Safety Information

Safety Information IL-R V1
4
© Atlas Copco Industrial Technique AB - 9839 1630 00
Authorities can request relevant technical information from:
Product Compliance Manager, Atlas Copco Industrial Tech-
nique AB, S-105 23 Stockholm Sweden
Stockholm, 20 November 2018
Carl von Schantz, Managing Director
Signature of issuer
WEEE
Information concerning Waste of Electrical and Electronic
Equipment (WEEE):
This product and its information, meets the requirements of
the WEEE Directive (2012/19/EU), and must be handled in
compliance with the directive.
The product is marked with this symbol:
Products with the symbol of a crossed out wheelie bin with a
single black line underneath, indicates that parts within the
product must be handled in compliance with the WEEE Di-
rective. The entire product, or the WEEE parts, can be sent to
your “Customer Centre” for handling.
FCC and ISED Compliance Statement
FCC ID: 2AQ8P-ILR1
ISED certification number: 24224-ILR1
This device complies with: CAN ICES-3 (B)/NMB-3(B)
This device complies with part 15 of the FCC Rules. Opera-
tion is subject to the following two conditions: (1) This de-
vice may not cause harmful interference, and (2) this device
must accept any interference received, including interference
that may cause undesired operation.
Changes to the IL-R V1 module and / or it’s firmware, in-
cluding but not limited to modifications to the UWB antenna
configuration and / or the UWB antenna, voids the user’s au-
thority to operate the device. The device is in compliance
with the requirement for RF exposure in the US with 20 cm
separation distance between the user and the device. The an-
tenna is fixed to the device and no change in antenna or fixa-
tion of the antenna is acceptable and such modification is
considered to violate the Compliance Statement.
NOTE: This equipment has been tested and found to
comply with the limits for a Class B digital device, pur-
suant to part 15 of the FCC Rules. These limits are de-
signed to provide reasonable protection against harmful
interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the in-
structions, may cause harmful interference to radio com-
munications. However, there is no guarantee that inter-
ference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or
television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the follow-
ing measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is con-
nected.
• Consult the dealer or an experienced radio/TV tech-
nician for help.
This equipment may only be operated indoors. Operation
outdoors is in violation of 47 U.S.C. 301 and could subject
the operator to serious legal penalties.
Labeling Requirements for End Product
For an end product using this IL-R module there must be a
label containing, at least, the following information:
This device contains
FCC ID: 2AQ8P-ILR1
IC: 24224-ILR1
The label must be affixed on an exterior surface of the end
product such that it will be visible upon inspection in compli-
ance with the modular approval guidelines developed by the
FCC.
In accordance with 47 CFR § 15.19 the end product shall
bear the following statement in a conspicuous location on the
device:
"This device complies with Part 15 of the FCC Rules. Opera-
tion is subject to the following two conditions;
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, includ-
ing interference that may cause undesired operation."
When the device is so small or for such use that it is not prac-
ticable to place the statement above on it, the information
shall be placed in a prominent location in the instruction
manual or pamphlet supplied to the user or, alternatively,
shall be placed on the container in which the device is mar-
keted. In case, where the final product will be installed in lo-
cations where the end-user is not able to see the FCC ID and/
or this statement, the FCC ID and the statement shall also be
included in the end-product manual.
ISED Compliance Statement:
(English) This device complies with Industry Canada’s li-
cence-exempt RSSs. Operation is subject to the following
two conditions: