H6 Bluetooth Wireless Headset
Contents , What s in the box ............................................................................................................ 1 Pair to your Bluetooth phone ........................................................................................ 2 Charging the battery ..................................................................................................... 4 Battery information ........................................................................................................
1 , What s in the box The headset contains the following parts: 1.Ear Gel 2.Volume Up Button 3.Volume Down Button 4.Multi-function Button 5.Indicator Light 6.Microphone 7.Speaker 8.Charging Socket 9.Ear Hook 9 Package contents list: Item Name Quantity A. H6 Bluetooth Headset.....................1 B. Travel Charger....................................1 C. Charging Cable..................................1 D. User Manual.......................................
2 Pair to your Bluetooth phone Before you use your headset the first time, you must pair the unit with a Bluetooth device e.g. Bluetooth mobile phone. This operation guide based on the Bluetooth phone as the host's device. Please refer to the following step to set up the pairing: 1 2 Ensure the headset is off. 4 3 Press and hold the MFB for 4 seconds until you see the Blue and Red LED light flash alternately to enterthe pairing mode.
NOTE: l If the pairing is successful, the headset will connect to your phone automatically, you may need to confirm the enquiry. l While the headset is paired with the phone and connected, the indication light will flash 2 times every 5 seconds. If failed or didn't connect to the phone, the blue indicator light will flash 1 time every 3 seconds.
3 Charging the battery This headset has an internal, non-removable, rechargeable battery. Do not attempt to remove the battery from the device as you may damage the device. Please refer to the following step to charge the battery: 1. Connect the charger to the correct outlet. 2. When the charger is connected to headset, the red indicator light will turn on during charging. If charging does not start, disconnect the charger, plug it in again. Charging the battery fully may take up to 2 hours. 3.
4 Battery information Your device is powered by a chargeable battery. The full performance of a new battery's an achieved only after two or three complete charge and discharge cycle. The battery can be charged and discharged hundreds of times, but it will eventually wear out. Unplug the charger from the electrical plug and the device when not in use. Do not leave a fully charged battery connected to a charger, since overcharging may shorten its lifetime.
*Turn off the headset At any working state after the headset turns on, press and hold MFB for 4 seconds, you will hear a melody from high to low, and the Red indicator light will flash 3 times at the same time, the headset turns off. Note l For saving the power, while the headset didn't connect to any device over 1 hour, the headset will turn off automatically. 6 Wearing your headset The headset can be worn on either the Left or Right ear.
7 Making a call * By phone's keypad At the stand-by state, dial the number on your phone directly to make a call. * Use Voice-Dialing At the stand-by state, press the MFB shortly, you will hear a short tone from the headset, and the phone will prompt you say the voice tag like your friend's name. If the voice tag is identified by the phone, the related number will be dial-out later.
8 Ending a call When in the calling, press the MFB shortly will end the call, also you can end call on your mobile. 9 Reject an incoming call When you receive an incoming call, press and hold MFB for 2 seconds will reject the incoming call. 10 Answering a call When you receive an incoming call, press the MFB shortly can pick up the incoming call; also you can pick up the call on your mobile.
* While you are in the calling and another call was holding on, press MFB shortly can end current call and resume the holding on calling. * While you are in the calling and another call was holding on, press and hold MFB for 2 seconds can shift the current calling to the holding on calling. * While you are in the calling and another call was holding on, press Volume Up button shortly can add the holding on call to the current conversation to make a multiparty call.
15 Summary of button operation HEADSET STATUS Button ACTION Quick Press Multifunction Button Volume Up Incoming Call Answer incomingcall 2 Seconds Initiate voice dialing Initiate Voice dialing of phone 2 _ 4 Seconds Turn headset OFF Turn headset OFF Quick Press Increase volume Increase volume 2 Seconds Re-dial last number of phone 2 Double Press 4 Seconds Volume Down Standby (No Calls Active) _ Decrease volume 2 Seconds Re-dial last number _ Decrease volume _ _ _ 10 End a call _
HEADSET STATUS Button ACTION Multifunction Button Double press Quick Press Volume Up Answer incoming call, hold active call 4 Seconds Turn headset OFF Quick Press Increase volume 2 Seconds 4 Seconds 2 Seconds 4 Seconds 1 Call Active, 1 Call on Hold End active call , retrieve held call End all of the calls 2 Seconds Quick Press Volume Down 1 Call Active, 1 Incoming Call Answer incoming call, end active call _ Shift Calls Turn headset OFF Add held call to TWC Transfer active calling to/from
16 Safety and general information 1.Please read this guidebook carefully and follow the instructions. 2.To avoid any damage or malfunction of the device do not drop device from high places. 3.Keep device away form humidity, water and any other liquid. If the device is exposed to water, moisture and other liquid , do not operate it to avoid any electrical shock, explosion and damage to the device or yourself. 4.
17 FCC & IC Statement Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Note: The manufacturer is not responsible for ANY interference, for example RADIO or TV interference, caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment.
19 Warranty The condition of this warranty and our responsibilities under this warranty are as follows: Warranty is non-transferable and is limited to the original purchaser only. * You must be able to prove the date of original purchase of the unit with a dated receipt. * The warranty is not applicable if the product has been subject to physical abuse, improper installation, modification or repair by unauthorized third party.
Made in China
FCC Warning This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE 1: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
