Quick Start Guide

Atom 3D Printer
Quick-start Guide
UNPACKING AND PRINTER SETUP
1
AUTO-LEVELING
2
SAFETY NOTICE
4
FIRST PRINT
3
Use the minimum amount of
force required to affix the
sensor to the nozzle. If the
nozzle is touching the plastic
membrane, it may prematurely
trigger the switch.
Atom 3.5
Keep body parts
away from moving
fan blades!
Caution!
Keep away from hot parts!
Keep body parts away from
moving parts!
Perform the following steps to prepare the printer for use.
Remove the printer from its packaging and place it on a flat, stable
surface with plenty of ventilation and a nearby AC power outlet.
1.
Mount the Control Arms and Effector, making sure not to detach any of the arms
to preserve their magnetic orientation. NOTE: Each arm has a mark on the
magnet at one end indicating the north pole. The unmarked end indicates the
south pole. If the effector or arms become dismounted, reconnect the arms’ poles
to the their corresponding ball joints as illustrated.
2.
Assemble the Filament Bar.
3.
Plug in and power on.
4.
Contact
[e-mail] / [e-mail]
Confirm that the hotend is
at room temperature, and
that the target tempertature
is at 0
*Tapping the hotend icon
toggles between preheating
and cooling down.
**Nozzle 2 is only
showed on Dual Nozzle
Machine
1.
Install the Auto-level Sensor and connect the wire.
2.
Tap the Control icon and
then tap the leveling icon.
3.
4. Once the process has
finished and the machine has
returned to the home position,
remove the Auto-level Sensor.
Once the nozzle reaches the
target temperature, return to
the control menu, tap on the
Marco icon.
3.
Tap “Load Filament”
4.
Thread the included Monoprice PLA filament as illustrated.
1.
Green Wire
from Effector
Wire Harness
Auto-level
Sensor Wire
Load the filament to a point
within the circle as indicated
above.
The Filament
Sensor may be hung
from its holder when
not in use.
When upload has finished
Click the file name, then click yes to start print.
6.
For calibration prints, slicing
software and profiles, support,
and more, please visit the Sup-
port page.
8.
In case the first layer is not
sticking well to the build plate
(too high), or not extruding
any plastic at all (too low),
tap the control icon for
advanced settings to adjust
the Z-offset on the fly.
７.
Fan faces forward.
N
S
N
S
N
S
[＋0. 0 2 m m] Increase the offset
[-0.02mm] Decrease the offset
Atom Website
www.atom3dp.com
1
2
1
2
Return to the main menu, tap
on “Nozzle 1” icon
2.
Connect to your WiFi before your first print
WiFi： 802.11 b/g/n 2.4 GHz
Tap [Control] > [Console], tap on the [keyboard icon]
then type in the following code in order manually
5.
Click on
then click to upload G-code files.
IP address will be
showed
（in this case is
192.168.0.107）
5.
1.M552 S0
2.M587 S”SSID” P”Password”
3.M552 S1
1
2
Do not use this product near water, for example, in a wet basement or near swimming
pool or in an area where accidentenal contact with water or liquid might occur.
Avoid using this product during an electrical storm. There may be a remote risk of
electric shock from the surge casued by lightning.
The external power adapter or AC power cord is the equipment's disconnection
device. The power outlet must be located nearby the equipment and its access must
be easy.
Use this product in a well ventilated area.
FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE
STATEMENT
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment generates, uses and can radiate radio frequency energy and,
if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.-Increase the separation between
the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
-Consult the dealer or an experienced radio/ TV technician for help.
CAUTION:
Any changes or modifications not expressly approved by the grantee of this
device could void the user's authority to operate the equipment.
RF Exposure warningThis equipment must be installed and operated in
accordance with provided instructions and the antenna(s) used for this trans-
mitter must be installed to provide a separation distance of at least 20 cm
from all persons and must not be co-located or operating in conjunction with
any other antenna or transmitter. End-users and installers must be provide
with antenna installation instructions and transmitter operating conditions for
satisfying RF exposure compliance.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
Then connect to the IP address with any device: