91-000341-030-000-E560-1 Manual July.11,05.qxd User Manual (Part 2) 5.
91-000341-030-000-E560-1 Manual July.11,05.qxd You must charge the battery and register the handset before use. STOP! For customer service or product information, visit our web site at 2/13/1950 7:21 PM See pages 2-3 for easy instructions. Please also read Important Product www.telephones.att.com Information Enclosed in product package. or call 1-800-222-3111. Table of contents Before you begin........................................1 Parts checklist ............................................
91-000341-030-000-E560-1 Manual July.11,05.qxd 2/13/1950 7:21 PM Before you begin This cordless telephone operates with the maximum power allowed by the Federal Communications Commission (FCC). Even so, this handset and base can communicate over only a certain distance — which can vary with the locations of the base and handset, the weather, and the construction of your home or office.
91-000341-030-000-E560-1 Manual July.11,05.qxd 2/13/1950 7:21 PM Battery & charger installation After installation, place the handset in the charger and allow the battery to charge for 15 hours before use.You can keep the battery charged by returning the handset to the charger after each use. When battery power is fully depleted, a full recharge takes about 12 hours.
91-000341-030-000-E560-1 Manual July.11,05.qxd 2/13/1950 7:21 PM Registration Before using a new E560-1 handset, you must register it with the E5633/ E5630/E5603B/E5600 base. During registration, you must enter the 15-digit ID number of the telephone base.The Base ID is located on the bottom of the base unit. Enter base ID, then press SELECT. The handset provided with your E5600/E5630 is automatically registered as Handset 1.
91-000341-030-000-E560-1 Manual July.11,05.qxd 2/13/1950 7:21 PM Replacing a Handset If you are replacing a handset on a system that has the maximum number of handsets registered (4), or wish to change the assigned handset number of your registered handsets, you must first de-register the handsets, then re-register all handsets. De-Register All Handsets • Unplug the power supply from the base unit. (E5634B/E5633/E5630/E5603B/E5600) • Remove all handsets from the charge cradles and base.
91-000341-030-000-E560-1 Manual July.11,05.qxd 2/13/1950 7:21 PM Re-Registering a Handset You can re-register handsets after de-registering from the base. Or you can re-register handsets to a new base unit, if you have replaced your base unit for any reason. To re-register a handset: • Make sure your handset batteries are properly installed and charged. • Your handset will display “SEARCHING...”. • Press and hold the SELECT key until the handset displays “ENTER BASE ID”.
91-000341-030-000-E560-1 Manual July.11,05.qxd 2/13/1950 7:21 PM Belt clip & optional headset Install belt clip as shown below if desired. For hands-free telephone conversations, you can use any industry standard 2.5 mm headset (purchased separately). For best results use an AT&T 2.5 mm headset. Snap belt clip into notches on side of handset. Rotate and pull to remove. Plug 2.
1-000341-030-000-E560-1 Manual July.11,05.qxd 2/13/1950 7:21 PM Quick reference guide For complete instructions, please refer to the manual provided with your E5634B, E5633, E5630, E5603B or E5600 telephone. Handset V Select/Menu Press to display menu, or to select highlighted item from menu. CID Press to scroll down in menus. Press when phone is not in use to display Caller ID information . While entering names, press to move the cursor to the left. ^ PHONE BOOK Press to scroll up in menus.
91-000341-030-000-E560-1 Manual July.11,05.qxd 2/13/1950 www.telephones.att.com Copyright © 2004 Advanced American Telephones. All Rights Reserved. AT&T and the Globe Design are trademarks of AT&T Corp., licensed to Advanced American Telephones. Printed in China. Issue 5 AT&T 07/05.
