Cordless Telephone User Manual

ManualsBrandsAT&T ManualsCordless TelephoneE2662B

User Manual (Part 2)

2.4 GHz Expansion

Handset E262

For use with AT&T

model E2562 / E2662B

91-5676-10-00_E262Manual_R0FEB2704.qxd 2/27/2004 12:41 PM Page 1

Summary of content (8 pages)

PAGE 1
91-5676-10-00_E262Manual_R0FEB2704.qxd 2/27/2004 User Manual (Part 2) 2.
PAGE 2
91-5676-10-00_E262Manual_R0FEB2704.qxd You must charge the battery and register the handset before use. 2/27/2004 STOP! 12:41 PM Page 2 See pages 2-3 for easy instructions. For customer service or product information, visit our web site at Please also read www.telephones.att.com or call 1-800-222-3111. Enclosed in product package. Important Product Information Table of contents Before you begin........................................1 Parts checklist.............................................
PAGE 3
91-5676-10-00_E262Manual_R0FEB2704.qxd 2/27/2004 12:41 PM Page 1 Before you begin This cordless telephone operates with the maximum power allowed by the Federal Communications Commission (FCC). Even so, this handset and E2562 / E2662B base can communicate over only a certain distance — which can vary with the locations of the base and handset, the weather, and the construction of your home or office. If you move out of range during a phone conversation, you might hear noise or interference.
PAGE 4
91-5676-10-00_E262Manual_R0FEB2704.qxd 2/27/2004 12:41 PM Page 2 Battery & charger installation After installation, place the handset in the charger and allow the battery to charge for 12 hours before use. You can keep the battery charged by returning the handset to the charger after each use. When battery power is fully depleted, a full recharge takes about 8 hours. LOW BATTERY RDL MENU MEM Low battery indicator Return handset to charger when this symbol flashes.
PAGE 5
91-5676-10-00_E262Manual_R0FEB2704.qxd 2/27/2004 12:41 PM Page 3 Registering the handset Enter base ID, then press OK. R ENTER BASE ID 123456789012345 < OK Before using your new handset, you must register it with the E2562 / E2662B base. During registration, you must enter the 15-digit ID number of the telephone base. To find this number, go to the base, press MENU, scroll down to select DISPLAY BASE ID, then press OK.
PAGE 6
91-5676-10-00_E262Manual_R0FEB2704.qxd 2/27/2004 12:41 PM Page 4 Belt clip & optional headset Install belt clip as shown below if desired. For hands-free telephone conversations, you can use any industry standard 2.5 mm headset (purchased separately). For best results use an AT&T 2.5 mm headset. Snap belt clip into notches on side of handset. Rotate and pull to remove. Plug 2.5 mm headset into jack on side of handset (beneath small rubber cap).
PAGE 7
91-5676-10-00_E262Manual_R0FEB2704.qxd 2/27/2004 12:41 PM Page 5 Quick reference guide For complete instructions, please refer to the manual provided with your E2562 / E2662B telephone. Off/Clear Softkeys Press a softkey to select a menu item displayed just above the key. During a call, press to hang up. While using menus, press to cancel an operation, back up to the previous menu, or exit the menu display.
PAGE 8
91-5676-10-00_E262Manual_R0FEB2704.qxd 2/27/2004 12:41 PM www.telephones.att.com Copyright © 2004 Advanced American Telephones. All Rights Reserved. AT&T and the Globe Design are trademarks of AT&T Corp., licensed to Advanced American Telephones. Printed in China. Issue 1 AT&T 02/04.