartment cover . Install new batteries only after reading the “ Battery Information NOTICE“ ! Replace compartment cover and secure cover with the cover screw . Do not over tighten and strip out the screw .
90 DAY LIMITED WARRANTY This consumer warranty extends to the original consumer purchase of any ESCALADESPORTS Product (hereinafter referred as the "Product"). WARRANTY DURATION: This Product is warranted to the original consumer purchase of a period of 90 days from the original purchase.
