ITALIANO Questo prodotto è coperto da garanzia Atlantis On-Center della durata di 2 anni. Per maggiori dettagli in merito o per accedere alla documentazione completa in Italiano fare riferimento al sito www.atlantis-land.com. ENGLISH This product is covered by Atlantis 2 years On-Center warranty. For more detailed informations please refer to the web site www.atlantis-land.com. For more detailed instructions on configuring and using the Switch, please refer to the online manual.
INDEX 1. 1. Product Overview .......................................................................... 9 1.1 An Overview of the DiskMaster ..................................................... 9 1.1 System Requirements .................................................................10 1.2 Package contents .......................................................................10 1.3 Choosing a place for your DiskMaster ..........................................11 1.4 DiskMaster Application ...............
RAID Configuration...........................................................................47 RAID Alarm Settings .........................................................................49 2.6 SYSTEM->Power Management ....................................................50 System Reboot .................................................................................50 2.7 SYSTEM->Firmware Upgrade ......................................................51 Module Upgrade .....................................
APPENDIX E: MySQL Database ...............................................................89 Status 89 My.cnf Settings ................................................................................90 Logs 91 APPENDIX F: PostgreSQL Database ........................................................92 Status 92 Logs 93 APPENDIX G: DDNS...............................................................................95 Status 96 Settings 97 APPENDIX H: iTunes Server ...............................................
Copyright Statement No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, whether electronic, mechanical, photocopying, recording or otherwise without the prior writing of the publisher. Windows™ 98SE/2000/ME/XP/VIsta are trademarks of Microsoft® Corp. Pentium is trademark of Intel. All copyright reserved. The Atlantis logo is a registered trademark of Atlantis.
Limited Warranty Our warranties (for hardware and software) do not cover data loss – back up the contents of your drive to a separate storage medium on a regular basis . Also, consequential damages; incidental damages; and costs related to data recovery, removal and installation are not recoverable under our warranties. Safety Information Only qualified personnel should carry out technical work on the device.
Important information for the correct recycle/treatment procedures of this equipment The crossed-out wheeled bin symbol printed on the unit label or unit packaging indicates that this equipment must not be disposed of as unsorted municipal waste but it should be collected separately.
Thank you for purchasing the DiskMaster storage solution. With speed, ease of use, high capacity, and support for numerous applications, DiskMaster is the ideal solution for all of your data storage needs. 1. 1. Product Overview 1.
USBCopy allows to quickly back up data from an USB storage device (USB flash, USB card reader or USB HD) to DiskMaster with just one single touch. Apache/PHP/MySQL With built-in support for Apache/PHP/MySQL, users can can simply point your browser to your DiskMaster’s name (or IP address) to view your website. Doing away with the need to have a computer connected to it, and allowing you to share it with the rest of the users in the office or at home. 1.
1.3 Choosing a place for your DiskMaster When selecting a place to set up your Disk Array, be sure to follow these guidelines: Place on a flat and stable surface capable of supporting at least 5Kg. Place the DiskMaster close enough to a network jack for the Ethernet cable to reach it. Leave at least 10cm of space at the rear of the device for ventilation. Use a grounded wall outlet (uninterruptible online power supply with AVR is recommended.
1.
1.5 The Front LEDs and Rear Ports PORT/Button/LED 1 HDD A LEDs 2 HDD B LEDs 3 Power LED 4 Power Button 5 6 7 8 9 10 11 12 13 LAN LED USB I LED USB II LED Backup Button USB I Port Power DC Jack Gigabit LAN Port USB II Port Reset SW MEANING HDD A indicators. HDD B indicators. Power ON/OFF indicator. Power Button. Press the button and holds for 3 seconds to turn ON or turn OFF. Press the power switch to start/shutdown the DiskMaster.
defaults. After the device has turned on (turn on the power and wait 3 minutes), press and hold reset button for 5/10 seconds, then release it to reset it (this is used when you can not login to the DiskMaster, e.g. forgot the password. PWM Cooling FAN. Leave at least 10cm of space at the rear of the device for ventilation. Cool FAN There is a Reset button on the back of DiskMaster which will help return its IP, System ID, System Password and DHCP to their factory default values.
