Instruction manual

22
P-2000 7.1 Channel Preamp/Processor/Tuner
Instruction Manual
23
System Setup
At this point you should have made all the necessary physical connections
between the P-2000 and your source equipment, ampliers and speakers.
All that remains is to properly congure the system to reect your specic
equipment and room characteristics.
To turn the P-2000 on:
1. Plug the cord into an AC wall outlet or UL approved power
strip or surge protection device.
Make certain that the AC power cord supplied with the P-2000 is rmly
inserted into the socket on the unit’s rear panel.
2. Press the rear panel POWER switch to the On position to set
the P-2000 to Standby mode.
The Standby Indicator on the Front Panel will light up.
3. Press the front panel Standby Power button to turn on the
P-2000 or press the AUD button on the remote control.
The FRONT PANEL DISPLAY will light up and the standby indicator
will turn off.
Navigating the Setup Menus
Setup of the P-2000 can be performed from the front panel of the unit, or
by using the remote control. Information is shown on the Front Panel Dis-
play and the ON SCREEN DISPLAY (OSD). All selections are made using a
combination of the following buttons:
Front Panel The MENU, Navigation ( <, >, and ) and SELECT
buttons below the Front Panel Display.
Remote Control The MENU, Navigation ( <, >, and ) and
SEL/PLAY buttons in the center of the remote.
These buttons will be referred to interchangeably, unless otherwise specied,
when referring to the Setup Menus.
The following example demonstrates how to navigate the P-2000 menu
system in general using the Speaker Conguration menu as an illustration.
For detailed information on a specic part of the setup process, consult the
pages relating to that topic.
To use the P-2000 menu system:
1. Press the MENU button to display the Main Menu.
The Main Menu appears on the Front Panel Display and the OSD:
MAIN MENU
INPUT CONFIG
MAIN MENU
> INPUT CONFIG
SPEAKER CONFIG
CHANNEL CALIB
CHANNEL CONFIG
SYSTEM CONFIG
MULTI-ZONE
PLII MUSIC PARAMETER
EXIT
2. Press or to select a Setup menu.
Your selection is indicated by the second line on the Front Panel
Display and by the position of the > cursor on the OSD.
3. Press SELECT to enter that menu.
Your selection appears on the Front Panel Display and the OSD:
SPEAKER CONFIG
FRONT :SMALL
SPEAKER CONFIG
> FRONT :SMALL
CENTER :SMALL
SURR :SMALL
SURR REAR :LB/RB
SUBWOOFER :ON
FRONT XOVER:100Hz
CENTER XOVER:100Hz
SURR XOVER:100Hz
RETURN TO MAIN MENU
4. Press or to select an item to adjust.
Your selection appears on the Front Panel Display and the OSD:
SPEAKER CONFIG
CENTER :SMALL
SPEAKER CONFIG
FRONT :SMALL
> CENTER :SMALL
SURR :SMALL
SURR REAR :LB/RB
SUBWOOFER :ON
FRONT XOVER:100Hz
CENTER XOVER:100Hz
SURR XOVER:100Hz
RETURN TO MAIN MENU
4. Press < or > to adjust a setting.
Your selection appears on the Front Panel Display and the OSD:
SPEAKER CONFIG
CENTER :LARGE
SPEAKER CONFIG
FRONT :SMALL
> CENTER :LARGE
SURR :SMALL
SURR REAR :LB/RB
SUBWOOFER :ON
FRONT XOVER:100Hz
CENTER XOVER:100Hz
SURR XOVER:100Hz
RETURN TO MAIN MENU
Once you have made your selections, you can use the and to return to the
Main Menu and/or exit the menu system. Alternatively, pressing the MENU
button once will return you to the Main Menu. Pressing the MENU button
a second time will exit the menu system. Note that the menus will remain
visible on the Front Panel and OSD until you exit the menu system.
IMPORTANT NOTE: When viewing static images such as on screen
menus or video game images using a CRT-based projector, plasma
display or direct-view CRT monitor or television, there is a risk of per-
manently “burning in” the image. Do not leave these images on for
an extended period of time. This type of damage is not covered by
the Atlantic Technology P-2000 warranty or any manufacturer’s video
device warranty.
System Setup