585-300-118 Issue 1 September, 1995 Table of Contents DEFINITY AUDIX System Release 3.
Blank Page
Contents About This Document 1 ■ Overview ix ■ Intended Audiences ix ■ Prerequisite Skills and Knowledge ix ■ Organization of This Document x ■ How to Use This Document x ■ Conventions Used in This Document xi ■ Trademarks and Service Marks xii ■ Related Resources xii ■ How to Get Help xii ■ How to Make Comments About This Document xiii Prerequisites 1-1 Display Set and Control-Link Integration 1-2 ■ Task 1: Verify the Selected Site 1-2 ■ Task 2: Gather Required Tool
Contents ■ ■ 3 2-10 Reserved RS-232 Connection 2-12 MFB Port Usage for DS and CL Integration 2-12 Task 7: Install the Terminals 2-12 Task 7A: Install a Terminal via a Direct Connection 2-13 Task 7B: Install a Terminal via Modems 2-16 Task 7C: Install a Terminal via ADUs 2-18 Task 7D: Install a Terminal via 7400A Data Sets 2-20 Task 8: Install the Control-Link Cable 2-22 Connect to the PI without an IDI 2-23 Connect to the PI with an IDI 2-24 Connect to the Digital Line Interface (TN
Contents ■ 4 Task 14: Perform Initial DEFINITY AUDIX Administration 3-11 Task 14A: Set the DEFINITY AUDIX Clock 3-12 Task 14B: Assign the DEFINITY AUDIX Machine Parameters 3-13 Task 14C: Run the Switch Translations Audit 3-14 Task 14D: Administer Voice Ports 3-15 Task 14E: Set Switch-Link Parameters 3-16 Set Switch-Link Parameters for CL Integration Set Switch-Link Parameters for DS Integration 3-16 3-18 Task 14F: Synchronize DEFINITY AUDIX System and Switch Clocks 3-20 Task 14G: Set Syst
Contents ■ Task 22: Test the Call Answer and Voice Mail Features DCS Subscribers 5 7 Task 23: Run Test Tape Long 4-13 ■ Task 24: Test Local Area Network 4-15 ■ Task 25: Clear Administration, Error, and Alarm Logs 4-16 Initial Subscriber Administration 5-1 ■ Initial Subscriber Administration Tasks 5-1 ■ Worksheets Needed 5-2 ■ Task 26: Ad d the Initial Subscribers 5-2 ■ Task 27: Switch Names Audit (for DS integration Only) 5-4 Task 28: Complete Initial Administration 5-4 Customer
Contents ■ Hardware Upgrades 7-9 Circuit Card Replacement 7-10 Control Link Upgrade 7-14 ■ Software Upgrade 7-14 ■ After the Upgrade 7-22 Installing, Administering, and Testing Intuity Message Manager A Announcement Set Considerations and Installation ■ ■ B A-1 Customized Announcement and Fragment Considerations A-1 Customer Modified Announcements A-2 Customer Modified and Added Fragments A-2 Announcement Set Identifiers A-2 Installing Ad ditional Language Sets A-3 Option Setti
Contents Jumper Setting Paradyne DataPort Express Modem Option Settings B-15 Paradyne COMSPHERE 3820 Modem Option Settings B-15 Paradyne COMSPHERE 3830 Modem Option Settings B-15 DM424 Modem Option Settings B-16 DM224 Modem Option Settings B-16 212AR Modem Option Settings B-16 2212D Modem Option Settings B-17 MPDM Data Module Option Settings B-17 DS Integration CL Integration C B-14 B-17 B-18 7400A Data Module Settings B-18 7400B Data Module Settings B-19 PEC Explosions C-1 ■ Com
About This Document Overview This document describes the installation, initial administration, and acceptance testing procedures for the hardware and software comprising the DEFINITY® AUDIX® Voice Messaging System release 3, version 2 (R3.2). Furthermore, this document describes the procedures used to update a system from a previous release to R3.2. The procedures are described in the form of specific tasks that should be completed in sequence.
About This Document Organization of This Document This document is organized as follows: ■ Chapter 1, ‘‘Prerequisites’’, identifies site requirements, required tools, safety considerations, and supported configurations. ■ Chapter 2, ‘‘Hardware Installation’’, describes all the tasks required for installing the DEFINITY AUDIX system hardware and the associated peripherals. ■ Chapter 3, ‘‘Initial System Administration’’, describes all the tasks required to initially administer the DEFINITY AUDIX system.
Conventions Used in This Document Conventions Used in This Document The following typographic conventions are used in this document: ■ Keyboard keys that you press are shown in rounded boxes. For example, an instruction to press the carriage return or equivalent key is shown in this document as: Press ■ RETURN . The word enter means to type a value or command and then press the RETURN key. For example, an instruction to type y and press RETURN is shown in this document as: Enter y to continue.