1.7 Default Settings The TCP/IP protocol stack and Ethernet network adapter must be installed. If not, please refer to MS Windows relative manuals. Before you configure this device you need to know the following default settings: Username: sysadmin Password: atlantis IP address: by DHCP, (If a DHCP server isn’t available in the network, the DiskMaster will use 192.168.1.251 and Subnet Mask 255.255.255.0). Server name: DiskMasterG502D DiskMaster saves all settings on formatted Hard Disk.
1.9 Building DiskMaster HDD System If the hard disks are being installed for the first time, you need to initialize the disks before you can use them. Follow the steps described below. To configure your DiskMaster, you will need to use the web browser, enter the IP address and then use the web configuration for further setup. To find out the IP address (if You changed) of your device once it is connected to the network, there are several different ways as described on the following pages.
Insert NAS system CD-Rom in to your computer, and run NasLink. Pressing the Refresh List button. NAS in the same subnet will automatically show up in the Device list. Make sure NAS system has probably connect to the network and search again. You might have to configure your firewall/Antivirus or even temporarily turn it off. If a DHCP server isn’t available in the network, the DiskMaster will use 192.168.1.251 and Subnet Mask 255.255.255.0.
When you first time login DiskMaster or System Disk hasn’t been created, you will be asking if you would like to do RAID configuration. Click Cancel, set HDDs as Normal with 2 distinctive storages. Click OK, set HDDs to RAID mode, RAID 0 or RAID 1.
There are 2 differents RAID mode: RAID 0: RAID 0, known as disk striping, has generally the best performance, but does not offer any redundancy. In this level, data is broken into small units called sectors, and sectors are distributed across all disks in the array. As it does not provide any data protection, if any disk in the array fails then all data in the array is lost. Such stripes allocation allows to enhance I/O performance.
There will two more items, Server and GUI options show in the left side box. At the right side, besides the basic DiskMaster information, there are two messages show the status of File Server (running) and FTP server (stopped). Detail System Disk information can be checked by clicking: System ->Hard disk Management -> Hard Disk Configuration There are 4 partitions in SYSTEM Hard Disk, /fsys, /data, reserved area and swap. When the settings are made, the DiskMaster system starts formatting the disks.
RAID Mode You need to install 2 HDDs to create RAID system on DiskMaster. When you first time login DiskMaster or System Disk hasn’t been created, you will be asking if you would like to do RAID configuration. Tap OK button on last dialogue box, the screen will display raid type selection as the picture below (or System ->Hard disk Management -> Hard Disk Configuration). Choose a proper RAID type you want to create on DiskMaster. RAID 0: Total capacity will be 2 times of the smaller HDD.
There will two more items, Server and GUI options show in the left side box. At the right side, besides the basic DiskMaster information, there are two messages show the status of File Server (running) and FTP server (stopped). Detail System Disk information can be checked by clicking: System ->Hard disk Management -> Hard Disk Configuration There are 4 partitions in SYSTEM Hard Disk, /fsys, /data, reserved area and swap. There is only one disk can be seen on the disk information.
1.10 Mapping a Network Drive Default SAMBA/FTP system account and password Factory Default ID: sysadmin Factory Default PW: atlantis The folder public is created and activated. A File Server supporting SMB/CIFS provides a shared storage on DiskMaster for users attached to the LAN. It is convenient to share all kinds of computer files on the LAN such as documents, sound/audio files, photographs, movies, images, database, etc.
Mapping a Network Drive in Windows Vista/7 Start->Computer Click on Map Network Drive. Follow the setup wizard and fill in the path to your DiskMasterG502D. Alternatively, you can also browse for the shares by clicking on the Browse button and locating the folder that way (choose public folders). Click on different user name and digit username and password (sysadmin, atlantis). Then click OK. Select Reconnect at Logon then click Finish.
2. WEB Configuration Open the web browser, enter the local port IP address of this device, which defaults at http://192.168.1.10, and click “Go”, a username and password window will appear. The default username & password are admin & admin, in respectively. To configure your DiskMaster, you will need to use the web brows enter the IP address and then use the web configuration for furth setup.
2. Advanced Web Configuration La configurazione del dispositivo può essere fatta esclusivamente via WEB. Lanciare il browser web e digitare http://Indirizzo ip:6666 Per conoscere questo indirizzo IP è possibile seguire una delle seguenti 3 strade: Se sulla rete non è presente un server DHCP, il DiskMaster si posizionerà sull’IP di default 192.168.1.251. Se sulla rete è presente un server DHCP, il DiskMaster prenderà da questo l’indirizzo IP.
