Bench Press Shop Presses Operating Instructions & Parts Manual Model Number Atd-7452 Atd-7453 Atd-7454 Atd-7455 (Bench Press) (Atd-7454 shown) ! Capacity 12 Ton 12 Ton 20 Ton 25 Ton (Atd-7455 shown) This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death. ! advertencia • Leer, comprender, y seguir las instrucciónes antes de utilizar el aparato.
SAFETY and GENERAL INFORMATION Save these instructions. For your safety, read, understand, and follow the information provided with and on this product before using. The owner and operator of this equipment shall have an understanding of this product and safe operating procedures before attempting to use. The owner and operator shall be aware that use and repair of this product may require special skills and knowledge.
PREPARATION Before Use 1. Verify that the product and application are compatible, if in doubt call Atd Tools technical service (636) 3279050. 2. Before using this product, read the operator's manual completely and familiarize yourself thoroughly with the product, its components and recognize the hazards associated with its use. 3. To familiarize yourself with basic operation of bottle jack (use the notched or stamped end of provided handle to engage) or hand pump and turn the release valve: a.
Assembly Model Atd-7454: (Refer to Figure 3) Size of Hardware Kits 3 bolt M10x25 lock washer M10 nut M10 9 nut M8 11 bolt M16x150 flat washer M16 lock washer M16 nut M16 13 bolt M10x25 lock washer M10 square washer M10 14 bolt M10x130 lock washer M10 nut M10 Note: Do not tighten any bolts unless told to do so. 1. Attach base legs (1) to upright channels (2) with bolts, lock washers and nuts (3). Hand tighten only. 2.
Ram Hydraulic Couplers (1/4" NPT) Upper Cross Member Hydraulic Hose Bearing Punch Pump Handle Release Valve Hand Pump Oil Filler Screw Pump Bracket Bed Frame Support Pin Arbor Plate Support Link Upright Channel Base Leg Lower Cross Member Assembly Models Atd-7455: (Refer to Figure 5) Figure 4 - Shop Press Components (Atd-7455 shown) Note: Do not tighten any bolts unless told to do so. 1. Attach base legs (1) to upright channels (2) with bolts, lock washers and nuts (3). Hand tighten only. 2.
! WARNING • Study, understand, and follow all printed materials provided with/on this product before use. • Always use an adequately rated, calibrated load cell with digital indicator to monitor pressing force! • Do not exceed rated capacity. • Use the device only on a hard, level surface. • Always wear safety goggles when working on or near this equipment. • Keep hands, feet and all other body parts away from loading area. • Never leave loaded press unattended.
Unlike presses equipped with a separately mounted pump, the power unit on this press can not be equipped with a pressure gauge, therefore monitoring the load must be done by other means, such as a load cell w/ digital indicator. Whatever means is chosen, the load measuring means shall be calibrated annually. ! The hydraulic power unit provided with this device is intended to be used as an integral part of this press and not as a stand-alone jacking device separate of the press.
Replacement Parts illustration for models Atd-7452, Atd-7453 & Atd7454 Item 1 2 3 4 5 6 7 8 9 10 11 12 13 14 - Part# for model: Atd-7452 & Atd-7453 Atd-7454 T060-05000-000 T126-00003-000 T060-00001-100 T060-00002-100 B120-10000-000 B200-10000-000 T060-04000-000 T126-02000-000 B080-20000-000 T126-03000-000 T060-00003-100 T126-00001-000 T060-02000-000 T125-01000-000 T184-00004-000 T060-00006-000 T184-00005-000 T060-03000-000 T125-02000-000 T060-01000-100 T184-00006-000 T184-00007-000 T125-00007-000 T126-0100
Replacement Parts illustration for model Atd-7455 Item Part# for model: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 T125-00001-000 T125-00003-000 T125-00007-000 T125-02000-000 T125-01000-000 T125-00002-000 T184-00006-000 T184-00004-000 T184-00005-000 T184-00003-000 F100-90004-K01 T125-00008-000 F040-90107-K02 T125-03000-000 F250-30000-000 F040-90009-K04 F040-90009-K05 F100-90009-K01 55255 T125-04000-000 16 17 - Description Qty Upper Cross Member Punch Arbor Plates (pair) Bed Frame Support Pin Upright Channel
TROUBLESHOOTING Symptom Possible Causes Corrective Action • Release valve not tightly closed • Overload condition • Faulty/ Loose couplers • Oil lever in pump is low • Ensure release valve tightly closed • Remedy overload condition • Replace/ Tighten couplers • Fill and bleed system Ram bleeds off after press operation • Release valve not tightly closed • Oil lever in pump is low • Ram or Bottle Jack malfunction • Ensure release valve tightly closed • Fill and bleed system • Contact Atd Tools Tech.
ONE YEAR LIMITED WARRANTY For a period of one (1) year from date of purchase, Atd Tools Inc. will repair or replace, at its option, without charge, any of its products which fails due to a defect in material or workmanship, or which fails to conform to any implied warranty not excluded hereby. Performance of any obligation under this warranty may be obtained by returning the warranted product, freight prepaid, to Atd Tools Inc. Warranty Service Department, 160 Enterprise Drive, Wentzville, MO 63385.
Notes Atd Tools Inc. 160 Enterprise Drive, Wentzville, MO 63385 Tel: (636)327-9050 Fax: (636)327-9046 www.atdtools.