About This Document Trademarks and Service Marks The following trademarks are mentioned throughout this document: ■ AUDIX® is a registered trademark of AT&T. ■ DEFINITY® is a registered trademark of AT&T. ■ IntuityTM is a trademark of AT&T. Related Resources The following documents are related to DEFINITY AUDIX system installation and upgrades. ■ For all DEFINITY AUDIX system planning information, including the worksheets needed for installation, see Planning for DEFINITY AUDIX System, 585-300-601.
How to Make Comments About This Document How to Make Comments About This Document The reader comment card is located after the title page. While we have tried to make this document fit your needs, we are interested in your suggestions for improving it and urge you to fill one out.
About This Document xiv Issue 1 September 1995
Prerequisites 1 This chapter describes prerequisites for installing a DEFINITY AUDIX system. These include: Task 1: Verify the selected site Task 2: Gather required tools Task 3: Review safety considerations Task 4: Verify components and connectivity. Before beginning the installation, make sure you have completed these prerequisites. NOTE: If this Installation or Upgrade includes Digital Networking, ensure that the Installation Specification is available and filled out.
Prerequisites Display Set and Control-Link Integration The DEFINITY AUDIX system can be connected to the switch in one of two ways: display-set (DS) or control-link (CL) integration. CL integration requires an external connection from the switch to an RS-232C port on the multifunction board (MFB) of the DEFINITY AUDIX system. DS integration uses a channel (internal to the switch) that would otherwise be used to transfer display-set information.
Task 2: Gather Required Tools Task 2: Gather Required Tools To install an DEFINITY AUDIX system, you must have the following tools: ■ No. 1 or No. 2 Phillips screwdriver ■ Narrow width, flat blade screwdriver ■ 1/4-inch nut driver (recommended) ■ Antistatic grounded wrist strap Task 3: Review Safety Considerations ! WARNING: Electronic equipment can be damaged by electrostatic discharge. Do not touch any electronic component unless you are properly grounded.
Prerequisites Task 4: Verify the Components and Connectivity Review the connectivity diagrams in Figure 1-1: DEFINITY AUDIX System Connectivity Diagram — CL Integration, Figure 1-2: DEFINITY AUDIX System Connectivity Diagram — DS Integration, and Figure 1-3: DEFINITY AUDIX LAN Connectivity, on the following pages to gain a general understanding of how the DEFINITY AUDIX system is to be connected. In these drawings various optional connection methods are shown in coupling brackets.
Task 4: Verify the Components and Connectivity SWITCH ALARM BOARD ALB CABLE TO CROSS-CONNECT FIELD (X-C) LAN Most Switches† Except G3r RS-232 TO NON-US MODEM SYNCHRONOUS NULL MODEM CABLE TN765 Processor Interface IDI All Switches Except G3r MPDM X-C TN754 Digital Line Interface 110 V TN765 Processor Interface PORT B G3r ONLY MPDM X-C TN754 Digital Line Interface 110 V * MULTIFUNCTION BOARD MFB Y CABLE X-C MPDM TN754 110 V TN577 Packet Gateway IDI DSU 110 V X-C DSU 110 V PORT A
Prerequisites SWITCH ALARM BOARD TO CROSS-CONNECT FIELD ALB CABLE LAN RS-232 to non-US modem OPTIONAL PRINTER NULL MODEM MODEM PORT B Z3A4 T/R MODEM HOUSE WIRING Z3A1 ADAPTER 7400A MULTIFUNCTION BOARD MFB Y CABLE POWER SUPPLY PORT A Figure 1-2.
Task 4: Verify the Components and Connectivity DEFINITY AUDIX MFB D8W 104A* Customer Provided 10BaseT Twisted Pair (See Below Examples) ALB Intuity MESSAGE MANAGER CLIENT SOFTWARE** 10BaseT (TWISTED PAIR) BALUN ETHERNET COAXIAL CABLE DISK TAPE LAN SERVER *Demarcation Point —Provided by AT&T —RJ45 connection on a 104A connecting block, using a D8W modular wall cord —Located on cross-connect field —Maximum distance - 25 feet from switch ** Software —Installed by customer or AT&T —Maintained by AT&
Prerequisites 1-8 Issue 1 September 1995
Hardware Installation 2 This chapter describes the tasks needed to install the DEFINITY AUDIX system hardware and peripheral hardware. You can install the DEFINITY AUDIX system in any of the following switches. ■ System 75 R1V3 ■ DEFINITY Communications System Generic 1 (G1) ■ DEFINITY Communications System Generic 3 (G3i, G3s, G3vs,and G3r: all versions of all switches) Hardware Installation Tasks The DEFINITY AUDIX system installation tasks are virtually the same for all switch types.