Digitare username/password (syadmin e atlantis) e cliccare su Login.
La schermata principale, richiamabile cliccando su Home, mostra le seguenti informazioni: Kernel Version: Viene mostarta la release di Kernel utilizzata System Date: Viene mosytrata l’ora corrente Physical Address: Viene mostrato il Mac Address del DiskMaster HDD Space: Viene mostrato lo spazio libero e quello totale per le partizioni di dati e sistema.
2.1 SYSTEM->Networking Management NetWork Settings These settings help DiskMaster connect to the network IP Status: The default value is Automatically (DHCP). In this way the DiskMaster is configured as DHCP clients. Check the Manual Configuration to set the IP address manually. Host Name: While the name is changeable to administrator’s favorite, the use of “DiskMaster” can help you to memorize how you create your own FQDN (Fully Qualified Domain Name).
PPPoE Dial-up Setting If you are using an ADSL dial-up network connection with a dynamic IP,DiskMaster can also support ADSL dial-up connections. Enter the user name and password provided by the ISP to acquire an ADSL Dynamic IP.
2.2 SYSTEM->Account Management In this section you can define groups and users. The menù consists of four subtest: New Account/Account Listing New Group/Group Listing Before starting you should know the following limitations: Initial Letter: It can’t be a number, but only a character Use only characters, numbers and “_” Windows doesn’t recognize the difference between upper case and lowercase instead of machines based on Linux as DiskMaster. It’s recommended not to differentiate this account.
After entering the parameters click SAVE to make permanent the configuration. When the web server module is installed, you will see an additional option: Disable User’s Homepage. Checking this option will prevent users to access their homepage. When it creates a new user, the DiskMaster create in HOME a folder with the account’s name, and in this folder are created 2 subfolders public_html and nested cgi-bin. public_html: PHP or HTML content should be placed in this folder.
New Group In this section it is possible to create a new group. Type in the field Group the name of the new group. After entering the parameters click SAVE to make permanent the configuration. Groups should be created before the creation of the users. In this way they may be directly associated with the combo box to the group.
Account Listing In this section you can see and edit all existing accounts in DiskMaster. It’s possible to see, modify or cancel any account previously created. To reomve and account, simply tick the box on the left of the name (account) and then click on Delete. When an account il deleted, the corrisponding folder i salso deleted with its stored data. To modify an account click on the icon Edit ( ) at the corresponding row. You will see the same screen that appears when you create your account.
When the number of users created is very large, you can use the menù Search to restrict the listo f accounts displayed.
Group Listing In this section you can see and modify all the groups existing in the DiskMaster. To modify an account click on the icon Edit ( corresponding row. The screen below will appear. ) at the You can modify all the following fields: Group, Quota, Disable FTP/File Server, Homepage. Check Apply Settings if you modify the following fieldsi: Quota, Disable FTP/File Server, Homepage. Click Save to make permanent the configuration.
When the number of groups created is very large, you can use the menu Search to restrict the list of accounts displayed.
2.3 SYSTEM->Backup Management Throught this feature the DiskMaster can make a backup to a remote PC, another DiskMaster or any shared network folder. Files are encrypted and compressed in order to make the process safer and reduce transmission times. The menu consist of three sub-menu: Backup Server Setting Backup/Restore Schedule Backup Backup Server Setting IP or Host Name Setting: Enter the IP address where the shared folder resides. Shared Folder: Type the name of the folder.
You can make a local backup, the IP address must be 127.0.0.1. You are strongly advised to use another device to backup data. Backup/Restore When the “Backup Server Setting” is configured, you can perform instant Backups or Restore from the backed up file/folders. You can select what you want to backup, or check the Backup Items to make a full backup. Then click Backup. DiskMaster will create on the destination folder a folder with the following name “YYYY-MM_DD” with all files within the backup.
You can select what you want to restore, or check Backup Items to make a full backup. Select from the combo box Backup Date a date and click Restore. The restore of the field Network Management should be done alone to avoid IP configuration problems.
Schedule Backup In this section you can schedule backup processes. DiskMaster can also send an email to the administrator when the process has correctly finished. You can select what you want to backup, or check the Backup Items to make a full backup. In Schedule Settings you can determine the frequency of the operation. In Backup Quantity, through the combo box, you can determine how many copies left before being erased. Select ALL to leave all the copies.
