User's Manual

ManualsBrandsATEC ManualsLED & LCD TVs19" LCD Monitor

Before Use

English

● The size and appearance of this monitor may be changed for improvement without

notice.

● This user manual contains proprietary information that is protected by copyright.

All rights are reserved. No part of this user manual may be reproduced, photocopied,

transcribed, translated or transmitted in whatsoever from without the prior permission of

the manufacturer.

● Damage caused by using the unauthorized components or disregard of the information

and cautions in this user manual is not covered by the warranty service.

● If you have problem with your monitor, please check TroubleShooting in this user

manual before asking for help service center.

● The information in this user manual is subject to change without notice.

● If you let display the static images on the LCD monitor for prolonged time, the LCD

monitor may show you the screen images retention. It is not a continuous condition and

will fade away in a period time. The Image retention is a condition that may occur on all

LCD monitors.

● The LCD consists of about 5 million pixels. One pixel includes 3 dots and some of dots

could be seen bright and dark compared to other dots. Please, note that it may occur

on all LCD monitors and it is not a product inferiority.

Summary of content (26 pages)

PAGE 1
Before Use ● The size and appearance of this monitor may be changed for improvement without notice. ● This user manual contains proprietary information that is protected by copyright. All rights are reserved. No part of this user manual may be reproduced, photocopied, transcribed, translated or transmitted in whatsoever from without the prior permission of the manufacturer.
PAGE 2
English CE Conformity Notice The Product herewith complies with requirements of the Low Voltage Directive 73/23/EEC and the EMC Directive 89/336/EEC and carries the ‘CE’ mark accordingly.
PAGE 3
Unpacking After opening the box, make sure the following items are provided with the monitor. If you find that any of these items is missing or appears damaged, contact your dealer immediately.
PAGE 4
Instructions for Safety English ¢”Matters that demand special attention are divided into ‘Warning’ and ‘Caution’, and are detailed a follows. In case of the possibility that a serious injury or death may occur during a violation of the instructions. In case of the possibility that a slight injury or product damage may occur during a violation of the instructions. ¡ Don’t plug the power adapter into a non-grounding power outlet. ¡ Never touch the power plug with wet hands.
PAGE 5
English ¡ Keep the power cord from proximity to a heating instrument. The covering material of the cord may melt, causing a fire or electric shock. ¡ Grasp the power plug at the base to remove it from the wall, and pull firmly but gently. If you yank at the cord, the wire may be broken, causing ignition or heat generation. ¡ Pull the power cord out when the monitor is not used for a long time, or while you are away.
PAGE 6
English ¡ Don’t block or obstruct the air-flow holes of the monitor. A fire or damage of the monitor may be caused due to an increase in internal temperature. ¡ Don’t spill liquids such as chemicals, water on the monitor. A fire or electric shock accident may be caused. ¡ Never disassemble and repair the monitor but trained repair engineers. A fire or electric shock accident may be caused.
PAGE 7
English ¡ Place the monitor on a stable and secure surface. Fall or displacement of the monitor may cause an injury. ¡ Turn off the monitor and disconnect all cables from the monitor before moving the monitor. ¡ Be careful with the shock when moving the monitor. ¡ Don’t scratch or jolt the monitor surface. Damage or failure of the panel may be caused. ¡ Take hold of the monitor with both hands setting the panel forward.
PAGE 8
