Operation Manual

17
D
D
e
e
s
s
c
c
r
r
i
i
p
p
t
t
i
i
o
o
n
n
o
o
f
f
d
d
e
e
v
v
i
i
c
c
e
e
Pos. Name Order
number
1
Shrub and grass shear
2
Battery warning lamp
3
Trip switch
4
ON/OFF switch
5
Switch
6
Handle
7
Charging female connector
8
LED - charging indicator
9
Receiver (wheel set)
10
Cover 364175
11
Grass cutting tool 364176
12
Shrub cutting tool 364177
13
Cutting tool guard -grass cutting tool 364181
14
Wheel set 364173
15
Clamping screw 364174
16
Telescopic handle holder
17
Charger cable male connector
18
Charger 364182
19
Telescopic handle * 364172
20
Handle
21
Unlocking knob
22
Adjusting knob
23
Cutting tool guard – shrub cutting tool 364180
24
Safety label - 1 364179
25
Safety label - 2 364186
(* Partly optional accessories)
B
B
e
e
f
f
o
o
r
r
e
e
t
t
h
h
e
e
f
f
i
i
r
r
s
s
t
t
c
c
o
o
m
m
m
m
i
i
s
s
s
s
i
i
o
o
n
n
i
i
n
n
g
g
C
C
h
h
a
a
r
r
g
g
i
i
n
n
g
g
t
t
h
h
e
e
r
r
e
e
c
c
h
h
a
a
r
r
g
g
e
e
a
a
b
b
l
l
e
e
b
b
a
a
t
t
t
t
e
e
r
r
y
y
L Always use the supplied charger to charge the lithium
ion battery integrated in the machine.
• Only charge the battery at temperatures between 10°C and
40°C. Otherwise, the battery may be damaged or its service
life may be reduced.
L Mains connection: Compare the voltage given on the
machine model plate e.g. 230 V with the mains voltage
and
connect the hedge trimmer to the relevant and properly earthed
plug.
Fully charge the lithium ion batteries before first use or
after a longer storage period of the machine.
 Plug the charger cable male connector (17) into the
charging female connector (7) on the machine and connect
the charger to an electrical socket.
 The charging indicator LED (8) will light up red. ΠCharging
is in progress.
L The machine will warm up during the charging proc-
ess.
This is normal.
Do not use the machine during the charging process.
 The charging process is completed (after approx. 4 hours)
when the charging indicator LED lights green.
 After completed charging, disconnect the charging cable
connector (17) at first and then the charger from the mains.
T
T
e
e
l
l
e
e
s
s
c
c
o
o
p
p
i
i
c
c
h
h
a
a
n
n
d
d
l
l
e
e
*
*
(*Partly optional accessories)
A
A
s
s
s
s
e
e
m
m
b
b
l
l
i
i
n
n
g
g
t
t
h
h
e
e
t
t
e
e
l
l
e
e
s
s
c
c
o
o
p
p
i
i
c
c
h
h
a
a
n
n
d
d
l
l
e
e
Only use the telescopic handle together with the grass
cutting tool to cut edges on the ground.
 Slide the wheel set (14) on the receiver (9) and fix it
using the clamping screw (15).
 Insert the telescopic handle (19) into the telescopic
holder (16) until it engages with a click.
A
A
d
d
j
j
u
u
s
s
t
t
i
i
n
n
g
g
t
t
h
h
e
e
o
o
p
p
e
e
r
r
a
a
t
t
i
i
n
n
g
g
h
h
e
e
i
i
g
g
h
h
t
t
 Press the adjusting knob (22).
 You can release the adjusting knob while pulling or pushing
the telescopic handle.
 The adjusting knob engages in the next position.
R
R
e
e
m
m
o
o
v
v
i
i
n
n
g
g
t
t
h
h
e
e
t
t
e
e
l
l
e
e
s
s
c
c
o
o
p
p
i
i
c
c
h
h
a
a
n
n
d
d
l
l
e
e
 Press on the unlocking knob (21) and pull the telescopic
handle out of its holder (16).
C
C
o
o
m
m
m
m
i
i
s
s
s
s
i
i
o
o
n
n
i
i
n
n
g
g
S
S
w
w
i
i
t
t
c
c
h
h
i
i
n
n
g
g
O
O
n
n
/
/
O
O
f
f
f
f
S
S
w
w
i
i
t
t
c
c
h
h
o
o
n
n
 Remove the cutting tool guard (13 / 23).
 Push the trip switch (3) and then press the ON/OFF switch
(4).
 Release the trip switch.

If the machine is used together with the telescopic handle,
it can only be turned on/off on the handle (20).
L
When the battery is run down the battery warning
lamp (2) comes up red and the machine stops auto-
matically. Do not continue to operate the ON/OFF
switch as the battery may be damaged.
Charge the lithium ion batteries (Â „Charging the bat-
tery“).
S
S
w
w
i
i
t
t
c
c
h
h
o
o
f
f
f
f
 Release On/Off switch.
The cutting tool stops delayed after the machine is turned
off. Therefore wait until the cutting tool is stationary before
you restart the product.