©2009 Advanced American Telephones. All Rights Reserved. AT&T and the AT&T logo are trademarks of AT&T Intellectual Property licensed to Advanced American Telephones, San Antonio, TX 78219. Printed in China. Issue 3 AT&T 09/09 www.telephones.att.com User’s manual Part 2 SB67128 DECT 6.0 Repeater This manual contains information about this product’s installation and operation. Please also read Part 1 - Important product information. For customer service or product information, visit our website at www.
Before you install Parts list • • • • • SB67128 DECT 6.0 repeater Power adapter Part 1 Important product information Part 2 User’s manual Package of screws Use only the power adapter supplied with this product. To obtain a replacement, visit our website at www.telephones.att.com or call 1 (888) 915-2007. In Canada, dial 1 (866) 288-4268.
About the repeater You can use a repeater to extend the operating range for the AT&T SB67118 DECT 6.0 4-line corded/cordless telephone system to cover areas where the signal is very weak or not available. The repeater extends the range in all directions, even going around certain barriers. The telephone base, cordless handsets and repeaters are linked through wireless connections. When configured properly, you should not notice any reception problems as you move around within the covered area.
Registration You should register your repeaters to the telephone base before choosing locations for them in the building. NOTE: You can register a repeater to an SB67118 telephone base without deregistering it from a previous telephone base. New registrations overwrite any previous repeater registrations. Repeater registration 1. Plug in the repeater to AC power. The STATUS indicator light on the repeater flashes slowly. 2. Press and hold the SETUP button at the bottom of the repeater for two seconds.
Registration STATUS indicator light Slow flash The repeater is powered on and in idle mode waiting to be reregistered. -ORThe registered repeater is not connected to the telephone base. -ORYour telephone base has no power. Quick flash The repeater is registering to the telephone base. On The repeater is successfully registered and in a normal operation mode. Off The repeater has no power.
Installation After you have plugged in your repeaters in the locations you think are best, place a call from a cordless handset (AT&T SB67108) and while talking, move around the building to test the reception. You may want to adjust the position of repeaters to receive the best reception. Plug the small end of the power adapter into the power jack on the front of the repeater and route the cord through the slot on the bottom of the repeater.
Installation You can place the repeater on a tabletop. You can install your repeater on a wall or other object with the provided screws. Please use the recommended placement and installation tips as follows: • The antennas needs to be in a high location (not on the floor or under a desk) for reception. • Maintain a minimum of 30 feet distance between each repeater. • See page 2 for additional placement information.
Installation If you want to install your repeater on a wall or other object, use the provided screws. Professional assistance may be required to install screws on the wall. Then plug the large end of the power adapter into a nearby electrical wall outlet and raise the antennas. ^ ^ Screw holes Screw spacing=2.
Troubleshooting If you have difficulty operating this repeater, try the suggestions below. To contact Customer Service, purchase accessories or obtain replacement parts, visit our website at www.telephones.att.com or call 1 (888) 915-2007. In Canada, dial 1 (866) 288-4268. Please retain your receipt as your proof of purchase. My repeater doesn’t work at all. • Make sure the power cord is securely plugged in. • Make sure the STATUS indicator light is on.
Troubleshooting My repeater cannot register to my telephone base. • First try all the suggestions on the previous page. • Make sure your telephone base is model AT&T SB67118 DECT 6.0 4-line corded/cordless telephone system. • Carefully follow the registration instructions on pages 3 of this user’s manual. • Make sure your telephone base is within 950 feet of the repeater. If registration does not work, place the repeater next to the base and try registering again.
General product care To keep the repeater working and looking good, follow these guidelines: • Avoid putting it near appliances and devices that generate electrical noise (motors, fluorescent lights, etc.) • DO NOT expose it to direct sunlight or moisture. • Avoid dropping the repeater. • Clean with a soft cloth. • Never use a strong cleaning agent or abrasive powder because this will damage the finish. • Retain the original packaging in case it is necessary to ship it at a later date.
Technical specifications RF frequency band 1921.536 MHz — 1928.448 MHz Channels 5 Operating temperature 32°F — 122°F 0°C — 50°C Repeater voltage (AC voltage, 60Hz) 110 — 120 Vrms Repeater voltage (AC adapter output) 6VDC @600mA Repeater operating range This repeater operates within the maximum power allowed by the Federal Communications Commission (FCC).
