ATEL'S CPE MIMO
n41/n77/n78/B41 are HPUE 26 dBm ±2 dB ※ ※：n30/LTE B30/LTE B48 21 dBm ±2 dB
WB550-NA-00 North America 5G Sub-6: n2/n5/n7/n12/n14/n25/n30/n41/n48/n66/n71/n77/n78 LTE FDD: B2/B4/B5/B7/B12/B13/B14/B17/B25/B26/B29/B30/B66/B71 LTE TDD: B41/48 LAA: B46 WCDMA: B2/4/5 Module: Verizon & AT&T Certified We remind users here that changes or modifications not explicitly approved by the responsible party may cause users to lose the authority to operate the equipment.
Quick Start Guide Introduction The WB550 is a premium indoor 5G NR CPE, designed for 802.11a/b/ g/n/ac/ax dual band Wi-Fi access. The product provides optimized high throughput data and a wide area coverage network for residential, commercial and enterprise users, supporting multiple services. Customers enjoy reliable dual-band Wi-Fi AP functions, broadband access and hotspot Wi-Fi connections with the WB550.
I/O Panel of Router LED Panel of Router Packing List Make sure you have everything you need to properly configure the device.
Configure Hardware Insert SIM Card If you want to remove the SIM card, please lightly press the SIM card, the SIM card will pop out. Make sure the CPE is turned off before you insert or remove your SIM card. Otherwise, the CPE and SIM card may be damaged. Please insert your SIM card (3FF) as following: How does it Work The figure is just for reference only, please connect according to your requirements.
Step 1 Connect the supplied power adapter to the CPE. Step 2 Connect other devices. You can connect your computer or classic Switch via Ethernet cable to LAN port. You can connect your laptop via Wi-Fi. You can connect your telephone via TEL port. When you are using the CPE, you can adjust the position and direction of CPE to get stronger NR signal, you can judge from the NR signal LED indicators.
Configure The CPE Login to the Website Use a browser to access the management web page to configure and manage the CPE. The following procedure describes how to use a computer running Windows 7 or above version and Internet Explorer to connect to the CPE webpage. Step 1 Step 2 Connect the CPE correctly. Start Internet Explorer, go to http://192.168.1.1 in the address bar, and press Enter. Step 3 Enter the user name (admin) and password (admin), and click Log In.
Configuration of NR Step 1 Connect the CPE correctly. Step 2 Enter the management website. Step 3 Choose Settings → Network → NRSettings. Step 4 Set the connection mode and scan mode. The default setting is automatically connection and full band scanning,if you want to connect the LTE network according to your needs,you can set the connection mode as manual,and simply scan a specified band.
Configuration of Wi-Fi Step 1 Step 2 Connect the CPE correctly. Enter the management website. Choose Settings → Wi-Fi → WLAN Settings. In the General Settings, set Wi-Fi Enable or enable Wi-Fi with the Step 3 Step 4 Wi-Fi button. Step 5 In the Setting, change the SSID, such as "NR-Router" To ensure data security, it is recommended that you change Step 6 the Wi-Fi password by default. Step 7 Click Submit to save the settings.
Troubleshooting The POWER indicator does not turn on. Make sure that the power cable is connected properly and the CPE is powered on. Make sure that the power adapter is compatible with the CPE. Fails to login the web management page. Make sure that the CPE is started. Verify that the CPE is correctly connected to the computer through Wi-Fi or a network cable. The CPE fails to search for the wireless network. Check that the power adapter is connected properly.
Product Marketing Name (PMN)：ATEL 5G CPE FCC ID: XYO-WB550 IC ID: 20255-WB550 FCC Regulations ATEL 5G CPE complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, under Part 15 of the FCC Rules.