CONTENTS English Installing the Monitor 1.1 Features … … … … … … … … … … … … … … … … … … … … … … … … … … 1-1 1.2 Monitor Overview … … … … … … … … … … … … … … … … … … … … … … 1-2 Front Side … … … … … … … … … … … … … … … … … … … … … … … … … … 1-2 Rear Side … … … … … … … … … … … … … … … … … … … … … … … … … … 1-3 1.3 Connecting the Peripheral Devices … … … … … … … … … … … … … 1-4 Installing the Monitor Driver 2.
PAGE 9
1.1 Features Adopt the 19.0” LCD(Liquid Crystal Display) narrow bezel panel which allows you efficient use in a small space due to the slim design with wide screen. AUDIO It gives user an amplified stereo sound through internally installed speakers (2 W).
PAGE 10
1.2 Monitor Overview This section identifies the name of each component of the monitor and briefly describes the function of each component. Front Side LEFT Button TFT LCD Display Decreases the value of the selected item. (Decreases the volume without pressing the MENU Button.) Displays the current contents of the display. SELECT Button Selects the OSD menu item and the submenu item to be adjusted in the OSD menu window and save the modified value at any selected item.
PAGE 11
VIDEO Jack (Optional) USB UP Port (Optional) Connects the video cable to the VIDEO jack on the camcorder or VTR. Connects the USB cable to the USB connector on the computer. USB DOWN 4 Port (Optional) Connects USB devices. DVI Connector Connects the DVI cable to the DVI connector on the computer. (In case using ANALOG in DVI model monitor, you must set up the adaptor as shown on the illustration.) TV Tuner (Optional) Connects the TV antenna cable.
PAGE 12
1.3 Connecting the Peripheral Devices Turn off the monitor, computer and other peripheral devices before connecting the monitor and peripheral devices. 1 Connecting the power Plug into the power outlet at 220V or 110V. (The voltage is set utomatically.) DC Adapter Power Cord DC-IN Jack 2 Connecting the computer Connect the VGA cable to the VGA connector or the DVI cable to the DVI connector on the computer.
PAGE 13
Connecting Audio Devices AUDIO OUT Jack Connect the audio cable to the AUDIO IN jack on the monitor and the LINE OUT jack on the computer or connect the audio cable (RCA) cable to the AUDIO IN jack on the monitor and the stereo jack on the camcorder/TV and connect a set of headphones or external speakers to the AUDIO OUT Jack.
PAGE 14
5 Connecting the TV Antenna TV Tuner (Optional) TV Antenna Cable 6 Connecting USB Devices (Optional) At first, connect the USB cable to the USB UP port on the monitor and USB connector on the computer and then, connect USB devices to the USB DOWN port on the monitor.
PAGE 15
2.1 Installing the Monitor Driver Under Windows This section shows how to install the monitor driver under Windows or Linux by using the monitor driver diskette provided. To install the monitor driver, please refer to your OS in this section. Windows XP Turn on the computer and the monitor. Insert the monitor driver diskette into the FDD on the computer. Click the Start button on the Windows display and select Control Panel. Double click the Display icon in the Control Panel window.
PAGE 16
2.2 Installing the Monitor Driver Under Linux Linux 1 You’d make xf86config file to run X-Window. Your monitor is surely and easily configured with this file. This file will be made as running xf86config. 2 Press Enter in the first and second window after running xf86config file. 3 In third window, we come up with the mouse setting window. 4 Configure it as opt for user system. 5 Next will be the screen for selecting Keyboard. 6 Configure it as opt for user system.
PAGE 17
3.1 Selecting and Adjusting the OSD(On Screen Display) Menu You can select the OSD menu in the OSD window by using all the control buttons under the display. To change the current settings or adjust it to what you prefer, please follow these steps.
PAGE 18
