Installation manual

Index
900M050U00  Athena Controls, Inc. 21-3
M
manual mode, 1-2, 2-2, 2-11
permission to change outputs, 1-7, 17-1
selection display, 1-5
manual reset, 1-8, 8-5, 8-6, 16-1, 16-4, 16-5
manual tuning procedure, 16-4
menu access key, 1-3, 2-8
menu system, 1-6
accessing, 2-16
display sequence, 2-4, 4-5
permission to access, 1-7, 2-5, 17-1
milliamp inputs, 5-1, 5-6, 5-12, 6-5, 13-1, 18-1
millivolt inputs, 5-1, 5-6, 5-12, 6-5, 13-1, 18-1
Modbus protocol
Autotuning with, 16-2
calibration with, 18-4
configuring communication parameters, 1-4,
14-3, 14-6, 20-2
manual tuning with, 16-4
option cards, 1-4, 14-1
programming controllers with, 1-2
reading error codes, 19-1, 19-2
recpe execution, 2-3
mode/enter key, 1-2, 2-8
modes of operation
displays, 2-2
permission to change, 1-7, 17-1
selecting, 1-5, 2-8
mounting controllers, 1-2
Multi-Comm application
Autotuning with, 16-2
calibration with, 18-4
error messages, 4-9, 15-1
executing recipes, 2-3
manual tuning with, 16-4
reading error codes, 19-1, 19-2
serial communication, 1-4, 14-8, 20-2
N
normal band alarms, 1-13, 7-10, 7-12, 9-4, 9-6
normal mode, 1-2, 1-11, 2-2, 2-11, 20-3
selection display, 1-5
O
on/off control
advantages and disadvantages, 1-9, 20-2
configuration, 7-4
output type, 7-3
on/off deadband
configuration, 8-3
example, 1-10
on/off hysteresis
configuration, 8-3, 8-4
example, 1-9
limited by input scaling, 5-13
open sensor detected, 2-2, 19-1
option cards, 14-1, 14-5, 14-8
option menu, 4-6, 14-1
OPtn menu. See option menu
OutP menu. See output menu
output failsafe values, 12-2
output menu, 4-5, 7-1
output range for PID, 7-7
outputs
functions, 1-2
state during standby mode, 2-4
state on power up, 1-17
use for alarms, 1-3, 7-9
overshoot, 1-8, 1-10, 3-5, 3-6, 10-1, 16-3
P
parameter display sequence, 4-5
parity, 14-7, 14-9
permission levels, 1-7, 17-1
phone number for tech support, 20-1
PID control
advantages and disadvantages, 1-8, 20-2
instructions for quick setup, 3-1
output action, 7-5
output type, 7-3
tuning, 10-1, 16-1
power failure resume, 11-10, 19-3
powering up controller, 1-17
process alarms, 1-13, 7-10, 7-12, 9-4, 9-6
process lag, 1-8
process value
display, 1-2, 20-3
displaying, 2-2
highest, 12-3
lowest, 12-3
retransmission, 14-10
processor board, 5-2, 17-4
proportional band, 1-8, 8-5, 8-6, 16-1, 16-3, 16-4,
16-5
Proportional-Integral-Derivative control. See PID
control
PV. See process value
R
RAM error, 19-2
RAM, writing setpoints, 1-11
ramp events, 9-3, 11-11
dedicating alarm, 1-14
ramp times, 11-1, 11-11
ramp/soak execution, 1-3
contact/digital input control, 14-2, 14-11
directed by external host, 2-3
holding, 1-5, 2-2, 2-13
resuming, 1-5, 2-13
starting, 2-2, 2-13
termination state, 2-13
ramp/soak menu, 1-7, 1-14, 4-6, 11-1, 17-1