Hardware Installation Worksheets Needed Before beginning these tasks, make sure you have the following worksheets from Planning for the DEFINITY AUDIX System, 585-300-601. ■ A-1, Port Slot Assignments (Before Carrier Rearrangement) ■ A-2, Port Slot Assignments (For Carrier Rearrangement) ■ A-3, Port Slot Locations for the DEFINITY AUDIX System Assembly ■ A-4, Control Link Cable-Connection Configuration ■ E-1, Terminals The Project Manager should have provided you with these worksheets.
Task 5: Install the DEFINITY AUDIX System Assembly I2C bus cable SCSI bus cable Power cable Tie wrap Multifunction board (TN566B) Alarm board (TN2170) Retaining pins Tape drive (without cover) Disk drive SCSI bus cable Power supply Figure 2-1.
Hardware Installation Slot and Carrier Restrictions If rearrangement of circuit packs in the PBX is required to accommodate the DEFINITY AUDIX system assembly, rearrange the packs as indicated on Worksheet A-2, Port Slot Assignments, before proceeding. If you are installing the DEFINITY AUDIX system in a System 75 XE or in a single-carrier cabinet of a DEFINITY G1, G3i, G3r or G3s, slots 14 (or slots 13 in an EPN control cabinet) should not be used for the DEFINITY AUDIX system assembly.
Task 5: Install the DEFINITY AUDIX System Assembly EXAMPLE OF DEFINITY AUDIX SLOTS 20 19 18 17 16 15 14 13 12 5th 4th 3rd 2nd 1st 11 10 9 8 7 MFB Y-CABLE (H600-352-G1) 6 5 4 3 2 1 ALB CABLE (H600-353 G2) AMPHENOL CONNECTOR FEMALE RS-232 Figure 2-2. FEMALE RS-232 FEMALE RS-232 FEMALE RJ45 Connecting the Adaptor Cables Rear-Panel View If the DEFINITY AUDIX system was shipped in a new switch, skip to Step 7 of this task.
Hardware Installation 3. Referring to Figure 2-1 and Steps 3a and 3b below, connect the DEFINITY AUDIX system assembly adaptor cables to the port connectors on the back of the switch. NOTE: You must connect these adaptor cables directly to the port connectors on the switch. If you install another cable between the switch and the cables, the DEFINITY AUDIX system will not operate correctly (either now or in the future). a.
Task 5: Install the DEFINITY AUDIX System Assembly or reinsert the assembly after the first attempt to insert it; make sure that the assembly is properly aligned in the slot, then insert it with a single firm push. 6. Insert the assembly and lock it in place by pushing up the securing latches on the two circuit packs. (It is normal for the two circuit packs to feel loosely connected to each other. This is to allow some give when you are seating them into the two slots of the backplane.
Hardware Installation The following list describes the positions of the LCD. ■ Standing to the right of the faceplate and reading from bottom to top, the first position contains the DEFINITY AUDIX system heartbeat. ■ The second and third positions display two letters indicating the following types of alarms: warnings (WN), minor (MN) and major (MJ). These positions are blank if there are no alarms. ■ The remaining positions indicate the DEFINITY AUDIX system states or menu selections.
Task 6: Connect the Alarm Board Cable Task 6: Connect the Alarm Board Cable The Alarm Board cable has three connectors available for outside connections: ■ Alarm Origination/Remote Maintenance Access ■ Local Area Network (LAN) used for Intuity Message Manager (IMM) ■ Reserved Refer to Figure 2-4, Alarm Board Cable Connections, to connect the cables : SWITCH ALARM BOARD ALB CABLE TO CROSSCONNECT FIELD I/O GROUP 300 CABLE RJ45 TO LOCAL AREA NETWORK RS-232 (RESERVED) MULTIFUNCTION BOARD MFB Y CAB
Hardware Installation DEFINITY AUDIX Connection 1. Connect the DEFINITY AUDIX system ALB cable to the cross-connect field. Attach the male amphenol connector on a Group 300 cable (on an existing switch, the one that you disconnected from the third DEFINITY AUDIX system slot in the previous task) to the female amphenol connector labeled ALARM on the ALB cable (the cable that is now connected to the third DEFINITY AUDIX system slot).
Task 6: Connect the Alarm Board Cable . 8AAAA AAAAAA AA 7AAAAAA AA 6AAAA AAAA AAAAAA AA 5AAAAAA 4AAAA AAAAAA AA 3AAAAAA AA 2AAAA AAAA AAAAAA AA AAAA 1 AA 104A AAAA AAAAAAA AAA8 AAAAAAA 7 AAAAAA6 AAAA AAAAAA AA AAAAAA 5 AAAAAA AAAA AAAAAA AA4 AAAAAA 3 AAAA AA AAAAAA2 AAAAAA 1 WE RJ45 Connectors To DEFINITY AUDIX Alarm Board LAN Connector AT&T Provided D8W Cord Figure 2-5. 10BaseT LAN Connection Customer Provided Connection 104A Connecting Block 3.
