cs102u.
cs102u.fm Page 2 Friday, June 6, 2008 3:42 PM FCC Information This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instruction manual, may cause interference to radio communications.
cs102u.fm Page 3 Friday, June 6, 2008 3:42 PM CS-102U User Manual Package Contents The CS-102U package contains the following items: 1 CS-102U USB KVM Switch 2 USB/VGA Cables 1 User Manual* Check to make sure that all the components are present and that nothing got damaged in shipping. If you encounter a problem, contact your dealer.
cs102u.fm Page 4 Friday, June 6, 2008 3:42 PM Overview The Master view CS-102U represents a revolutionary new direction in KVM Switches: a dual function 2 Port KVM Switch plus 2 Port USB Hub control unit. The CS-102U incorporates USB technology to handle the data connection between itself and the connected computers, and to provide two USB ports for peripheral devices that the connected computers can share.
cs102u.
cs102u.fm Page 6 Friday, June 6, 2008 3:42 PM System Requirements Console The console must consist of the following components: A VGA, SVGA, or Multisync monitor capable of the highest resolution that you will be using on any computer in the installation. A USB keyboard A USB mouse Computers The following equipment must be installed on each computer that is to be connected to the system: Windows 98 / Mac OS 8.6 or higher A USB Host Controller installed on the system.
cs102u.fm Page 7 Friday, June 6, 2008 3:42 PM Components Front View 1. Port Selection / Auto Scan Switch: This pushbutton has two functions: It toggles access back and forth between the computers. It activates / deactivates Auto Scan Mode. Holding this switch down for 2 seconds activates Auto Scan Mode; pressing and releasing the switch while Auto Scan Mode is active turns Auto Scan Mode Off. 2. Port LEDs: A LED lights to indicate that its corresponding port is the one that has the KVM focus.
cs102u.fm Page 8 Friday, June 6, 2008 3:42 PM Rear View 1. Console Video Connector: The monitor's video cable plugs in here. 2. CPU Video Ports: These ports link to the video ports on the computers you are installing. 3. USB Peripheral Ports: USB peripherals that you want to use on the installation plug in here. Devices can plug into any available port. 4. CPU USB Ports: These ports link to the USB ports on the computers you are installing. 5.
cs102u.fm Page 9 Friday, June 6, 2008 3:42 PM Installation 1. Make sure that the power to any device that you connect to the installation has been turned off. You must unplug the power cords of any computers that have the Keyboard Power On function. 2. To prevent damage to your equipment due to ground potential difference, make sure that all devices on the installation are properly grounded. Consult your dealer for technical details, if necessary.
cs102u.fm Page 10 Friday, June 6, 2008 3:42 PM Note: 1. For PC users (Mac users do not need to do this step), at bootup, enter the PC's CMOS Setup program (see the on screen instructions at bootup for how to enter the CMOS Setup program), and make the following changes: In STANDARD CMOS, set HALT ON ERROR to: ALL BUT KEYBOARD In PNP AND PCI SETUP, set PNP OS INSTALLED to: YES; set USB IRQ to: ENABLED. 2. The CS-102U's Power On default is to link to Port 1.
cs102u.fm Page 11 Friday, June 6, 2008 3:42 PM Operation Manual Port Selection With Manual Port Selection you simply press the Port Selection Button on the CS-102U's top panel to switch the KVM focus back and forth between computers. The Port LEDs light to indicate which port has the focus. Note: The drivers for most USB devices (CCD Cameras, Scanners, Printers, e.g.), are required to be shut down before you disconnect the device, or else the system may crash.
cs102u.fm Page 12 Friday, June 6, 2008 3:42 PM Auto Scan Mode The Auto Scan feature automatically switches between the two computers at regular 5 seconds intervals, so that you can monitor their activity without having to take the trouble of switching yourself. To invoke Auto Scan Mode, simply hold down the Port Selection push button switch for two seconds. The Port LEDs flash when their corresponding ports are accessed under Auto Scan Mode.
cs102u.fm Page 13 Friday, June 6, 2008 3:42 PM Troubleshooting Problem Keyboard not responding. Mouse Not Detected, or Does Not Respond Correctly Video Problems Cause Action Loose cables. Check all keyboard cable connections to make sure they are completely seated in their sockets. Keyboard needs to be reset. Unplug the keyboard from the Console Keyboard Port, then plug it/them back in. CS-102U needs to be reset. Turn off the computers and the CS-102U.
cs102u.fm Page 14 Friday, June 6, 2008 3:42 PM Specifications Function Specification Computer Connections 2 Port Selection Push Button Switch LEDs 2 - Selected Port Connectors USB Type A 4 - USB Peripherals USB Type B 2 - Link to Computers Video 1 x HDB-15 Female - Console 2 x HDB-15 Male - Link to Computers Power 1 x DC 5V Jack Power Consumption DC 5V 11 mA (max.) Scan Interval 5 sec USB Specification 1.1 Compliant Environment Operating Temp. 5–40o C Storage Temp.
cs102u.fm Page 15 Friday, June 6, 2008 3:42 PM Limited Warranty IN NO EVENT SHALL THE DIRECT VENDOR'S LIABILITY EXCEED THE PRICE PAID FOR THE PRODUCT FROM THE DIRECT, INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THE PRODUCT, DISK OR ITS DOCUMENTATION.