2.4 SYSTEM->System Information In this section of DiskMaster are shown more information about hardware and information about the date of the device. The menu consist of two sub-menus: Hardware Info System Date Hardware Info The system shows information about memory and typology of configuration applied to discs.
System Date In this section you can configure the internal clock of DiskMaster. The DiskMaster will update the clock using the following rules: When turned on For each hour of operation At each change of the combo box Time Zone In Time Zone select from the combo-box, the time slot belongs. After entering the parameters click Save to make permanent configuration. The fields Date e Time (Date/Time) should be updated (after about a minute and if your internet connection is active).
2.5 SYSTEM->Hard Disk Management The File Server supports SMB/CIFS and allowcs to share folders on PC’s connected in LAN. It’s possible to share data files, music or video. The management system also allows you to control the access. The menu si composed by three sub-menus: Hard Disk Configuration: allow you to enable or disable status of file server. This service is enabled by default. RAID Configuration: allow you to set the names of Host Name, WorkGroup and Description field.
Hard Disk Configuration In this section you can have access to detailed configuration of the disc/discs. DiskMaster partition the disc in four different areas: /fsys Home Directory(/data) Reserved Swap 15 GB *The excess capacity is area 1 GB allocated to this partition 50 MB /fsys: This area stores the native modules and extensions, all accounts created and miscellaneous information (includind system settings). /data: Area used to store data. This partition is the only one to be remapped.
Identify the partition to replace in the Home, click Replace. DiskMaster will copy the contents of the Home Directory in the new partition. The original home directory will be changed into an ordinary partition.
RAID Configuration Before creating a RAID should verify that all partition are deleted. Delete with Delete all existing partitions (Hard Disk Management->Hard Disk Configuration). The disc structure must be like in the picture: When all partitions have been removed, you can create a RAID. Select the type and then click Save. When the processo f RAID creation will be completed a pop up window will be displayed.
To remove the RAID click Reset, in Hard Disk Management>Hard Disk Configuration. Although the configuration is RAID, shows a single disc (to the left of the word is highlighted RAID Disk).
RAID Alarm Settings Check the field Send Out Notices to allow the sending o fan e-mail in case of errors in RAID. After entering the parameters click Save to make permanent configuration. The mail address must be set GUI Management->System Info.
2.6 SYSTEM->Power Management System Reboot Click Save to reboot the system. All the services will be stopped and the system rebooted. Click Save, and then click OK to confirm to the requests in the following window, to start the rebooting process of DiskMaster.
2.7 SYSTEM->Firmware Upgrade Module Upgrade In this section it is possible to install aditional modules in DiskMaster or upgrade your Kernel. You can install additional packages on the device to expand its functionality. Native modules already installed on DiskMaster are: SYS: Is the Kernel of the system. WEBMIN: The interface used to control DiskMaster. SAMBA: The File Server. FTP: The FTP server.
It should be ensured during the entire phase of upgrades, the alimentation to the device. If this fail, the device may not be recoverable. Make the upgrade using a wired connection and not a wireless one. This could damage the device and void the warranty. Don’t use the restore files created with earlier version of the firmware. This might make the device unstable. During the upgrade process you should not close your web browser,load new pages or click on links.
2.8 SERVER->File Server The File Server supports SMB/CIFS and allows sharing of folders on PC’s connected in LAN. It’ s possible to share data files, music or video. The management system also allows you to control access. The menu in question consist of three sub-menus: Status: allows you to enable or disable status of file servers. This service is enabled by defaut. Settings: allows you to set the names of Host Name, WorkGroup and the field Description.
Settings You can set the name for the Service of File Server (Host Name), WorkGroup and the Description field. After entering the parameters click Save to make permanent the configuration.
Share Folders In this section you can create new folders, and enable them to decide access. DiskMaster creates the defautl public folder, entitled to all account to read/write. DiskMaster use the following structure for the creation/location of folders.
ftp_file: upload. Upload directory for FTP users with anonymous access.
To create a new shared folder follow the steps: Click NEW ( ), type in the field Folder Name the name of the shared folder and then in Description an alphanumeric identifier. Click the button NEW to finish. Before starting, you should know the following limitations: Lettera iniziale: can’t be a number, but only a character Use only characters, numbers and e “_” Windows doesn’t recognize the difference between upper case and lowercase instead of machines based on Linux as DiskMaster.