Hardware Installation Reserved RS-232 Connection Do not connect the RS-232 connector on the ALB cable In the U.S. The standard alarm origination circuit uses an on-board DEFINITY AUDIX system modem that is internally wired to the amphenol connector on the ALB cable. The RS-232 connector on the cable is used in installations outside of the U.S. MFB Port Usage for DS and CL Integration The Multifunction Board (MFB) Y-cable has two RS-232C connectors labeled Port A and Port B.
Task 7: Install the Terminals The terminals can be connected to Ports A and B in one of four ways: ■ Via a direct connection ■ Via modems ■ Via asynchronous data units (ADU) ■ Via 7400A data sets The connectivity for all supported terminals is similar. Therefore, the subtasks for this task are the same for all supported terminals, with differences identified as required for different terminal types.
Hardware Installation SWITCH ALARM BOARD ALB CABLE PORT B MULTIFUNCTION BOARD MFB Y CABLE *SEE NOTE GROUP 311 CABLE PORT A NULL MODEM *NULL MODEM NOT REQUIRED WHEN CONNECTING TO 715 BCT DCE PORT. Figure 2-6. Installing a Terminal via Direct Connection DC SWITCH ONLY MULTIFUNCTION BOARD PORT B MFB Y-CABLE DTE CONNECTION NULL MODEM 116-A OPTOISOLATOR DCE PORT A 116-A OPTOISOLATOR DCE 2-14 DTE DTE DCE CONNECTION NULL MODEM Figure 2-7.
Task 7: Install the Terminals 1. If you are installing a new terminal, unpack it according to the instructions supplied with the terminal. 2. Place the terminal on a suitable table within 15 feet of the switch cabinet if you have a 20-foot Group 311 cable, or within 45 feet if you have a 50-foot Group 311 cable, and connect the keyboard. 3. Connect a Group 311 cable between the DEFINITY AUDIX system MFB and the terminal: a.
Hardware Installation Task 7B: Install a Terminal via Modems This task describes how to connect a terminal via a modem to Port B (DP integtration only) of the MFB. (This task can also be used for remote connection to Port A, whether DS or CL integration.) To make sure the modems that you are installing are on the list of supported peripherals, refer to DEFINITY AUDIX System — System Description, 585-300-205. Refer to Figure 2-8, Connecting a Terminal to the MFB via a Modem, when performing this task.
Task 7: Install the Terminals c. Plug the modem power cord into a wall outlet and power on the modem. d. Set the modem options. Refer to Appendix B, ‘‘Option Settings’’, for a complete list of option settings for all supported modems. 3. Connect a modem to the terminal. a. If you are installing a new terminal, unpack it according to the instructions supplied with the terminal. b. Place the terminal on a suitable table and connect the keyboard. c.
Hardware Installation If the terminal does not display the login prompt when the DEFINITY AUDIX system is in one of the above states, try pressing the RETURN key a few times. If the login prompt still does not appear, write down the state displayed on the LCD then see the troubleshooting procedures for terminal connections in DEFINITY AUDIX System — Maintenance, 585-300-110. k. Log in to the DEFINITY AUDIX system (see Task 9 for login details).
Task 7: Install the Terminals 1. Connect the Z3A-4 ADU to the DEFINITY AUDIX system MFB. a. In the room where the switch and DEFINITY AUDIX system are located, attach one end of a Group 311 cable to the RS-232 connector labeled PORT B on the MFB Y-cable (the one connected to the fourth slot of the five DEFINITY AUDIX system slots). Attach the other end to the Z3A-4 (female) ADU. b. Plug the cable from the ADU into a telephone outlet. 2. In the terminal room, connect the Z3A-1 ADU to the terminal. a.
Hardware Installation If the terminal does not display the login prompt when the DEFINITY AUDIX system is in one of the above states, try pressing the RETURN key a few times. If the login prompt still does not appear, write down the state displayed on the LCD then see the troubleshooting procedures for terminal connections in DEFINITY AUDIX System — Maintenance, 585-300-110. 3. For CL integration, proceed to Task 8: Install the Control-Link Cable.
Task 7: Install the Terminals 1. Make sure the EIA connector board (located under the top panel) is set to DCE (the factory default). If not, unplug the card and turn it around to the DCE setting (see the 7400A Data Module User’s Manual, 555-020-706, for details). 2. Connect the 7400A data set to the DEFINITY AUDIX system MFB. a. In the room where the switch and DEFINITY AUDIX system are located, attach one end of a Group 311 cable to the RS-232 connector labeled PORT B on the MFB Y-cable.
Hardware Installation h. Set the terminal options. Refer to Appendix B, ‘‘Option Settings’’, for a complete list of option settings for all supported terminals. NOTE: When installing a serial printer on all but a 610 or 615 BCT, set the options on the printer as described in the manual supplied with the printer, then set the corresponding options on the terminal to match. On the 610/615, set the terminal options first, then set the printer options. i. At the terminal, enter AT.
