Bluetooth® Headset BT1000 -1-
1. Notice Before Using Thank you for purchasing the Celltronix® Bluetooth® Headset BT1000. Please check the contents of this package to verify the items listed below have been included in your package. Please read this User's Manual completely before you use the Headset. The BT1000 has been developed using Bluetooth® wireless technology and is capable of connecting with Bluetooth® devices designed with Audio Gateway.
2. Package Contents List Please inspect this package and refer to the package contents list below to verify all items were included in this package: A. BT1000 Bluetooth® headset...........................................1 B. AC Travel Charger............................................................1 C. DC Car Charger................................................................1 D. USB Charging Cable........................................................1 E. User's Manual..............................
® Headset Overview 3.
4. Battery information The device is equipped with an integrated lithium-polymer battery. The battery cannot be replaced. Do not attempt to remove the battery from the device since it would damage the device. The full performance of a new battery is not achieved until after two or three complete charging-discharging cycles. The battery can be charged and discharged several hundred times, but it looses its capacity over time.
5. Charging the battery The BT1000 is operated with a rechargeable battery. Charge the battery completely before its first use. Read the section "Battery information" before starting the charging process. 1) Connect the charger to the correct outlet. 2) When the charger is connected to the headset, the red indicator light will turn on. Charging the battery fully may take up to 2 hours. 3) When the battery is fully charged, the red indicator light will turn blue.
mobile phones or other compatible Bluetooth® devices, usage settings, usage styles, and environments. When the battery power is low, the headset will remind you by "Beep" tone every 20 seconds, and the red indicator light starts to flash. - For using the BT1000 with iPhone or Blackberry, a additional battery meter feature will be activated, the remaining battery capacity will display on your phone. ® phone 6.
the unit with a Bluetooth® enabled mobile phone. Pairing is a one-time process and required only for the first connection with the cell phone The BT1000 can be paired with up to eight cell phones and be connected simultaneously with two cell phones. - Hold the BT1000 within range of a Bluetooth®-ready cell phone; - the distance should not exceed a meter. - The BT1000 must be turned off . - Press the On/Off button for approx.
- From the list of devices found, select the "BT1000". - If required, enter the PIN code "0000" and confirm the entry. If the pairing process was successful, you will hear a signal tone and the indicator lights blue for 3 seconds. (Note: The PIN code is preprogrammed and cannot be changed.) - After pairing, the BT1000 automatically connects with the cell phone. For some cell phones, you have to manually confirm the connection.
Establishing a connection with two cell phones There are several options of connecting the BT1000 with already paired cell phones. - Automatic connection When turning on the BT1000, a connection is automatically established with the two most recently connected cell phones. - Establishing a connection via the BT1000 To manually establish a connection between the BT1000 and the two most recently connected cell phones, press the On/Off button.
cell phone. After successful connection, you can establish another connection with a second cell phone. This allows you to determine the sequence of connections. If two cell phones are connected with the BT1000, the cell phone connected first is the first device and the other one the second device. Another connection can be established only after first disconnecting one of the two cell phones. The cell phone which is still connected afterwards becomes the first device in the sequence.
seconds until you hear a tone from low to high. The headset is now on. The Blue indicator light will be solid for 2 seconds. ® phone Connecting to a Bluetooth Bluetooth® If your headset has completed the pairing process successfully, when the headset is turned on, it will connect to the phone you last connected with automatically. Please ensure your phone's Bluetooth® function is active. Turning off the headset At any working state after the headset is powered on, press and hold On/Off for 5 seconds.
9. Wearing your headset According to your preference, you can wear the headset on your left or right ear. The adjustable head strap design allows for a comfortable wearing. 10. Using the BT1000 Making a call - Using phone's keypad In stand-by mode, dial the number on your phone's keypad to make a call.
In the stand-by mode, press the On/Off shortly, you will hear a short tone from the headset, and the phone will prompt you to say the voice tag which you have already attached to your contact. If the voice tag is identified by the phone, the related number will be dialed. Please insure that your mobile phone supports this voice dialing function, and voice tags have been set up on your mobile phone prior to attempting this. Refer to your mobile phone's user guide or contact your service provider.
Answering a call When you receive an incoming call, press the On/Off button shortly to answer the incoming call; you can also answer the call on your phones keypad. Reject an incoming call When you receive an incoming call, press and hold On/Off button for 3 seconds to reject the incoming call. Transferring a call While a call is in progress on your mobile phone, press and hold Volume (+) for 3 seconds. The call will be transferred from your mobile phone to your headset.
Call-waiting (Three-Way Calling) Before using the Call-Waiting function on your headset, please ensure that your phone supports this Hands-free profile and you have access to the service by wireless provider. - If there is another incoming call while a call is in progress on your mobile phone, press On/Off shortly. This will accept the waiting call and end current calling.
held call. - While you are engaged in one call with another call on hold, Double press Volume (-) button to add the held call to the current conversation for making a three-way call. - While you engaged in a three-way call, double press On/Off to end all calls. Volume control While on a call, you can adjust the volume by pressing the Volume(+) and Volume(-)button or you can adjust the volume on your mobile phone keypad.
cancelled. Music streaming The BT1000 supports A2DP profile that can streaming stereo music from the phone. The music will pause automatically while a call is dialed out/incoming, and resume while the conversation is ended. 11. Reset the BT1000 The BT1000 can be paired with up to eight cell phones. You can delete the paring list and reset the headset to the factory settings. – The BT1000 must be turned on and no connection may exist to a cell phone.
stand-by mode without connection. 12. Safety and general information 1) 2) 3) 4) 5) Please read this User's Manual carefully and follow all instructions. To avoid any damage or malfunction of the device do not drop the device from high places. Keep device away form humidity, water and any other liquid. If the device is exposed to water, moisture and other liquids do not operate it to avoid any electrical shock, explosion and damage to the device or yourself.
void the warranty. 6) Do not place heavy objects on the device. 7) Use only supplied and approved charger. 8) Replacement or service must be done by a qualified service center or manufacturer. 9) Unplug this device when unused for long periods of time or during lightening storms. 10) The battery used in this device may present a risk of fire or chemical burn if mistreated. 13. FCC & IC Statement Operation is subject to the following two conditions: (1) This device may not cause harmful interference.
14. EC Declaration of Conformity Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. Note: The manufacturer is not responsible for ANY interference, for example RADIO or TV interference, caused by unauthorized modifications to this equipment. Such modifications could void the user's authority to operate the equipment.
not harmonized within EU. Within the EU this product is intended to be used in Austria, Belgium, Denmark, Finland, France, Germany, Greece, Ireland, Italy, Luxembourg, The Netherlands, Portugal, Spain, Sweden, and United Kingdom and within EFTA in Iceland, Norway and Switzerland. 15. Warranty The condition of this warranty and supplier's responsibilities under this warranty are as follows: Warranty is non-transferable and is limited to the original purchaser only.
replacement of the product at its sole discretion. - Specifically exempt from any warranty are limited-life consumable components subject to normal wear and tear such as batteries, decorates and other accessories. - Supplier is not responsible, for failure resulting from accident, abuse, misuse, or any unauthorized repair, or modification. - Modification and repair of the unit should be done by an authorized and qualified service center or returned to the manufacturer.
Bluetooth® is a trademark owned by the Bluetooth® SIG, Inc.