To delete a shared folder click on the button ( far right) of the folder itself. DiskMaster asks for confirmation. Click OK to continue. All files in it will be removed from the system. For mapping a network drive using the syntax: \ \ IP address \ FolderX , using the credentials you have created. For more details see the chapter in Section 1.12.
To configure access to a folder, once activated, click on the button of the folder itself. You will see the image below. (Far right) Folder Name: You can change the folder name here. Description: you can change the name. Permission Control: You can select the type of access allowed to users. Able to Browse: allows you to find the folder. Read Only: allows you to read the contents of the folder.
Invalid Accounts, it will be considerate as Invalid Accounts. Therefore in case of conflict: Invalid>Valid DiskMaster uses the following order of importance: Invalid>Valid-> Write>Read When you create a shared folder, you can redirect to a partition larger than the root partition.DiskMaster supports up to 4 folders redirected. This type exists only when you are not using RAID1/0 mode and the system has 2 hard disk.
2.9 SERVER->FTP Server The FTP service (File Transfer Protocol) allows transfer of files over the Internet or local LAN. The menu consists of four sub-test: Status: allows you to activate or deactivate the status of the FTP server. This service is not activated by default. Settings: Allows you to set the operating mode of the FTP server of DiskMaster. Anonymous Settings: Anonymous Settings: Set the FTP server anonymously. Logs: logs you can see this for details on using the FTP server..
Status The FTP Service is disabled by default. To enable service check FTP Server Start.When the service is active, you will see the screen below. It's possible to stop or restart the service by checking the appropriate box.
Settings Host Name: Enter the name of the FTP server. Listen Port: Generally, the listening port of the FTP server has the number 21. You can change that number but must be notified to the FTP client (and appropriately changed the Virtual Server section of the ADSL Router). Maximum number of Logins: Enter the maximum number of simultaneously active sessions. Each connection occupies 2 sessions (data and control).
Test1 is limited to uploads and downloads to 100KBs 400KBs. Upload Test2 is limited to 100KBs downloads but has no limits. Test 3 and Test4 have limits but not a download 400Kbs upload..
Anonymous Settings Anonymous login Allowed: Check to allow anonymous login. Maximum number of Logins: Enter the maximum number of simultaneously active sessions. Each connection occupies 2 sessions (data and control). Maximum Upload/Download Rate: It 's possible to limit the introduction of a value. A value of 0 implies no restriction and DiskMaster use all available bandwidth.
Logs The FTP server stores all activities that interest him. There are 2 types of log files.. Secure: stores information such as Date, Time, IP Address, User Name. Xferlog: stores all the activities made by a user as upload, download, delete, change etc ... A single file contains information about a week.. The file 1-4 respectively indicate (the current week, 2 weeks ago ...) Delete: Deletes the current log file. Download: allows you to download the current log file and save it elsewhere.
2.10 GUI->GUI Management In this section you can configure the GUI administration DiskMaster. The menu in question has 5 submenus: Password Settings: è You can change the user / password. Access Management: you can control access to the detailed configuration DiskMaster. System Info.Setup: Configuring notifications via email. Notice to Host: Configure the SMTP service. Logs: logs you can see this for details on using the FTP server.
Password Settings After Username: type your new username. default username is sysadmin. New Password: type your new password. The default password is atlantis. Confirm New Password: retype your new password. entering the parameters click Save to make permanent configuration.. After 5 failed login, DiskMaster wait a minute before accepting a new login attempts.
Access management Device Name: Type the name of the device. The default name is DiskMasterG502D. Enable SSL Connection: Check to enable encryption. To access the DiskMaster type https instead of http. Authorize Mode: If this option is not checked, the authentication is controlled dao computer's browser. If this option is checked nanny timed idle time (this is zero if the session is permanent) slaughtered and DiskMaster session will require a new login Terminal Service Option: Enable Telnet.
System Info.Setup Company(Org.)name: type identifier. Administrator name: type identifier. Administrator E-Mail: type the email address where the device sends alerts / messages. After entering the parameters click Save to make permanent configuration..