Task 8: Install the Control-Link Cable Use Worksheet A-4 to determine which of the six cable-connection configurations to install. Then follow the steps in one of the following four subsections. In the steps in the following subsections, the equipment described is cross-referenced to the circled numbers in the figures. Connect to the PI without an IDI ! WARNING: Electric shock and/or fire may result from a cabinet-to-cabinet connection of the H600-406 control-link cable.
Hardware Installation Connect to the PI with an IDI Refer to Figure 2-12, Connecting the Control Link Cable to the PI with an IDI, when performing this task.
Task 8: Install the Control-Link Cable Connect to the Digital Line Interface (TN754) Refer to Figure 2-13, Connecting the Control Link Cable to a Digital-Line Interface, when performing this task. SWITCH DEFINITY AUDIX ALARM BOARD ALB CABLE 103A 3 PAIR 3 PORT B MULTIFUNCTION BOARD All Switches Except G3r 4 D8W-87 DEFINITY AUDIX X-C 5 H600-353, Grp 2 MFB Y CABLE 6 GROUP 311 CABLE TN754 MPDM 1 25 PAIR I/O 2 PI/TN765 110 V H600-352, Grp 1 PORT A Figure 2-13.
Hardware Installation Connect to the Packet G ateway Board (G3r only) Refer to Figure 2-14, Connecting the CL Cable to a Packet Gateway Board (G3r Only), when performing this task. SWITCH ALB CABLE DEFINITY AUDIX ALARM BOARD H600-353, Grp 2 G3r ONLY DEFINITY AUDIX MULTIFUNCTION BOARD H600-347, Grp 1 MFB Y CABLE PORT B H600-210, Grp n H600-405, Grp 1 1 TN577 PACKET GATEWAY IDI OUT 2 IN 3 H600-352, Grp 1 4 (USE ONE RS-232 CONNECTOR) PORT A Figure 2-14.
Task 8: Install the Control-Link Cable Connect to the TN577 via DSUs (G3r Only) Refer to Figure 2-15, Connecting the Control Link Cable to a TN577 via DSUs, when performing this task. SWITCH DEFINITY AUDIX ALARM BOARD ALB CABLE H600-353, Grp 2 3 PAIR 3 PAIR 103A 5 103A X-C H600-347, Grp 1 4 D8W-87 DEFINITY AUDIX MULTIFUNCTION BOARD MFB Y CABLE PORT Grp 311 B 1 G3r ONLY 7 6 M25A 2 110 V PORT A Figure 2-15.
Hardware Installation 8. Connect the other end of the M25A cable to one of the four RS-232 connectors on the H600-347 (labeled 7). 9. Attach the other end of the H600-347 cable to an RS-232C connector on the Packet Gateway board (TN577) on the G3r switch (labeled 8). 10. Proceed to Task 9: Install the Printer (Optional). Connect to the TN577 via MPDMs (G3r Only) Refer to Figure 2-16, Connecting the Control Link Cable to a TN577 via MPDMs, when performing this task.
Task 9: Install the Printer (Optional) 6. Attach a 25-pair cable between the cross-connect field and the digital line interface board (TN754) on the switch (labeled 6). 7. Attach a 25-pair cable between the cross-connect field and a second digital line interface board (TN754) on the switch (labeled 7). 8. Attach a 3-pair cord from the cross-connect field to the 103A adapter (labeled 8). 9. Attach one end of the D8W-87 modular cord to the 103A adapter (labeled 9). 10.
Hardware Installation 2. Connect the printer to the terminal. a. Connect one end of the printer cable to either the serial or parallel port on the terminal (depending on which type terminal and printer you are installing). Secure the connector with the captive screws. NOTE: If you are connecting a serial printer to the DTE connector on a 715 BCT, you must connect a null modem between the printer and the terminal. b. Connect the other end to the matching port (serial or parallel) on the printer. 3.
Task 10: Finalize and Test the Hardware The system responds with the Password prompt. b. Enter crftpw. The system responds with the Enter terminal type prompt. c. Enter one of the following: ■ 513 for a 513 BCT or 715 BCT; enter 513 also for a 610/615 BCT or a PC with a 513 emulation package. (Since 513 is the default, you can just press RETURN to select it). ■ 4410 for a 4410 or 5410 terminal; enter 4410 also for a 610/615 BCT or a PC with a 4410 emulation package.
Hardware Installation NOTE: The location field will initially display “1a01” for component types ALARM_BD, MFB_BD, DISK, and TAPE since they have not yet been administered. Ignore this field.
