Owner’s Manual AP-S20RT AC Distribution & Suppressor Unit AP-S20RT AC Power Distribution & AC Suppressor Unit with Remote Activation 1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A. Telephone: 800.876.3333 • Fax: 800.765.3435 –1– Specifications are subject to change without notice. AtlasSound.
AP-S20RT AC Distribution & Suppressor Unit Owner’s Manual Table of Contents Important Safety Instructions................................................................................................................... 3 Introduction ............................................................................................................................................ 5 Key Features and Applications......................................................................................................
Owner’s Manual AP-S20RT AC Distribution & Suppressor Unit Important Safety Instructions The lightning flash with arrowhead symbol within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage “ within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
AP-S20RT AC Distribution & Suppressor Unit • • • • • • • • • • • Owner’s Manual WARNING When The Device Is In Use To prevent electric shock, do not remove the product cover as there are high voltage components inside. Refer all servicing to Atlas Sound. Should any of the following irregularities occur during use, immediately switch off the power, disconnect the power cord from the AC outlet and contact Atlas Sound.
Owner’s Manual AP-S20RT AC Distribution & Suppressor Unit Introduction Thank you for purchasing the Atlas Power AP-S20RT AC Distribution and Suppressor Unit. The AP-S20RT has been designed to meet most installation requirements for AC power distribution and equipment power protection. To light your rack, the AP-S20RT incorporates a front panel USB port for lighting and equipment charging. The rear of the rack can be illuminated by the optional AP-GNL18 gooseneck LED lamp connected via an XLR style socket.
AP-S20RT AC Distribution & Suppressor Unit Owner’s Manual Key Features • 9 Total Outlets • 6 Rear Panel Switched Outlets • 2 Rear Panel Unswitched Outlets • 1 Front Panel Unswitched Convenience Outlet • Remote Activation via Latched Dry Contact Closure or DC Voltage • Remote Status LED Power Terminals • Rear Mounted Remote Activation Bypass Switch • EPD (Emergency Power Down) to Incorporate With Fire Control Panels • EVS (Extreme Voltage Shutdown) Clamping Spike & Surge Suppression Circui
AP-S20RT AC Distribution & Suppressor Unit Owner’s Manual Front Panel 1 2 3 5 6 7 4 1. Unswitched AC Outlet The 120VAC outlet is always live when the AP-S20RT power cord is plugged into an AC mains power source and voltage is present. Note: The AC mains power switch does not affect the Unswitched AC Outlet but it is protected with surge protection circuitry. 2. AC Mains Breaker The 20A rated breaker will open if the combined draw of all AC outlets exceeds 20A.
AP-S20RT AC Distribution & Suppressor Unit Owner’s Manual Rear Panel Features 5 4 3 2 1 1. AC Mains Input Connect the 14 Gauge 9' (3m) power cord to a 20A 120VAC outlet to provide power to the AP-S20RT. 2. AC Power Outlets These six outlets are “Live” when the front panel power switch is activated. The two Unswitched Outlets are always live if the power cord is connected to 120VAC. 3. XLR Light Socket A 12VDC XLR light socket provides power for the optional AL-GNL18 light. 4.
Owner’s Manual AP-S20RT AC Distribution & Suppressor Unit Installation Before installing, it is recommended to read the entire manual to ensure proper operation and that all features are being utilized. The AP-S20RT can be placed on a shelf or rack mounted in a standard 19" width rack. When rack mounted, placement within the rack is flexible however the AP-S20RT should be within 6' of a dedicated 20A AC outlet. When rack mounting, use Rack Rail type screws of 10 ⁄32" x 1".
AP-S20RT AC Distribution & Suppressor Unit Owner’s Manual AC Power Cord Retainer System Your Atlas Power product comes with an AC Mains Power Cord Retainer System. This system prevents the power cord from being removed without the use of a screwdriver. Follow these steps for installation. Note: Installation of this product must be done by a certified electrician. 1. Locate the 6/32 screw, retainer clip, and zip tie. 2. Locate the AC wall outlet that will be used to power the Atlas Power product.
AP-S20RT AC Distribution & Suppressor Unit Owner’s Manual Specifications Type Power Conditioner & Suppressor Load Rating 20A Safety Listings ETL (UL 60065 Standard) Front Panel Outlets 1 Unswitched USB Port 1 USB Charge/Light Port (5VDC, 1A) Activation Switch Rocker Circuit Breaker 20A Resettable Indicators AC Power On, AC Fault, EVS Protect Rear Panel AC Outlets 8 Outlets Total LED Light Socket XLR Socket to Provide 12VDC for Optional AL-GNL18 Gooseneck Lamp LED Light Switch
AP-S20RT AC Distribution & Suppressor Unit Owner’s Manual Limited Warranty All products manufactured by Atlas Sound are warranted to the original dealer/installer, industrial or commercial purchaser to be free from defects in material and workmanship and to be in compliance with our published specifications, if any.
