Quick start guide TL92278/TL92328/TL92378 DECT 6.
Installation You must install and charge the handset battery before using the cordless handset. STOP! See pages 4-5 for easy instructions. Install the telephone base close to a telephone jack and a power outlet not controlled by a wall switch. The telephone base can be placed on a flat surface or vertically mounted on the wall. For optimum range and better reception, place the telephone base in a central and open location.
Telephone base installation Install the telephone base as shown below. Make sure that the electrical outlet is not controlled by a wall switch. If you subscribe to high-speed Internet service (digital subscriber line - DSL) through your telephone line(s), you must install a DSL filter between the telephone base and the telephone wall jack. The filter prevents noise and caller ID problems caused by DSL interference. Please contact your DSL service provider for more information about DSL filters.
Charger installation Plug the power adapter into an electrical outlet not controlled by a wall switch. IMPORTANT INFORMATION 1. Use only the power adapter(s) supplied with this product. To order a replacement power adapter, visit our website at www.telephones.att.com, or call 1 (800) 222-3111. In Canada, dial 1 (866) 288-4268. 2. The power adapters are intended to be correctly oriented in a vertical or floor mount position.
Battery installation & charging Install the battery as shown on the next page. Once you have installed the battery, the screen indicates the battery status (see table below). If necessary, place the handset in the telephone base or charger to charge the battery. For best performance, keep the handset in the charger when not in use. The battery is fully charged after 16 hours of continuous charging. See the table on Technical specifications page of the user's manual for battery operating times.
Battery installation & charging Install the battery as shown below. After installing the battery, you can make and receive short calls. Place the handset in the telephone base or charger when not in use. For optimal performance, charge the handset battery for at least 16 hours before use. See the table on page 95 of the user's manual for battery operating times. Step 1 Press the depression and slide the battery compartment cover downwards (if necessary).
Bluetooth setup NOTE: Only one Bluetooth device can be paired with the telephone base at a time. HANDSET 1 To use a Bluetooth-enabled cellular phone with your telephone, you must first pair and connect your Bluetooth cellular phone with the telephone base. Pairing a device Before you begin, make sure that your Bluetoothenabled cellular phone is not connected to any other Bluetooth device. Refer to your cellular phone user's manual to learn how to search for or add new Bluetooth devices.
Bluetooth setup Turning off the auto connection If you do not want the telephone base to reconnect to a paired device automatically after it is disconnected, you can turn off the auto connection feature manually. In order to turn off the auto connection, you will need to initiate a disconnection from the paired cellular phone; this will transmit a signal to the telephone base and disable the auto connection.
Quick reference guide - handset CHARGE indicator On when the handset is charging in the telephone base or charger. DIR / MENU/SELECT Press to display the menu. While in the menu, press to select an item or save an entry or setting. CID Press DIR to display directory entries. Press to scroll up while in menus. While entering names or numbers, press to move the cursor to the right. Press to increase the listening volume when on a call. DELETE/MUTE During a call, press to mute microphone.
Quick reference guide - handset Feature menu The > symbol highlights a menu item. >DIRECTORY CALL LOG Menu Feature menu Using menus DIRECTORY CALL LOG INTERCOM RINGER VOLUME RINGER TONE KEY TONE LANGUAGE CLR VOICE MAIL HOME AREA CODE Press or to scroll through menu items. Press MENU/SELECT to select or save changes to a highlighted menu item. Press OFF/CLEAR to cancel an operation, back up to the previous menu, or exit the menu display. For complete instructions, please refer to the user’s manual.
Quick reference guide - telephone base IN USE indicator On when the handset is in use, when the answering system is answering an incoming call or when you are registering a handset. Flashes when another telephone is in use on the same line, or when you are deregistering handset(s) from the telephone base. VOICEMAIL indicator Flashes when you have new voicemail. Voicemail is a service offered by your local telephone company, and is different from answering system messages.
www.telephones.att.com The Bluetooth® word mark and logos are owned by Bluetooth SIG, Inc. and any use of such marks by Advanced American Telephones and its parent, VTech Holdings Limited, is under license. VTech Holdings Limited is a member of Bluetooth SIG, Inc. Other trademarks and trade names are those of their respective owners. © 2008-2009 Advanced American Telephones. All Rights Reserved.