3.2 OSD(On Screen Display) Menu Functions OSD Main Menu The OSD main menu window that you can select and adjust the OSD menu to the optimal display appears by pressing the MENU button. MICOM Version Screen Resolution ¡ Screen Frequency SETUP Controls the OSD position, OSD time, and input source of the display. ¡ BRIGHTNESS/CONTRAST Controls the brightness and contrast of the display. ¡ COLOR Changes the value of the display color(Red, Green, Blue).
PAGE 19
COLOR RED : Changes the value of red. GREEN : Changes the value of green. BLUE : Changes the value of blue. EXIT : Exits COLOR menu. POSITION HORIZONTAL : Adjusts the horizontal position of the display. VERTICAL : Adjusts the vertical position of the display. CLOCK : Increases or decreases the number of pixel to adjust the horizontal size. PHASE : Adjusts the focus and clarity of the display. EXIT : Exits POSITION menu. OSD POSITION : Adjusts the position of the OSD window.
PAGE 20
Caution (It’s different by the product option.) When you press the SELECT button in Windows display, the current input source will be appeared and it will be switched to ANALOG ▶ DIGITAL ▶ COMPOSITE ▶ S-VIDEO ▶ TUNER(Optional) by pressing the SELECT button every two times continuously. The screen will be blanked unless the input source is correct. Select the proper input source according to the display device you connect.
PAGE 21
CHANNEL MENU OSD (PAL/SECAM) CHANNEL MENU CHANNEL OSD ¡ AUTO PROGRAM : Automatically memorize all ¡ CHANNEL OSD is displayed on the right-top position. the active channels. ¡ MANUAL PROGRAM : Manually change the program number and name. ¡ PROGRAM EDIT : Edit the program number and name. AUTO PROGRAM AUTO PROGRAM START MANUAL PROGRAM : SYSTEM ¡ SYSTEM : Select the TV SYSTEM.
PAGE 22
MANUAL PROGRAM : CHANNEL ¡ CHANNEL : Select the AIR or the CATV. - C-CH : AIR TV - S-CH : CABLE TV ¡ UP/DOWN KEY : Select the C-CH or the S-CH. Select the channel number. ¡ LEFT/RIGHT KEY : Select the CHANNEL menu. MANUAL PROGRAM : FINE MANUAL PROGRAM : SEARCH ¡ FINE : Adjust when the display image is blurred or unfocused. ¡ SEARCH : Search the next channel signal (CHANNEL and NAME are updated after search). MANUAL PROGRAM : NAME ¡ NAME : Save the channel name.
PAGE 23
MANUAL PROGRAM ¡ STORE : Save the channel to the selected number (Default : the present number). PROGRAM EDIT ¡ UP/DOWN KEY : select the Program. ¡ Function select : “1”, “2”, “3”, “4” (AUTO button is toggling ; 1(DEL) ▶ 2(COPY) ▶ 3(MOVE) ▶ 4(SKIP) ▶ 5(EXIT) ▶ cancel) ¡ DEL : Delete the Program (select the program ▶ ex) Delete PR 0 1▶ PROGRAM EDIT : COPY SELECT). ex) Copy PR6 from PR3 ¡ COPY : Copy the Program (select the source program ▶ 2 ▶ select the destination program ▶ SELECT).
PAGE 24
PROGRAM EDIT : MOVE ex) Move PR4 to PR8 ¡ MOVE : Move the Program (select the source program ▶ 3 ▶ select the destination program ▶ SELECT). PROGRAM EDIT : SKIP ex) Skip PR8 ¡ SKIP : Skip the Program (select the program ▶ 4 ▶ SELECT). ¡ When you use the SKIP function, the skipped channel is not selected during up and down. ¡ The SKIP function is toggling to the ADD.
PAGE 25
A.1 Troubleshooting Please check the below particulars before you contact the service center to notify an abnormality of the monitor. Is the monitor power cord inserted? Please connect the power cord correctly to the concent. Is the power turned off? Please press the power button. Is the power turned on and the power pilot lamp blinking amber? The monitor is in the power saving mode. Please therefore move the mouse or press any key on the keyboard.
PAGE 26
A.2 Specification The details of product specification can be changed without notice to improve the product. LCD Type Size Pixel Pitch Contrast Ratio Color depth Luminance, white Frequency Maximum Horizontal frequency Vertical frequency View Angle(H/V) input signal Audio Output Signal Input input connector User’s control a-Si active matrix TFT-LCD 19.0 (481.84 mm) 0.294 mm x 0.294 mm 400 : 1(typical) 8 bit(16,777, 216 Color) 250 cd/m2 SXGA 1280 x 1024 31.