LIBRA-04 M MANUAL COPY ROUTER LIBRA-04 M MANUAL COPY ROUTER User's Manual
LIBRA-04 M MANUAL COPY ROUTER TABLE OF CONTENTS ITEM # SUBJECT PAGE # I INTRODUCTION 3 II SAFETY APPLICATIONS 4 II.1 DESCRIPTION OF SYMBOLS USED IN THIS USER’S MANUAL 4 II.2 SAFETY INSTRUCTIONS 5 III MACHINE DESCRIPTION 8 III.1 TECHNICAL DESCRIPTION 9 III.2 TECHNICAL DATA 9 IV INSTALLATION 10 IV.1 MACHINE LIFTING AND MOVING 10 IV.2 THE REQUIRED OPERATION ZONE 11 IV.
LIBRA-04 M MANUAL COPY ROUTER I. GENERAL INFORMATION 1.1. INTRODUCTION The user’s manual given by the manufacturer contains necessary information about the machine parts. Each machine operator should read these instructions carefully, and the machine should be operated after fully understanding them. Safe and efficient use of the machine for long term depends on understanding and following the instructions contained in this manual.
LIBRA-04 M MANUAL COPY ROUTER II – SAFETY APPLICATION Before operating this equipment, be sure of reading and understanding the safety instructions. The operator may not run the machine without reading this guide. Reading and understanding this user guide is important for hindering to injury to the operator, third persons, animals, environment and/or damage to the machine. II.
LIBRA-04 M MANUAL COPY ROUTER This explains not be pulled up the protective parts. Do not operate without guards. This is high temperature symbol. II.2 – SAFETY INSTRUCTIONS Before operating this equipment, read the safety instructions and carry out them. This technical handbook should be accessible at all times at the site of operation of the machine. The operators who work during the installation, should read the machine guide. Be sure of understanding.
LIBRA-04 M MANUAL COPY ROUTER Use only original spare part. Don’t lean against control panel and do not force. Use e-Stop button when necessary for stopping the machine because very frequent repetition of this process, may cause problems on the some electric components. Service personnel of our company is responsible from the first operation of machine. Do not allowed to run the machine any other person.
LIBRA-04 M MANUAL COPY ROUTER Disconnect electrical power hydraulic and air pressure before making repairs or adjustments. Do not run the machine in the watery and moist areas. Machine should be adjusted and well-kept all the time. Never do not work with broken machine.
LIBRA-04 M MANUAL COPY ROUTER III –MACHINE DESCRIPTION LIBRA-04 M Manual Copy Router is used for milling lock holes, hinge slots, and handle mounting holes onto vinyl (PVC) and aluminum profiles.
LIBRA-04 M MANUAL COPY ROUTER IV – INSTALLATION The Libra-04 M Manual Copy Router is factory tested to ensure that the electrical system and all mechanical components work properly. All material and spare parts sent from the factory have been thoroughly checked before consignment to the transportation agency. On receiving the equipment, check for any damage which may have occurred during transportation. IV.1 – MACHINE LIFTING AND MOVING The equipment is delivered in its own special packing.
LIBRA-04 M MANUAL COPY ROUTER IV.2 – THE REQUIRED OPERATION ZONE ATech recommends a minimum of 100 cm (40”) clearance on the front, a minimum of 30 cm (12”) clearance at the back side of the entire assembly and a minimum of 150 cm (59”) clearance on the sides. The following figure shows the recommended minimum safe operation area. Figure 4-2 The settlement of machine IV.3 – MACHINE INSTALLATION and ASSEMBLY OF Ensure that the ground is even and level.
LIBRA-04 M MANUAL COPY ROUTER Pressure for air should read 6 to 8 bar (90-120 psi). Using hose with a large diameter may prevent loose of air pressure along the long line. Also the air should never contain moisture to not damage to the valves and pistons. Machine should be balanced. A good balanced machine increases production quality, decreases machine shake and makes simpler running the axes.
LIBRA-04 M MANUAL COPY ROUTER V – RUNNING THE MACHINE Figure 5-1 Machine parts 13 / 19
LIBRA-04 M MANUAL COPY ROUTER MILLING PROCESS Turn on the main power switch, put the profile onto the setsquare and clamp it with the clamping pistons. The tracer pin must be placed into the template which is to be copied. Copy motor is run. Set the drill bit (router bit) into profile by copy vertical movement handle. Deep drilling is adjusted with part. Drill the channel with copy movement knob. Slowly release the vertical copy movement handle after the process is completed. Milling cutters go up.
LIBRA-04 M MANUAL COPY ROUTER Electric cabinet should be cleaned from dust and shaving with air once in six months. • If clamp pistons do not press the profile, pressure should be controlled and adjusted from the conditioner. Machine needs at least 6 bar (90 psi) air pressure. Make sure to maintain this. VII – TABLE OF PROBABLE PROBLEMS AND THEIR SOLUTIONS VII.1 - WHEN PROBLEM OCCURS, THE PROCESSES THAT SHOULD BE DONE VII.
LIBRA-04 M MANUAL COPY ROUTER If the machine seems like normal completely, read the user guide again by running the machine with the method of finding out the breakdown step by step. If problem still occurs, call the service.
LIBRA-04 M MANUAL COPY ROUTER VIII – CIRCUIT DIAGRAM VIII.
LIBRA-04 M MANUAL COPY ROUTER VIII.
LIBRA-04 M MANUAL COPY ROUTER 19 / 19
