Specifications

NEW!
TRANSDUCERS
1468
NEW!
TRANSDUCERS
23
WHEN YOU NEED IT RIGHT, RIGHT NOW, CALL KELE.
kele.com888-397-5353 USA
March 2014
SINGLE* UMX RELAYS
UMX-8
UMX-4
8 7 6 5 4 3 2 1
3.5 0.75 1.50 2.25 0.5 0 0 0 0 0 0 0 0
4.0 1.00 2.00 3.00 1.0 X X X X X X X 1
5.0 1.25 2.50 3.75 1.5 X X X X X X X 0
6.0 1.50 3.00 4.50 2.0 X X X X X X 1 X
7.0 1.75 3.50 5.25 2.5 X X X X X X 0 X
8.0 2.00 4.00 6.00 3.0 X X X X X 1 X X
9.0 2.25 4.50 6.75 3.5 X X X X X 0 X X
10.0 2.50 5.00 7.50 4.0 X X X X 1 X X X
11.0 2.75 5.50 8.25 4.5 X X X X 0 X X X
12.0 3.00 6.00 9.00 5.0 X X X 1 X X X X
13.0 3.25 6.50 9.75 5.5 X X X 0 X X X X
14.0 3.50 7.00 10.50 6.0 X X 1 X X X X X
15.0 3.75 7.50 11.25 6.5 X X 0 X X X X X
16.0 4.00 8.00 12.00 7.0 X 1 X X X X X X
17.0 4.25 8.50 12.75 7.5 X 0 X X X X X X
18.0 4.50 9.00 13.50 8.0 1 X X X X X X X
19.0 4.75 9.50 14.25 8.5 0 X X X X X X X
20.0 5.00 10.00 15.00 9.0 1 1 1 1 1 1 1 1
*Dual UMX control available in PWM mode only. PWM time base doubles in “Dual UMX” mode.
4.0 1.00 2.00 3.00 -- 0 0 0 0 0 0 0 0
6.0 1.50 3.00 4.50 1.0 0 0 0 0 0 0 0 1
8.0 2.00 4.00 6.00 2.0 0 0 0 0 0 0 1 0
10.0 2.50 5.00 7.50 3.0 0 0 0 0 0 1 0 0
12.0 3.00 6.00 9.00 4.0 0 0 0 0 1 0 0 0
14.0 3.50 7.00 10.50 5.0 0 0 0 1 0 0 0 0
16.0 4.00 8.00 12.00 6.0 0 0 1 0 0 0 0 0
18.0 4.50 9.00 13.50
7.0 0 1 0 0 0 0 0 0
20.0 5.00 10.00 15.00 8.0 1 0 0 0 0 0 0 0
*Dual UMX control available in both current/voltage and PWM modes. PWM time base doubles in “Dual UMX” mode.
4.0 1.00 2.00 3.00 0.5 0 0 0 0 0 0 0 0
6.0 1.50 3.00 4.50 1.0 0 0 0 0 0 0 0 1
8.0 2.00 4.00 6.00 2.0 0 0 0 0 0 0 1 1
10.0 2.50 5.00 7.50 3.0 0 0 0 0 0 1 1 1
12.0 3.00 6.00 9.00 4.0 0 0 0 0 1 1 1 1
14.0 3.50 7.00 10.50 5.0 0 0 0 1 1 1 1 1
16.0 4.00 8.00 12.00 6.0 0 0 1 1 1 1 1 1
18.0 4.50 9.00 13.50 7.0 0 1 1 1 1 1 1 1
20.0 5.00 10.00 15.00 8.0 1 1 1 1 1 1 1 1
*Dual UMX control available in both current/voltage and PWM modes. PWM time base doubles in “Dual UMX” mode.
4.0 1.00 2.00 3.00 1.0 0 0 0 0 0 0 0 0
6.0 1.50 3.00 4.50 2.0 0 0 0 0 0 0 0 1
8.0 2.00 4.00 6.00 3.0 0 0 0 0 0 0 1 1
10.0 2.50 5.00 7.50 4.0 0 0 0 0 0 1 1 1
12.0 3.00 6.00 9.00 5.0 0 0 0 0 1 1 1 1
14.0 3.50 7.00 10.50 6.0 0 0 0 1 0 0 0 1
16.0 4.00 8.00 12.00 7.0 0 0 1 1 0 0 0 1
18.0 4.50 9.00 13.50 8.0 0 1 1 1 0 0 0 1
20.0 5.00 10.00 15.00 9.0 1 0 0 0 0 0 0 1
*Dual UMX control available in both current/voltage and PWM modes. PWM time base doubles in “Dual UMX” mode.
TABLE 4.
OUTPUT
EXPANDER
(each relay
independently
controllable)
For current/voltage
signal, DIP switches
5, 6, 7, and 8 are
OFF, OFF, ON, OFF.
For PWM signal, use
OFF, OFF, OFF, OFF.
TABLE 5.
4 or 8 INPUT
EXPANDER
For current/voltage
signal, DIP switches
5, 6, 7, and 8 are
OFF, ON, OFF, ON .
For PWM signal, use
OFF, OFF, ON, ON.
TABLE 6.
4 or 8 STAGE
SEQUENCER
For current/voltage
signal, DIP switches
5, 6, 7, and 8 are
OFF, ON, OFF, OFF.
For PWM signal, use
OFF, OFF, ON, OFF.
Note: for adjustable
thresholds, use UCS
Series
TABLE 7.
RTU
CONTROLLER
3 HEAT, 3 COOL,
FAN, ECONOMIZER
For current/voltage
signal, DIP switches
5, 6, 7, and 8 are
OFF, ON, ON, OFF
For PWM signal, use
OFF, ON, OFF, OFF.
PWM (SEC)
mA 5V 10V 15V 200 mSec Minimum
Delay Between
Pulses
Note: Each input command may vary to approximately
50% of the change to the next highest or lowest
command and still be considered valid.
Relay status
0 = Command OFF
1 = Command ON
X = No change of state
DISCRETE CURRENT AND VOLTAGE COMMANDS
CONTROL SEQUENCES (DIP SWITCHES 5, 6, 7, AND 8)
MULTI-FUNCTION INPUT / OUTPUT EXPANDER
UMX-4, UMX-8