Notices to Host In this section you can configure the details to enable DiskMaster sending mail. Host: IPO type the address of the SMTP server and port used (usually 25). Need Authorization: check if the SMTP server requires authentication. Account Verification: Type the username. Password Verification: Type the password. Send a test Mail: click to send a test email (the address entered in the Administrator E-Mail System Info.Setup). After entering the parameters click Save to make permanent configuration.
Logs DiskMaster stores all activities that affect the GUI. There are two types of log files:. Miniserv.log: stores information such as date, time, IP address, Username and transactions. Miniserv.error: stores all abnormal activity, including attacks.. A single file contains information about a week. The file 1-4 respectively indicate (the current week, 2 weeks ago ...) Delete: Deletes the current log file. Download: allows you to download the current log file and save it elsewhere.
APPENDIX A: Troubleshooting This chapter covers potential problems and the corresponding remedies. A.1 Using LEDs to Diagnose Problems The LEDs are useful aides for finding possible problem causes. A.1.1 Power LED The PWR LED on the front panel does not light up. Steps Corrective Action 1 Make sure that the DiskMaster’s power adaptor is connected to the device and plugged in to an appropriate power source. Use only the supplied power adaptor.
3 Password: atlantis IP address: by DHCP, (If a DHCP server isn’t available in the network, the DiskMaster will use 192.168.1.251 and Subnet Mask 255.255.255.0). Server name: DiskMasterG502D It is highly recommended to change the default username and password. Make sure you store the username and password in a save place. A.3 WEB Interface I cannot access the web configurator. Steps Corrective Action 1 Make sure you are using Internet Explorer 7.0 and later versions.
sessions at the same time). 2. FTP Server: Maximum is able to create 32 users accounts, 8 users account connect at the same time, and maximum 16 folders shared by one account). 3. Samba Server: Share Level Access (maximum 16 folders shared by root). What is the protocol of network file sharing system using by DiskMaster? Steps Corrective Action 1 DiskMaster has the built-in Samba Server for file sharing, it is using SMB (Server Message Block) protocol to integrate TCP/IP, NETBUEI and IPX/SPX protocol.
APPENDIX B: Tips Before Installation Before installing DiskMaster , please be aware of some key information regarding DiskMaster which will help you understand this machine and further operation. 1. 3 Seconds Power ON/OFF control To avoid faulty power button operation: Power ON: Press the power button and hold for 3 seconds until the power LED turns on. Power OFF: Press the power button and hold for 3 seconds until the power LED turns off. 2.
HDD Mode HDD Total Capacity A B Normal 2TB 2TB 4TB RAID 0 1TB 1TB 2TB RAID 1 2TB 2TB 2TB Remark 2 separate HDDs are shown in the system. 2TB is the maximum in each HDD bay. 2 HDDs are combined as a single HDD (Stripping). The maximun capacity can not exceed 2TB. 2 HDDs are exact duplicates of each other (Mirroring). 7. Native Server/Service and Extension Server/Module DISKMASTER is equipped with two kinds of service, “Native” and “Extension”.
- 10. /fsys: This area stores system program including native and extenion modules, management data (i.e. user account), system settings information, etc… /data: General storage area which is controlled and used by the user. Reserved area: Reserved for future usage. Swap: Used by the system for temporary data management. Reset to Default There is a “Reset” button on the back of DISKMASTER which will help return its IP, System ID, System Password and DHCP to their factory default values.
APPENDIX C: USB Copy DISKMASTER is equipped with 2 USB hosts which supports “USB Mass Storage Device”. One is located on front panel and the other on the back panel. You can share all the data and contents on the device to all users through the File Server. There are two LEDs on the front panel to indicate if the USB device is ready or not. When USB devices are plugged in and mounted on DISKMASTER system successfully, you can check the USB device information from the “Hardware Info”.
The picture above shows the USB devices recognized by DISKMASTER system and their mounting structure. Root Directory Home Directory Sysadmin Home Home Samba_File Account Directory User1 User2 UserX public usbshare Struttura directory Public_html Public_html Public_html Cgi-bin Cgi-bin Cgi-bin usbshare_sdc_1 usbshare_sdc_x usbshare_sdd_1 usbshare_sdd_x Folder1 User1 User2 User…. FolderX ftp_file upload Home All USB devices will be mounted under the directory “usbshare”.
particulars of the device) To make these shared folders via File Server should drag the folder Samba_File.
