SH76 Bluetooth Headset User manual ® -1-
1. Notice Before Using Thank you for purchasing the Bluetooth® Headset SH76. Please read this User's Manual completely before you use the Headset. SH76 designed for listening the high quality music wirelessly that based on the latest Bluetooth® wireless technology, it is built‐in MP3, AAC and apt‐X low latency codec for high quality audio streaming.
. Package Contents List Please inspect this package and refer to the package contents list below to verify all items were included in this package: 1) SH76 Bluetooth® headset(1) 2) USB Charging Cable(1) 3) User's Manual(1) 4. SH76 Bluetooth® Headset Overview ① Indicator LED ② Answer ③ Charging Port ④ Next Track / Volume + ⑤ Previous Track / Volume – ⑥ Microphone 5. Battery information The device is equipped with an integrated lithium‐polymer battery. The battery cannot be replaced.
charged and discharged several hundred times, but it loses its capacity over time. Disconnect the SH76 from the power supply as soon as the battery is fully charged, overcharging would reduce the service life of the battery. A charged battery will lose its capacity if it is not used on a regular basis. Important: Ensure that the battery is fully charged if you do not use the device for a long period of time. To avoid a complete discharge of the battery, the SH76 should be charged at least every 6 months.
music playing time, and up to 240 hours of standby time. However, the talk and standby times may vary when used with different mobile phones or other compatible Bluetooth® devices, usage settings, usage styles, and environments. When the battery power is low, the headset will remind you by voice prompt "Battery low" every 20 seconds, and the red indicator light starts to flash.
[General procedure ] 1) 2) 3) 4) 5) Keep the SH76 within 1 meter range of a Bluetooth®‐ready Mobile phone. Press and hold the Play/Pause button for about 4 s, the indicator light will flashes red and blue intermittently, the device is now in pairing mode. Find the Bluetooth® setting of your Mobile phone and start the search for Bluetooth® devices. (For further details, please read the operating instructions of your Mobile phone). From the list of devices found, select the "SH76".
Turn on your headset Slide the power switch to On to turn on your headset. If your headset has completed the pairing process successfully, when the headset is turned on, it will connect to the phone you last connected automatically. Please ensure your phone's Bluetooth® function is active. Turn off the headset Slide the power switch to Off to turn off the headset. Note: To conserve power, if the headset is not connected to a device for approximately 10 minutes, the headset will turn off automatically. 9.
10. Using for phone call Last number re‐dialing At standby status, double press the ANSWER, the last number you dialed will be re‐dialed. Note: the last number re‐dialing is available only for the first device if two Mobile phones are connected. The connection sequence can be determined by reconnect manually. Answering a call Press ANSWER shortly to answer the incoming call. Reject an incoming call Press and hold ANSWER for 2 seconds to reject the incoming call.
Volume adjusting Push toggle switch to increase or decrease volume. Mute While a call is in progress, Push toggle switch for 2s to mute the headset, a remindful tone would be heard every 10 seconds. Repeat the operation to un‐mute. 11. Safety and general information 1) 2) 3) 4) 5) 6) 7) 8) 9) Please read this User's Manual carefully and follow all instructions. To avoid any damage or malfunction of the device do not drop the device from high places.
mistreated. 10) 12. FCC & IC Statement Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. Note: The manufacturer is not responsible for ANY interference, for example RADIO or TV interference, caused by unauthorized modifications to this equipment. Such modifications could void the user's authority to operate the equipment. 13.
Within the EU this product is intended to be used in Austria, Belgium, Denmark, Finland, France, Germany, Greece, Ireland, Italy, Luxembourg, The Netherlands, Portugal, Spain, Sweden, and United Kingdom and within EFTA in Iceland, Norway and Switzerland. 14. Warranty The condition of this warranty and supplier's responsibilities under this warranty are as follows: Warranty is non‐transferable and is limited to the original purchaser only.
