Installation manual

Series C Controller Configuration and Operation Manual
21-4  Athena Controls, Inc. 900M050U00
range
PID output, 7-7
setpoint, 5-14
rAS menu. See remote analog setpoint menu
rate, 1-8, 8-5, 8-6, 16-1, 16-3, 16-4
recipe events
configuring, 11-11, 11-13
dedicating alarm, 1-14, 9-3
LED use, 1-14
recipe holdback parameter, 11-5, 11-9
recipe option, 11-4
recipes
contact/digital input control, 14-2, 14-11
execution directed by external host, 2-3
holding, 1-5, 2-13
holding, 2-2
parameters, 11-1
resuming, 1-5, 2-13
setpoint, 1-11
starting, 2-2, 2-13
termination state, 2-13
recovery, 1-8, 3-5, 3-6, 10-1, 16-3
recycle number, 11-10
register ordering, 14-7
remote analog setpoint, 1-12, 14-2
remote analog setpoint menu, 4-7, 14-2, 14-4,
14-12
resume from power failure, 11-10
reverse output action, 7-4, 7-5
reversed sensor detected, 2-2, 19-1
r-S menu. See ramp/soak menu
RTD inputs, 1-16, 5-1, 5-6, 5-9, 6-3, 13-1, 18-1,
20-2
S
safety information, I
scaling
auxiliary output, 14-10
inputs, 1-16, 5-13
remote analog setpoint, 14-12
second setpoint, 1-12, 14-2, 14-11
security access levels
described, 1-7, 17-1
menus, 2-5
self-diagnostics failed, 2-3, 19-2
sensor failure, 12-2
sequence of configuration parameters, 1-16
serial communication. See communication
serial menu, 4-6
setpoint
alarm, 7-12, 9-6
at recipe termination, 11-6, 11-9
changing, 2-10, 14-2
displaying, 1-2, 1-17, 2-2
ramping to, 1-17, 2-13, 2-14, 11-5
retransmission, 14-10
specifying range, 5-10, 5-14
setpoint display blanking, 6-4, 6-6, 20-3
setpoint only (access level), 1-7, 17-1
setpoint plus mode (access level), 1-7, 17-1
setpoints, 1-11, 20-3
configuring, 1-12
single-setpoint ramp, 1-3, 1-17, 2-13, 11-5
soak events, 9-3, 11-13
dedicating alarm, 1-14
soak levels, 11-1, 11-12
soak times, 11-12
span adjustment, 5-1, 13-1, 18-1
standard outputs, 1-14, 7-1, 7-6
standby mode
accessing, 2-10
before configuration, 1-6
contact/digital input control, 14-2, 14-11
operational display, 2-2
selection display, 1-5
supervisor menu, 12-1
SUPr menu. See supervisor menu
T
technical support, 20-1
telephone number for tech support, 20-1
termination state, 11-6, 11-9
thermocouple inputs, 1-16, 5-1, 5-6, 5-9, 6-3,
13-1, 18-1, 20-2
transmission delay, 14-9
troubleshooting, 19-1, 20-1
tunE menu. See Autotune damping menu
tuning
automatically, 16-2
manual procedure, 16-4
parameters, 1-8, 8-1, 8-5, 16-1, 16-3, 16-4,
16-5
U
units of measure, 1-16, 6-4
up key, 1-3, 2-8
user (access level), 1-7, 17-1
user interface, 1-2, 2-1
V
voltage inputs, 5-1, 5-6, 5-12, 6-5, 13-1, 18-1
Z
zero offset, 5-1, 13-1, 18-1