APPENDIX D: WEB SERVER The device also thanks to integrated support for Apache / PHP / MySQL, can function as a real web server hosting many sites of medium complexity. Click on Web Server, will the image below. The menu in question is composed of four sub-menu: Status: allows you to enable or disable the Web Server module status. This service is not activated by default (after installation). Virtual Host: allows you to set the Virtual Host. PHP.ini Settings: can set the settings.
Level 1: E 'can only upload a web site, directly into the WWW. Here there are 2 folders html (for HTML) and cgi-bin (for CGI). Level 2: Are different, one for each user account created. Therefore each user directory will be created two nested directory: public_html and a subdirectory cgi-bin.
DiskMaster supports 2 types of CGI, PERL and SHELL (only basic libraries). To access the website hosted just type: http:// IP address DiskMaster http:// IP address DiskMaster/~UserX Does not support https protocol.
Virtual Host Settings Host virtual address allows you to use 2 or more domain names, each with their own independent pages. Click NEW ( ). You will see the screen below. WebSite Administrator: can be selected via the combo box, the administrator of each virtual site. Should be chosen among users previously created in DiskMaster. Virtual Host Name: enter the domain name (must Register yourself at your ISP) Name of Directory: It 'can create a new folder or use an existing.
After completing the Virtual Host settings, please click “enable” to activate the settings. PHP INi Settings PHP is used mainly for dynamic HTML (message boards, forums and chat rooms). The settings are customizable to taste in order to get the best result. If you change the settings of the php.ini, please click the "Save" to activate the changed values. There is a box next to "Restore default php.ini”. Ticking this box and clicking the "Save" will return the settings to default php.
Access stores information such as date, time, IP address, Username. Error: stores all abnormal activity. A single file contains information of a week. The file 1-4 respectively indicate (the current week, 2 weeks ago ...) Delete: remove the log file selected. Download: allows you to download the selected file and save it elsewhere LOG.
APPENDIX E: MySQL Database The device also built MySQL with support, can work as a real SQL database. Click on MySQL Database, you'll see the image below. The menu in question consists of three sub menu: Status: allows you to activate or deactivate the module status MySQL Database: This service is not activated by default (after installation). My.cnf Settings: can set the settings. Logs: stores the web server logs. Status MySQL Database Service is disabled by default.
MySQL Database requires that the Web Server service is installed and active. If it were not so will be appropriately marked. My.cnf Settings MySQL supports character set: UTF-8 Unicode (utf8). After entering the parameters click Save to make permanent and use the new configuration settings. See http://www.mysql.
Logs Records the log files of the MySQL status (either as Normal, Error, or Terminated) and is available for the administrator's reference. A single file contains information of a week. he file 1-4 respectively indicate (the current week, 2 weeks ago ...). Delete: remove the log file selected. Download: allows you to download the current log file and save it elsewhere.
APPENDIX F: PostgreSQL Database Postgre SQL is a great help (object oriented) to allow the database management SQLI. Click on the PostgreSQL database, you'll see the image below. The menu in question consists of three sub menu: Status: allows you to toggle the state of the PostgreSQL database module. This service is not activated by default (after installation). Logs: stores the web server logs. Status The PostgreSQL Database Service is disabled by default.
PostgreSQL Database requires detailed knowledge for its use. Logs Records the log files of the PostgreSQL status (either as Normal, Error, or Terminated) and is available for the administrator's reference . A single file contains information of a week. The file 1-4 respectively indicate (the current week, 2 weeks ago ...) Delete: remove the log file selected. Download: allows you to download the current log file and save it elsewhere.
APPENDIX G: DDNS This section explains how to configure Dynamic DNS DiskMaster section. Through the use of this feature, you can register a domain although associated with a dynamic IP. There are a multitude of DDNS server that offer this service for free. Will be sufficient to enable register for free and immediate service that will reach (remote) always Router responsible for connectivity. This way you can easily configurations remotely, access the Web site or FTP server.
Status DDNS Service is disabled by default. To enable service check DDNS Setting Start. When the service is active, it will show the screen below. It’s possible to stop or restart the service by checking the appropriate box.
Settings Click NEW ( ). The following image will appear where you can configure parameters for access and update the DDNS server. DDNS Module: Select from the combo-box the appropriate form (only display the installed modules). Domain Name: Enter the domain name assigned by your Dynamic DNS. Username: Enter the username of 'Dynamic DNS account. Password: Enter the password of 'Dynamic DNS account.. Ethernet Card: select the interface (usually eth0, in the case of PPPoE select ppp0).