Task 10: Finalize and Test the Hardware 4. Check the alarm status. a. With the cursor on the DEFINITY AUDIX system command line, enter display alarms. The system displays the Display Alarms screen. b. Check the ALARM TYPES fields for any active alarms (indicated by a “y” next to the alarm type). Press ENTER (F3) to display the alarms. You should see a voice ports major alarm and possibly port warnings because the ports are not administered yet. These are the only alarms that you should expect. c.
Hardware Installation 6. Give the program tape and one of the blank cartridge tapes to the DEFINITY AUDIX system administrator, or put them in a safe place (away from electromagnetic parts). Keep the other blank tape, you will install it in the drive later (Task 14). 7. With the cursor on the command line, enter logoff to log off the terminal. 8. Proceed to the tasks in Chapter 3, ‘‘Initial System Administration’’.
Initial System Administration 3 This chapter describes the tasks required to initially administer the DEFINITY AUDIX System.
Initial System Administration Worksheets Needed Before beginning these tasks, make sure you have the following worksheets. NOTE: The project manager should have made arrangements for you to receive these worksheets from the Planning for the DEFINITY AUDIX System book, 585-300-601.
Windowing on the 715 Terminal Windowing on the 715 Terminal If you are using the 715 BCT terminal, you should be aware of its windowing capabilities. You can use the 715 terminal to log on to both the switch and the DEFINITY AUDIX system to perform administration tasks and easily toggle back and forth between the two sessions. The windowing functions are controlled by the four function keys, F1, F2, F3, and F8 as described in Table 3-1, Function Keys Used for Windowing on the 715 BCT. Table 3-1.
Initial System Administration Task 12: Activate Customer Options This task is required for all installation scenarios to check if customer options have been activated and set to their limits. Use Worksheet C-1, Activate Customer Options, when completing this screen. Activating customer options is normally done before the system is shipped.
Task 12: Activate Customer Options The system displays the System-Parameters Customer-Options screen. NOTE: The DEFINITY AUDIX Status line will display an M (and possibly other alarms) in the alarms field reflecting the voice ports alarm that you saw on the Alarm Report screen in Task 10. These alarms should resolve themselves when you administer the voice ports (in Task 14D) and can be ignored at this time.
Initial System Administration If the value in any of these fields needs to be changed, proceed to the next section of this task to change the customer options. Change Customer Options NOTE: You must use the init login to change the System-Parameters CustomerOptions screen. If this password is not available to you, contact the Remote Support Center to have the customer options changed. Complete the following steps only if the customer options need to be changed or activated. 1.
Task 13: Activate DEFINITY AUDIX Server Hardware Options 10. Move the cursor to the Multilingual? field. This indicates whether or not multilingual announcement sets can be administered on a per subscriber or class-of-service basis. The default value is n. Type y to enable the Multilingual feature. 11. Move the cursor to the Maximum Number of IMAPI Sessions: field and, using the information on the customer’s order, type 32, the allowable number of sessions. 12.
Initial System Administration Task 13A: Set System Parameters for Intuity Message Manager 1. With the cursor on the DEFINITY AUDIX command line, type change system-parameters IMAPI-options and press RETURN . The system displays the System-Parameters Imapi-Options screen. 2. Move the cursor to the Maximum Number of ENABLED IMAPI Sessions field. This should be 32. 3. Move the cursor to the Enable Check New Messages field. Set to y.
Task 13: Activate DEFINITY AUDIX Server Hardware Options 7. Move the cursor to the LAN IP Address field. This is the number assigned to the AUDIX server by the LAN administrator. The site-specific address is expressed as nnn.nnn.nnn.nnn, each nnn representing a decimal integer between 1 and 126, or 128 and 254. 8. Move the cursor to the LAN Subnet Mask field. Part of this number matches the network IP ad dress, while the remaining part contains the host interface address. (Usually, 255.255.255.0 will work.
Initial System Administration The system displays the Class of Service screen. 2. Ensure that the IMAPI access? field for Intuity Message Manager and the IMAPI Voice File Transfer? field for a personal folder are set to y. 3. With the cursor on the DEFINITY AUDIX command line, type change subscriber followed by the extension of a subscriber who is to have Intuity Message Manager on their PC. Press RETURN . Press NEXTPAGE (F7) to display second thepage.
Task 14: Perform Initial DEFINITY AUDIX Administration The system displays the Change Subscriber screen. 4. Ensure that the IMAPI access? field for Intuity Message Manager and the IMAPI Voice File Transfer? field for a personal folder are set to y. 5. Proceed to the following task. Task 14: Perform Initial DEFINITY AUDIX Administration This task is required for all installation scenarios. There are 13 parts to this task. a. Set the DEFINITY AUDIX clock b. Assign the DEFINITY AUDIX machine parameters c.
Initial System Administration i. Assign the time zone j. Reboot the system k. Run the switch-names audit (only applies to DS-integrated systems) l. Check alarm status m. Check hardware status Task 14A: Set the DEFINITY AUDIX Clock 1. At the login prompt, enter craft. The system displays the Password prompt. 2. Enter crftpw. The system displays the Enter terminal type prompt. 3.
