4/8-Port HDMI over single Cat 5 Splitter VS1814T / VS1818T User Manual www.aten.
VS1814T / VS1818T User Manual FCC Information FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
VS1814T / VS1818T User Manual User Information Online Registration Be sure to register your product at our online support center: International http://eservice.aten.
VS1814T / VS1818T User Manual Package Contents The VS1814T / VS1818T 4/8-Port HDMI over single Cat 5 Splitter package consists of: 1 VS1814T / VS1818T 4/8-Port HDMI over single Cat 5 Splitter 1 Power Cord 1 Mounting Kit 1 User Instructions* Check to make sure that all the components are present and that nothing got damaged in shipping. If you encounter a problem, contact your dealer.
VS1814T / VS1818T User Manual Contents FCC Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii RoHS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii SJ/T 11364-2006. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii User Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii Online Registration . . . . .
VS1814T / VS1818T User Manual Appendix Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Rack Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Technical Support. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 International . . . . . . . . . . . . . . . . . . .
VS1814T / VS1818T User Manual About this Manual This User Manual is provided to help you get the most from your VS1814T / VS1818T system. It covers all aspects of installation, configuration and operation. An overview of the information found in the manual is provided below. Introduction, introduces you to the VS1814T / VS1818T system. Its purpose, features and benefits are presented, and its front and back panel components are described.
VS1814T / VS1818T User Manual Conventions This manual uses the following conventions: Monospaced Indicates text that you should key in. [] Indicates keys you should press. For example, [Enter] means to press the Enter key. If keys need to be chorded, they appear together in the same bracket with a plus sign between them: [Ctrl+Alt]. 1. Numbered lists represent procedures with sequential steps. ♦ Bullet lists provide information, but do not involve sequential steps.
Chapter 1 Introduction Overview The ATEN VS1814T / VS1818T 4/8-Port HDMI over single Cat 5 Splitter is a fast and efficient way of switching digital high definition video from one input source to 4/8 displays located up to 100m away. It implements HDBaseT extension technology to connect the VS1814T / VS1818T to receiver units over one single Cat 5e cable in order to transmit rich HDMI multimedia content in real time.
VS1814T / VS1818T User Manual Features One HDMI input to 4/8 HDMI outputs via a Cat 5e cable Offers local HDMI output Extends displays up to 100 m Anti-jamming – resists signal interference during high-quality video transmissions using HDBaseT technology Implements HDBaseT extension technology using only one Cat 5 cable to connect the transmitter and receiver HDMI (3D, Deep color, 4kx2k); HDCP Compatible Supports Dolby True HD and DTS HD Master Audio Consumer Electronics Control (CEC) suppo
Chapter 1.
VS1814T / VS1818T User Manual Components Front View 1 No. 2 3 4 5 6 Component Description 1 HDBaseT Out port LEDs (1~4 / 1~8) Lights to indicate there is a working connection to the HDMI receiving device(s) connected to the port(s). 2 HDMI Out LED Lights to indicate there is a working connection to the local display device. 3 HDMI In LED Lights to indicate that there is a working connection to the source device (i.e., computer).
Chapter 1. Introduction Rear View 1 No. 2 3 4 Component 6 5 7 8 9 Function 1 Power Socket This is a standard 3-pin AC power socket. The power cord from an AC source plugs in here. 2 Power Switch This is a standard rocker switch that powers the unit on and off. 3 Grounding Terminal The grounding wire attaches here. See Grounding, page 9, for further details. 4 EDID Mode Switch Press this button to cycle through the EDID settings stored in the unit (see EDID Mode Selection, page 12).
VS1814T / VS1818T User Manual This Page Intentionally Left Blank 6
Chapter 2 Hardware Setup 1. Important safety information regarding the placement of this device is provided on page 19. Please review it before proceeding. 2. Make sure that the power to all devices connected to the installation are turned off. 3. Make sure that all devices you will be installing are properly grounded. Rack Mounting For convenience and flexibility, the VS1814T / VS1818T can be mounted on system racks. To rack mount a unit do the following: 1.
VS1814T / VS1818T User Manual 2. Screw the bracket into any convenient location on the rack.
Chapter 2. Hardware Setup Grounding To prevent damage to your installation, it is important that all devices are properly grounded. 1. Use a grounding wire to ground the VS1814T / VS1818T by connecting one end of the wire to the grounding terminal, and the other end of the wire to a suitable grounded object. 2. Make sure that all devices in your VS1814T / VS1818T installation are properly grounded.
VS1814T / VS1818T User Manual Installation Refer to the installation diagram (the numbers in the diagram correspond to the numbers of the steps) and do the following: 1. Use an HDMI Type A Male-to-Male cable to connect your computer or HDMI source device to the VS1814T / VS1818T’s HDMI Input port. 2. Use up to 4 (VS1814T) / 8 (VS1818T) Cat 5e cables to connect up to four / eight HDMI Receiver units (i.e. VE812R) to the HDBaseT Out ports.
