User`s manual

ManualsBrandsAT&T ManualsCordless TelephoneCL84350

Telephone operation

Operation Steps

Making a call Using a cordless handset:

Press PHONE or /SPEA�ERSPEA�ER -> Enter the telephone number.

Using the telephone base:

Press SPEA�ER or lift the corded handset -> Enter the

telephone number.

On-hook dialing

(predialing)

Using a cordless handset:

Enter the telephone number -> Press PHONE or

/SPEA�ERSPEA�ER to call.

Using the telephone base:

Enter the telephone number -> Lift the corded handset or

press SPEA�ER .

Answering a call Using a cordless handset:

Press PHONE or /SPEA�ERSPEA�ER, or press any dialing key

(0-9, TONE or #).

Using the telephone base:

Lift the corded handset, press SPEA�ER , or press any

dialing keys (0-9, TONE or #).

Ending a call Using a cordless handset:

Press OFF or return the handset to the charger.

Using the telephone base:

Hang up the corded handset or press SPEA�ER .

Handset

speakerphone

Using a cordless handset:

During a call, press /SPEA�ERSPEA�ER to switch between

handsfree speakerphone and normal cordless handset use.

Using the telephone base:

During a call, press SPEA�ER to switch between

handsfree speakerphone and normal corded handset use.

Redial Using a cordless handset:

Press REDIAL repeatedly to select the desired entry

-> PHONE or /SPEA�ERSPEA�ER to call.

Using the telephone base:

Press REDIAL repeatedly to select the desired entry

-> SPEA�ER or lift the corded handset to call.

Volume control Using a cordless handset:

Press -VOLUME to decrease or press VOLUME+ to increase

the listening volume during a call.

Using the telephone base:

Press qVOLUME to decrease or press VOLUMEp to

increase the listening volume during a call.

Call waiting

(Requires subscription

from telephone

service provider)

Press FLASH on the handset or FLASH on the telephone

base to put the current call on hold and take the new call;

press again to switch back and forth between calls.

Caller ID

This product supports caller ID services offered by most telephone service providers.

The telephone stores caller ID information of the last 50 incoming calls in the

telephone base. This information is common to all devices.

Missed call indicator

When a handset or the telephone base is in idle mode and has new or missed

calls, its screen shows XX Missed calls.

You can erase the missed call indicator either by reviewing the call log one by

one, or by pressing and holding CLEAR on the handset or CANCEL on the

telephone base in idle mode.

Review and dial a number in the call log

1. CID in idle mode -> q or p to scroll through the list.

2. While desired entry is displayed, press PHONE or /SPEA�ER on the cordless

handset, SPEA�ER on the telephone base, or lift the corded handset to call.

Answering system

About answering system and voicemail

Your telephone has separate indicators for two different types of voice messages:

those left on the built-in answering system and those left at your telephone

service provider’s voicemail. To listen to messages recorded on the built-in

answering system, refer to the Message playback section on the next page; to

listen to voicemail, contact your telephone service provider for more information.

Turn answering system on/off

The answering system must be turned on to answer calls and record messages.

Using a cordless handset:

1. MENU.

2. q or p --> Answering sys --> SELECT.

3. q or p --> Answer ON/OFF --> SELECT.

4. q or p --> On or Off --> SELECT.

When the answering system is on, the handset shows ANS ON.

Using the telephone base:

Press /ANSWER ON to turn the answering system on or off. If the

answering system is turned on, it announces, “Calls will be answered.” If the

answering system is turned off, it announces, “Calls will not be answered.”

•

Message alert tone

When this feature is on, and there is at least one new message, the telephone

base beeps every 10 seconds.

Using a cordless handset or the telephone base:

1. MENU -> q or p -> Answering sys -> SELECT.

2. q or p -> Ans sys setup -> SELECT.

3. q or p -> Msg alert tone -> SELECT.

4. q or p -> On or Off -> SELECT.

Call screening

Use this feature to choose whether incoming messages can be heard over the

telephone base when they are being recorded. If you turn call screening on, you

hear the incoming message. While monitoring an incoming message, you can

answer the call by pressing PHONE or /SPEA�ERSPEA�ER on a cordless handset,

lifting the corded handset or pressing SPEA�ER on the telephone base.

Using a cordless handset or the telephone base:

1. MENU -> q or p -> Answering sys -> SELECT.

2. q or p -> Ans sys setup -> SELECT.

3. SELECT to select Call screening.

4. q or p -> choose On or Off -> SELECT.

For more detailed instructions, please refer to the Abridged user’s manual

provided in your package, or for a full set of installation and operation

instructions, refer to the online CL84100/CL84200/CL84250/CL84300/CL84350

DECT 6.0 corded/cordless telephone/answering system with caller ID/call

waiting Complete user’s manual at www.telephones.att.com/manuals.

For customer service or product information, visit our website at

www.telephones.att.com or call 1 (800) 222-3111. In Canada, dial

1 (866) 288-4268.

AT&T and the AT&T logo are trademarks of AT&T Intellectual Property licensed to

Advanced American Telephones, San Antonio, TX 78219.

Printed in China. Issue 5 AT&T 12/11.