Installation guide

CIB 2885
(14A) 5-BUTTON VOICE TERMINAL FIXED DESK STAND AND WALL MOUNT (32000)
●
●
This bracket supports a 7302 Voice Termi-
nal either on a desk or mounted on a wall.
The original package contains:
The desk stand/wall mount (unas-
sembled).
Fasteners and screws appropriate for
wall mounting.
The pieces of the desk stand/wall mount
come attached to a disposable runner (see
Figure 1). The WALL SUPPORT and DESK
SUPPORT designations are imprinted on
the appropriate plastic part. Separate as-
sembly instructions are provided for each
application. Skip to the appropriate “In-
struction” section and proceed.
DESK
SUPPORT
BASE
WALL
SUPPORT
RUNNER
FEET (BONDED TO
CARRIER STRIP)
Figure 1
MOUNTING
TAB
SLOTS
A
TAB
B
5-BUTTON
VOICE
TERMINAL
DESK
SUPPORT
BASE
FOOT
DESK INSTALLATION
A
B
C
D
RED KEY
WALL
MOUNT
E
WALL MOUNT
WALL
SUPPORT
MOUNTING
SCREW HOLES
TAB
A
TAB
B
Figure 2
DESK STAND ASSEMBLY AND IN-
STALLATION
Break the pieces away from the run-
1.
2.
3.
4.
5.
6.
ner.
Locate the DESK SUPPORT and BASE
pieces. File the rough edges off the
pieces where they were attached to
the runner.
Peel the self-stick feet off the carrier
strip, and press them into position at
the corners of the base.
Set the base on its feet.
Insert Tabs A and B of the desk sup-
port into Slots A and B of the base
(see Figure 2).
Turn the voice terminal over and rest it
on a desk or table.
Position the stand on the voice termi-
nal so that the stand’s mounting slots
fit just below the mounting tabs of the
voice terminal.
Gently slide the stand upward so that
the voice terminal tabs fit securely in
the three mounting slots on the stand.
Press down on the stand to depress
the locking tab.
Turn the voice terminal over and place
on desk or table (see Figure 3).
WALL MOUNT ASSEMBLY AND INSTALLA-
TION
Assembly Instructions
7.
8.
9.
1.
2.
3.
4.
5.
1.
Break the pieces away from the run-
ner.
Locate the WALL SUPPORT and BASE
pieces. File the rough edges off the
pieces where they were attached to
the runner.
Place the base upside down on a table
or desk.
Insert Tabs A and B of the wall support
into Slots A and B on the base.
Lift base and push wall support through
slots until it clicks into place (see Fig-
ure 4).
Figure 3
Figure 4
Installation Instructions
Note: Be sure to select a location for
installation at least as large as
the voice terminal.
Select the Installation location: using
the bracket as a template, mark the
four mounting screw locations.
Select proper toggler for wall thickness
or wall type:
●
For walls 3/8-inch to 1/2-inch
thick, select the smaller of the two
sizes provided.
●
For walls 5/8-inch to 3/4-inch thick,
select the larger of the two sizes pro-
vided.
● For solid walls, either of the two sizes
may be used.
Drill four holes at the four toggler
mounting locations, using a 5/16-inch
diameter drill.
Fold and insert a toggler (Figure 5A) in
each of the mounting locations. Tap
each toggler flush to wall (Figure 5B).
2.
3.
4.
5.
6.
7.
8.
9.
Figure 5
Pop the anchor open with the red key
— do not hammer the key (see Figure
5C).
Using a small drill bit, enlarge the four
mounting holes in the wall mount.
Insert the top two screws into the wall
mount and partially thread the screws
into the starter holes of the togglers
(Figure 5D).
Insert the two remaining screws into
the lower mounting holes (see Figure
5E).
Tighten all four screws securely.