Chapter 3 Operation Overview The VS1814T / VS1818T offers easy and flexible EDID learning and mode selection through pushbuttons located in the unit’s front and rear panels. EDID Learn Pushbutton The VS1814T / VS1818T can automatically learn a display’s EDID by pressing the EDID Learn Pushbutton located on the front panel. Follow these steps: 1. Attach the video display/monitor that you want to use to the VS1814T / VS1818T HDMI Output port (See Installation, page 10). 2.
VS1814T / VS1818T User Manual EDID Mode Selection The VS1814T / VS1818T offers an easy and flexible EDID Mode selection method using the rear panel EDID Mode Switch. Extended Display Identification Data (EDID) is a data format that contains a display's basic information and is used to communicate with the video source/ system.
Chapter 4 RS-232 Commands Overview In order to use the RS-232 serial interface to attach a high-end controller (such as a PC) to the VS1814T / VS1818T, use a serial cable such as a modem cable. The end connecting to the VS1814T / VS1818T should have a 9-pin male connector. Connect this to the serial interface on the rear of the VS1814T / VS1818T. Refer to number 4 on the diagram on page 12. Note: To configure the controller serial port, see page 10.
VS1814T / VS1818T User Manual Switch Port The available formulas for Switch Port commands are as follows: Switch Command + Output Command + Port Number + Control [Enter] 1. For example, to turn on output port 02, type the following: sw o02 on 2.
Chapter 4. RS-232 Commands CEC Commands Consumer Electronics Control (CEC) allows interconnected HDMI devices to communicate and respond to one remote control.
VS1814T / VS1818T User Manual Read Commands View information from the device using the following command: Read Command + Control [Enter] The following tables show the possible values and formats for the Control command: Command Description read Reads and displays information from the VS1814T / VS1818T Control Description version Displays the firmware version of the VS1814T / VS1818T (blank) Displays the Port and CEC status (on/off) The following table shows the available command list: Command Co
Chapter 4. RS-232 Commands Baud Rate Setting Commands You can set up the VS1814T / VS1818T baud rate via RS-232.
VS1814T / VS1818T User Manual Reset Commands Reset the VS1814T / VS1818T to default factory settings using the following command: Reset Command [Enter] The following tables show the possible value for the Control command: Command Description reset Resets to factory default settings The following table shows the available command list: Command Enter reset [Enter] Description Resets the VS1814T / VS1818T Note: The Reset command reverts to the default baud rate, as well as switches on all output devi
Appendix Safety Instructions General Read all of these instructions. Save them for future reference. Follow all warnings and instructions marked on the device. This product is for indoor use only. Do not place the device on any unstable surface (cart, stand, table, etc.). If the device falls, serious damage will result. Do not use the device near water. Do not place the device near, or over, radiators or heat registers.
VS1814T / VS1818T User Manual Never push objects of any kind into or through cabinet slots. They may touch dangerous voltage points or short out parts resulting in a risk of fire or electrical shock. Do not attempt to service the device yourself. Refer all servicing to qualified service personnel. If the following conditions occur, unplug the device from the wall outlet and bring it to qualified service personnel for repair. Liquid has been spilled into the device.
Appendix Rack Mounting Before working on the rack, make sure that the stabilizers are secured to the rack, extended to the floor, and that the full weight of the rack rests on the floor. Install front and side stabilizers on a single rack or front stabilizers for joined multiple racks before working on the rack. Always load the rack from the bottom up, and load the heaviest item in the rack first. Make sure that the rack is level and stable before extending a device from the rack.
VS1814T / VS1818T User Manual Technical Support International For online technical support – including troubleshooting, documentation, and software updates: http://eservice.aten.com For telephone support, see Telephone Support, page iii: North America Email Support Online Technical Support support@aten-usa.com Troubleshooting Documentation Software Updates Telephone Support http://www.aten-usa.
Appendix Specifications Function Connectors HDMI In HDMI Out HDBaseT Out Power Jack RS-232 Switches EDID Mode VS1814T 1 x HDMI Type A Female (Black) 4 x RJ-45 Female LEDs 1 x 3-prong AC socket 1 x 8-position switch 1 x pushbutton 1 x semi-recessed button Power 1 x Rocker Power 1 (Green) HDMI In 1 (Green) HDMI Out 1 (Green) EDID Learn HDBaseT Out Video 1 (Green / Red) 4 (Green) 120V / 20W; 230V / 23W Operating Temp.
VS1814T / VS1818T User Manual Limited Warranty IN NO EVENT SHALL THE DIRECT VENDOR'S LIABILITY EXCEED THE PRICE PAID FOR THE PRODUCT FROM DIRECT, INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THE PRODUCT, DISK, OR ITS DOCUMENTATION.