Task 14: Perform Initial DEFINITY AUDIX Administration The system displays the Date and Time screen. 5. Move the cursor to the month field and type the name (not the number) of the current month. 6. Move the cursor to the Day of the Month field and type the two digits of the current day of the month (not the day of the week). For example, type 11 if the current date is April 11. 7. Move the cursor to the Year field and type the full four digits of the current year. 8.
Initial System Administration The system displays the Machine Profile screen. 2. Move the cursor to the Machine Name field and type the new name to be assigned to this DEFINITY AUDIX system. The machine name must be from 1 to 8 characters in length. 3. Verify that the Machine Type field displays audix. If not, move the cursor to that field and type audix. 4. Move the cursor to the Extension Length field and type the number of digits that the extensions on this DEFINITY AUDIX system will have. 5.
Task 14: Perform Initial DEFINITY AUDIX Administration This audit takes about 1-2 seconds. Run the audit as described below. 1. With the cursor on the DEFINITY AUDIX command line, type audit switch-translations and press RETURN . The system displays the Audit Results screen. 2. Press the ENTER (F3) function key to begin the audit. 3. When the audit is complete (in a few seconds) proceed to Task 14D: Administer Voice Ports.
Initial System Administration The system displays the Voice Group screen. 2. With the cursor at the Port field, type the location identifier of the first port. (A seven-character identifier is shown on the illustration.) For example, if the DEFINITY AUDIX system multifunction board (MFB) is in module 1, carrier A, slot 2, the first port location is 01A0201 (the last two digits in this example are the port number). 3. Move the cursor to the Extension field and type the extension number of the first port.
Task 14: Perform Initial DEFINITY AUDIX Administration If the system will be using CL integration, perform the following steps. 1. With the cursor on the DEFINITY AUDIX command line, type change switch-link and press RETURN . The system displays the Switch-Link DCIU-SCI screen. 0 2. Enter values for the Host Switch and AUDIX fields from Worksheet C-3 Assign the DEFINITY AUDIX Machine ID. The number entered in the Host Switch field must match the Local PBX ID administered on the switch.
Initial System Administration The Logical Channel, Switch Port, and AUDIX numbers must be the same as the corresponding numbers administered on the switch. These fields have different names on the switch screens. The field names on the switch screens corresponding to the DEFINITY AUDIX Switch Link screen field names are shown in the following table: Table 3-2. Field-Name Correspondence — DEFINITY AUDIX System vs.
Task 14: Perform Initial DEFINITY AUDIX Administration Perform the following steps: 1. Enter in the Host Switch field the switch number assigned to the switch into which the AUDIX system is installed. 2. Enter in the AUDIX field the machine number of the AUDIX system being installed. 3. Enter in the Call Answer Timeout field the number of seconds the system shall wait for touch-tone digits when it answers a call without receiving a “connect” message.
Initial System Administration Task 14F: Synchronize DEFINITY AUDIX System and Switch Clocks This task is required for all installation scenarios. NOTE: The switch clock may not be set at this time. If it is not, set the switch clock before performing this task. (See the appropriate switch document for the procedure to set the switch clock.) 1. With the cursor on the DEFINITY AUDIX command line, type set time and press RETURN . The system displays the Date And Time screen. 2.
Task 14: Perform Initial DEFINITY AUDIX Administration Task 14G: Set System Parameters Limits This task is required only if the customer wants to use subscriber limits that are different from the defaults. Check Worksheet C-4, Set System Parameters Limits, to see if you need to change the system parameters limits. If not, skip to Task 14H: Run the Switch Translations Audit a Second Time. If changes are indicated on the worksheet, perform the following steps. 1.
Initial System Administration Task 14H: Run the Switch Translations Audit a Second Time This task is required for all installation scenarios. You must run the Switch Translations audit a second time to update the DEFINITY AUDIX system processes again with the new information you have administered. 1. With the cursor on the DEFINITY AUDIX command line, type audit switch-translations and press RETURN . The system displays the Audit Results screen. 2. Press the ENTER (F3) function key to begin the audit.
Task 14: Perform Initial DEFINITY AUDIX Administration 1. With the cursor on the DEFINITY AUDIX command line, type change switch-time-zone and press RETURN . The system responds with the Switch Time Zone screen. If the time zones of your associated switches have not been defined for your AUDIX system, only the columns of switch numbers will appear. Fill in the table for those switches that are part of your DEFINITY communications system network. 2.
Initial System Administration Task 14J: Reboot the DEFINITY AUDIX System This task is required for all installation scenarios. 1. With the cursor on the DEFINITY AUDIX command line, type reset system reboot and press RETURN . The system displays the Reset System Reboot screen. 2. Press the ENTER (F3) function key to begin the reboot.