If registration is successful and the service activated will show the IP address assigned to the registered domain (normally the responsibility of the router's WAN connectivity).
APPENDIX H: iTunes Server Enabling this service allows you to view files in the folders listed directly from iTunes. Click on the iTunes Server, the image will appear below. The menu in question consists of three sub-menu: Status: allows you to activate or deactivate the module status iTunes Server. This service is not activated by default (after installation) Settings: can set the settings. Playlist Setting: to set the settings of your playlists.
Settings Host Name: Identifies the iTunes Server on the network. Please give the iTunes Server a distinctive name on DISKMASTER so it can be easily identified. Rescan Interval: According to your settings, DISKMASTER will rescan and add new files into the iTunes list.. Filename Codepage: Select Unicode. Password: Set up your password. If You Want to Set the sharing limitations you can set to password here. Anyone Attempting to Access Your iTunes will then be required to type in a password.
When the iTunes service is active into DiskMaster is possible to save MP3 files in the folder specified in the Shared Folders and playback directly from DiskMaster that appears in iTunes under Shared Devices. Playlist Settings Edit to change the display style in iTunes, then click on save button.
Adjustment is recommended for advanced users only.
APPENDIX I: UPnP Media Server Click on UPnP Media Server, the image will appear below. The menu consists of two sub-menu: Status: allows to activate or deactivate the module status UPnP Media Server. This service is not activated by default (after installation) Settings: Allows you to set the settings. Status UPnP Media Server Service is disabled by default. To enable service check UPnP Media Server Start. When the service is active, you will see the screen below.
Settings Host Name: Choose your own name for the UPnP Media Server which must be distinctive to other UPnP servers in the network. Rescan Interval: According to your settings, it will rescan and add new file to the UPnP sharing list. Filename Codepage: Select Unicode. Share Folders: Place your media files in this folder. Before using the UPnP Media Server application, go to the File Server and create a shared first. Compatibility: Select the compatibility such as PS3 or Xbox360.
APPENDIX L: MultiProtocol DownLoad Click on Server-> Multiprotocol DownLoad, the image will appear below. The menu in question consists of three sub-menu: Status: allows to activate or deactivate the module status Multiprotocol Download. This service is not activated by default (after installation). Settings: Allows you to set the settings. Task List: Task list. Status The Multiprotocol DownLoad Service is disabled by default. To enable service check Multiprotocol DownLoad Start.
Settings The Maximum number of peers per torrent: Limits the amount of connections that can be made per torrent. Keep each torrent task sharing for: Set the file sharing duration to last after the file had finished downloading. Set Max overall download speed: Limits the downloading speed. (Includes all the protocol for downloading). Set Max overall upload speed: Limits the uploading speed.
Task List Click NEW ( ). Default folder: selected to place the file in the folder selected in Download folder name. Create a new folder: check to create a new subfolder (insert name) Protocol: select the checking protocol that will be used among those proposed. URL: Enter the URL to download Torrent o MetaLink File: Click Browse and select the file you downloaded torrent and then click on Upload. Delete a task: to cancel an active task.
APPENDIX M: Technical Features Protocols IP, NBNS(“NetBios” Name Server), Microsoft Networks (CIFS/SMB), DHCP Server/Client, SNTP Client, NTP LAN port 1 x RJ45 10/100/1000 Base-T port USB A Port 2*USB V2.
System Requirements for SmartSync Pro Package Contents Windows 2000, XP, Vista, 7, Server 2003, Server 2008, and Server 2008 R2. Both x86 and x64 versions.
APPENDIX N: Compatibility List Brand Western Western Western Western Western Seagate Seagate Seagate Hitachi Digital Digital Digital Digital Digital Model WD5000AAKS WD10EADS WD10EARS WD20EADS WD20EARS ST3200820AS HDS722020ALA330 MB 500 1000 1000 2000 2000 500 1000 2000 2000 Hard drive not included. An internal SATA I/II Hard Disk is required to share or store data files. This product may not work with older generation SATA/ I/II drives.
Atlantis SpA Via S. Antonio, 8/10 20020 Lainate (MI) info@atlantis-land.