Instruction manual
38
P-2000 7.1 Channel Preamp/Processor/Tuner
Instruction Manual
39
4.
Point the remote control toward the device that was turned on in
Step 1 and press in the rst three-digit setup code number for that
device using the number buttons (0-9) on the remote control.
The LED and selected Source button will blink and then stay lit after
you enter a setup code.
Your device will turn off when the correct setup code number has
been selected. If the device does not turn off, press in the next setup
code number from the listing. The remote will remain in this pro-
gramming mode as long as you continue to enter codes within 10
seconds of each other.
Continue entering setup code numbers until your device turns off,
then proceed to Step 5.
Note: If you have tried all of the three digit setup code numbers
listed for your device and it still did not turn off, please proceed to the
Auto Search Method below to program your remote control.
5.
Once your device turns off, press the Device Button selected
in Step 3 once again to store the setup code number.
The LED and Source button will blink twice and then go out.
6.
Test the remote control for your device. Try the POWER, CHANNEL
UP and DOWN, VOLUME UP and DOWN buttons, etc.
If any of the buttons do not perform as they should, please repeat
the setup from Step 1 using the next setup code number for your
device.
Note: Some audio/video devices have separate buttons for POWER
ON and POWER OFF. To operate these devices from the remote, press
the corresponding Source button to turn the equipment ON and press
the POWER button to turn the equipment OFF.
7. Please repeat the above steps to program the remote control
for each of your other devices.
If none of the setup code numbers worked for your device during the stan-
dard setup procedure, or if the manufacturer or brand for your device is not
listed in the Setup Code Tables, use the steps below.
To program using Auto Search
1.
Turn on the device you would like the remote control to
operate, either manually or with its original remote control.
3.
Press the corresponding Source button and the MUTE button
on the remote control simultaneously.
The red LED and the selected Source button will illuminate.
Note: The selected button and LED will remain for approximately
10 seconds to indicate that the remote control is ready to be pro-
grammed. The following steps must be entered while they are lit. If
the lights go out, simply start again by pressing the Source and MUTE
buttons to re-enter the setup mode.
3.
Point the remote control toward the device and, while watching the
device, press the CHANNEL UP button on the remote control.
Each press of the CHANNEL UP button sends the signal for one setup
code number. The LED and Source buttons will blink each time you
press the CHANNEL UP button. Keeping the CHANNEL UP button
pressed quickly scans through the setup code numbers.
Release the CHANNEL UP button as soon as the device turns off.
Conrm that you have the correct code by pressing the MUTE but-
ton on the remote. You should be able to turn your device on and off
with this button.
If you pass the correct setup code number, you can return to it by
pressing the CHANNEL DOWN button, one number at a time, until
your device turns back on.
Note: During the programming process the signal for POWER ON
and POWER OFF is located on the MUTE button. For devices that use
separate POWER ON and POWER OFF buttons, pressing the MUTE
button on the remote control during programming will only turn the
device OFF.
4.
Once the correct code is conrmed, press the selected Source
button again to store the setup code number.
The LED and Source button will blink twice and then go out, conrm-
ing the programming.
5.
Test the remote control for your device. Try the POWER, CHANNEL
UP and DOWN, VOLUME UP and DOWN buttons, etc.
If any of the buttons do not perform as they should, please repeat the
setup from Step 1 using the next setup code number for your device.
Note: Some audio/video devices have separate buttons for POWER
ON and POWER OFF. To operate these devices on the remote, press
the corresponding DEVICE Button to turn the equipment ON and press
the POWER button to turn the equipment OFF.
6.
Please repeat the above steps to program the remote control
for each of your other devices.
To display the stored three digit setup code number for a device:
1.
Press the corresponding Source button and the MUTE button
on the remote control simultaneously.
The red LED and the selected Source button will illuminate.
2.
Press the T/V button.
The LED and Source button will quickly ash the three digit setup code
number that was stored for your device, pausing between numerals.
The number zero (0) is indicated by ten ashes.
3.
Please write your setup code numbers in the chart below, for
future reference.
Set-Up Code Numbers:
CD TV
DVD VCR
AUX CBL
SAT
Operation
After you have programmed the remote control for your equipment,
use the following procedures to operate the components of your home
entertainment system:
Remote Control Setup and Operation