- American Telephone & Telegraph Cordless Telephone User's Manual E2555, E2525, E2600B

ManualsBrandsAT&T ManualsCordless TelephoneE2600B

User Manual (Part 2)

2.4 GHz Expansion

Handset E250

For use with AT&T models

E2555 • E2525 • E2600B

91-5661-20-00.E250.R0.qxd 02/13/1950 19:21 Page 1

Summary of content (8 pages)

PAGE 1
91-5661-20-00.E250.R0.qxd 02/13/1950 19:21 User Manual (Part 2) 2.
PAGE 2
91-5661-20-00.E250.R0.qxd 02/13/1950 Youmustcharge batteries and register the handsetbeforeuse. 19:21 Page 2 STOP! Seepages2-3 for easy instructions. For customer service or product information, visit our web site at Please also read www.telephones.att.com or call 1-800-222-3111. Enclosed in product package. ImportantProductInformation Table of contents Before you begin........................................1 Parts checklist.............................................
PAGE 3
91-5661-20-00.E250.R0.qxd 02/13/1950 19:21 Page 1 Before you begin This cordless telephone operates with the maximum power allowed by the Federal Communications Commission (FCC). Even so, this handset and base can communicate over only a certain distance — which can vary with the locations of the base and handset, the weather, and the construction of your home or office. For best performance, keep the base antenna fully upright.
PAGE 4
91-5661-20-00.E250.R0.qxd 02/13/1950 19:21 Page 2 Battery installation & charging Install batteries as shown, then place the handset in the charger for at least 8 hours before use. You can keep batteries charged by returning the handset to the charger after each use. When battery power is fully depleted, a full recharge takes about 6 hours. LOW BATTERY REDIAL MENU MEM Low battery indicator Return handset to charger to recharge when this symbol flashes. (Handset will beep when battery is low.
PAGE 5
91-5661-20-00.E250.R0.qxd 02/13/1950 19:21 Page 3 Registering the handset Enter base ID, then press OK. R ENTER BASE ID 123456789012345 < OK Before using your new handset, you must register it with the base. During registration, you must enter the 15-digit ID number of the telephone base. To find this number, go to the base, press MENU, scroll down to select DISPLAY BASE ID, then press OK. The handset provided with your telephone is automatically registered as Handset 1.
PAGE 6
91-5661-20-00.E250.R0.qxd 02/13/1950 19:21 Page 4 Belt clip & optional headset Install belt clip as shown below if desired. For hands-free telephone conversations, you can use any industry standard 2.5 mm headset (purchased separately). For best results use an AT&T 2.5 mm headset. Snap belt clip into notches on side of handset. Rotate and pull to remove. Plug 2.5 mm headset into jack on side of handset (beneath small rubber cap).
PAGE 7
91-5661-20-00.E250.R0.qxd 02/13/1950 19:21 Page 5 Quick reference guide For complete instructions, please refer to the manual provided with your telephone. Softkeys Press a softkey to select a menu item displayed just above the key. Off/Clear During a call, press to hang up. Item 1 Item 2 Item 3 While using menus, press to cancel an operation, back up to the previous menu, or exit the menu display. Phone/Flash Press to begin a call, then dial a number.
PAGE 8
91-5661-20-00.E250.R0.qxd 02/13/1950 19:21 Page 6 www.telephones.att.com Copyright © 2004 Advanced American Telephones. All Rights Reserved. AT&T and the Globe Design are trademarks of AT&T Corp., licensed to Advanced American Telephones. Printed in China. Issue 2 AT&T 06/04.