Atlona HDMI 8 by 8 Matrix Switcher over CAT5e/6/7 AT-PRO2HD88M User Manual Revision 2: Firmware 1.1.16 atlona.
Table of Contents 1. Introduction .................................................................................... 3 2. Package Contents .................................................................................... 3 3. Features .................................................................................... 3 4. Before You Start .................................................................................... 4 5. Specifications .......................................
Introduction Extend HDMI and DVI (with HDMI to DVI adapter ex. AT-14040) sources up to 330ft at 1080p or 1920x1200. The Atlona HDMI 8 by 8 Matrix Switcher over CAT5e/6/7 allows for effortless control of up to 16 devices through IR remote control, RS-232, 3rd party IR controllers and the front panel. With stereo audio embedding combine stereo audio with DVI signals over one CAT5e/6/7 cable. To ensure all audio passes through the 8 by 8 Matrix Switcher supports all Lossy and Lossless formats of Dolby and DTS.
Before You Start • Make sure when connecting the CAT5e/6/7 cables a 568B termination method is used. • Avoid using patch panels and wall plates during initial set up and testing of the matrix switcher. • Make sure the matrix is connected to a component surge suppressor and line conditioner. Note: Atlona’s warranty does not cover damage due to electrical disturbances. A component surge suppressor and line conditioner are highly suggested especially in areas with electrical storms.
Panel Description Front Panel 2 1 5 3 4 7 8 6 a b c d e f g 1. Power Indicators. Red LED will light up when using main or backup power supply. 2. IR Receiver Window. Receives the signal from the included IR Remote Control or a 3rd party IR Controller. 3. Power Indicator. The light will illuminate red when the Matrix is in standby mode or green when the matrix is on. 4. Power Button. Cycles the power between on or off (standby) mode. 5. Enter Button.
Back Panel 1 2 6 3 7 8 4 9 10 5 11 1. Matrix IR IN - Used to control matrix I/O switching from a 3rd party IR controller. 2. Matrix IR Out - Global output, combines IR for all discrete IR output ports. 3. Firmware Update - Type B USB Port used for updating the matrix firmware only 4. RS-232 - Connect to this port for control from a computer or 3rd party controller. 5. Main Power - Plug included 24V/6.25A DC adaptor to power the matrix switcher 6. Audio Input Ports - 3.
Connection and Installation 3rd Party Controller Set Up Note: 3.5mm 3 conductor (stereo) cables are not compatible. Please use 2 conductor (mono) IR cables with IR input ports. Important: When using a 3rd party IR controller remember to connect a mono to mono 2 conductor IR extender cable into the matrix IR IN port for IR control of the matrix switcher I/O.
IR Remote Control Set Up Note: When using an IR remote control all sources can be controlled as well as the local display. Satellite Receiver IR Emitter IR Emitter AT-PWUSB-L AT-PRO2HDREC Blu-ray Player AT-PWUSB-L AT-PRO2HDREC-DA Optional USB power Optional USB power Amp IR Receiver Module IR Receiver Module Video Display Video Display IR Remote atlona.
Matrix Front Panel Functions The AT-PRO2HD88M’s front panel has 3 functions: I/O control, EDID set up, and matrix settings. The following sections go over step by step control.
EDID Set Up When the matrix is completely connected and turned on it will load the default EDID, which is the highest common native resolution of the devices. (i.e. With devices connected that range from 720p, 1080p, 2 channel audio, multi-channel audio and 3D, the default resolution will be 720p. Multi-channel audio and 3D are not available on default unless all devices have these features.) There are two options when setting up EDID: Default and Copy.
Matrix Settings When installing or troubleshooting it’s important to verify settings, or be able to come back to a project and see how it was set up. The AT-PRO2HD88M has matrix settings viewable through the front panel. View current I/O settings, firmware version, and the baud rates of not just the matrix but extenders as well.
RS-232 Connection RS-232 is connected through a 9-pin female D connector. The pins will have functions associated with them, some will be unassigned. 5 4 3 2 1 9 8 7 6 Command No. Pin Function 1 2 3 4 5 6 7 8 9 ---Tx Rx ---Gnd ------------- Not used Transmit Receive Not used Ground Not used Not used Not used Not used The command codes are very sensitive, do not change capitalization, spacing, or lettering.
RS-232 Set Up To set up the RS-232 hyperterminal (if not using 3rd party software) the first thing needed is to find the RS-232 communications port under the computer’s device manager. Once there right click the port and select properties. Under the properties menu select the port settings tab and update the menu to the matrix default: Bits Per Second: 115200, Data Bits: 8, Parity: None, Stop Bits: 1 and Flow Control: None. Baud Rate To change the baud rate of the matrix or the receivers (i.e.
RS-232 Command for the Output baud rate status RS232para The RS-232 status command will provide feedback for the current parameters for each output. Example: (See example of feedback below) RS232para Current RS232 parameter: - Port 1 :BaudRate 2400bps, DataBits 0, Parity None, StopBits 1. - Port 2 :BaudRate 9600bps, DataBits 0, Parity ODD, StopBits 1. - Port 3 :BaudRate 9600bps, DataBits 0, Parity None, StopBits 1. - Port 4 :BaudRate 9600bps, DataBits 0, Parity None, StopBits 1.
Updating and Resetting Updating firmware At times there will be new firmware to update, fix, or change functionality of products. Atlona has made this as easy as possible for updating on the job by simply downloading from Atlona.com and uploading the file onto the matrix. NOTE: Only use a Windows computer to update the matrix. Use of an Apple computer to update will cause the matrix to be unusable until the update is redone with a Windows computer.
Safety Information Safeguards To reduce the risk of electric shock, do not expose this product to rain or moisture Do not modify the wall plug. Doing so will void the warranty and safety features. If the wall plug does not fit into your local power socket, hire an electrician to replace your obsolete socket. This equipment should be installed near the socket outlet and the device should be easily accessible in the case it requires disconnection.
Warranty Limited Warranty Atlona Technologies warrants that (a) its products (AT-PRO2HD88M) will perform substantially in accordance with the accompanying written materials for a period of 3 years from the date of receipt and (b) that the product will be free from defects in materials and workmanship under normal use and service for a period of 3 years. In the event applicable law imposes any implied warranties, the implied warranty period is limited to 3 years from the date of receipt.
Atlona Product Registration Thank you for purchasing this Atlona product. - We hope you enjoy it and will take an extra few moments to register your new purchase. Registration creates an ownership record if your product is lost or stolen and helps ensure you’ll receive notification of performance issues and firmware updates. At Atlona we respect and protect your privacy, assuring you that your registration information is completely secure.