Task 14: Perform Initial DEFINITY AUDIX Administration Subtask 14K: Run the Switch Names Audit This task is required only if the system uses DS integration. Otherwise, skip to Task 14L: Check Alarm Status. The Switch Names audit uploads the names-to-extensions database from the switch. The Switch Names audit could take from 5 minutes to an hour, depending on the size of the database. 1. With the cursor on the DEFINITY AUDIX command line, type audit switch-names and press RETURN .
Initial System Administration Task 14L: Check Alarm Status This task is required for all installation scenarios. 1. With the cursor on the DEFINITY AUDIX command line, type display alarms and press RETURN . The system displays the Alarm Report screen. 2. Check the ALARM TYPES fields for any active alarms — make sure that a “y” (the default) appears in each of the alarm type fields and press ENTER (F3) to display the active alarms. 3.
Task 14: Perform Initial DEFINITY AUDIX Administration The system displays the List Configuration screen. 2. Make sure the screen displays the following components (indicating that the system correctly recognizes all the components). ■ ALARM_BD ■ ABP_FW ■ MFB_BD ■ FAC_FW ■ 386_FW ■ DISK ■ TAPE 3. If all the components are listed and shown in the proper location, skip to Step 4. Otherwise, see DEFINITY AUDIX System — Maintenance, 585-300-110, for troubleshooting procedures. 4.
Initial System Administration The system displays the Voice Group Status screen. 5. Make sure all the ports that are sup posed to be active are shown on the screen with the correct location and extension and that the State field shows ISI (In-Service Idle). 6. If any of the port information is incorrect, see DEFINITY AUDIX System — Maintenance book, 585-300-110 for complete troubleshooting procedures. Step 7 is required only if the DEFINITY AUDIX system will use CL integration. If not, skip to step 8. 7.
Task 15: Activate Parameters and Basic Features Task 15: Activate Parameters and Basic Features This task is required if the customer has indicated specific features to be activated. Check Worksheet C-6, Activate Parameters and Basic Features to see if any features are to be activated. If no features are to be activated, skip to Task 16: Ad d Tape. Otherwise, perform the following steps. 1. With the cursor on the DEFINITY AUDIX command line, type change system-parameters features and press RETURN .
Initial System Administration 3. Press the NEXTPAGE (F7) function key to display page two of this screen. 4. Move the cursor to any of the features to be activated on page 2 and enter the appropriate data as specified on the worksheet. 5. Press the 3-30 NEXTPAGE Issue 1 September 1995 (F7) function key to display page three of this screen.
Task 16: Add Tape 6. Move the cursor to any of the fields and add announcement sets or change rescheduling increments as needed. 7. When you have completed all the changes, press the key to save the changes. ENTER (F3) function If no covering extension is administered, the system displays the following message: Covering Extension not defined, press Enter to confirm. 8. Press the ENTER (F3) function key again. 9.
Initial System Administration Write Protect tab This side Arrow indicating direction to insert tape. Figure 3-1. Tape side down Tape Cartridge 5. Close the tape drive with the tape cartridge installed. 6. At the terminal, type add tape and press 3-32 Issue 1 September 1995 RETURN .
Task 16: Add Tape The system displays the Tape screen. 7. With the cursor on the Volume Name field, type backup. 8. Press the ENTER (F3) function key. The Message line displays the following message. This operation erases all existing tape data. Press "ENTER" to confirm. 9. Press the ENTER (F3) function key to begin the add tape function. It takes approximately 3 minutes to retention the tape if the cartridge is blank.
Initial System Administration Task 17: Check the Status of the Switch Names Audit This task is required if the system is using DS integration. Otherwise, skip to Chapter 4, ‘‘Acceptance Checks’’. The purpose of this task is to check the status of the switch names audit operation initiated in Subtask 14K: Run the Switch Names Audit. 1. With the cursor on the DEFINITY AUDIX command line, enter status audit and press RETURN .
Task 17: Check the Status of the Switch Names Audit The system responds with the Administration Log screen. Leave the Start Date, Time, and Type fields on page 1 blank to display all log entries. Press ENTER (F3) to display the administration-log entries on page 2 of the screen. 4. Check the log for entries that indicate the Switch Names audit found one or more non-unique subscriber names.
Initial System Administration 5. Inform the switch system administrator of any entries in the administration log and ask the administrator to change all non-unique subscriber names in the switch names database to unique names. NOTE: To find non-unique names using G3-MA screen, connect to the switch and use the data-management option from the main menu. Create a template by using the add data-template . Retrieve the data and sort it using the name as the key.
Acceptance Checks 4 This chapter describes tests to ensure that the DEFINITY AUDIX System is functioning properly after installation. Joint Acceptance Testing is used to ensure that IMAPI is operational. These tests should be run with a customer LAN system administrator. Joint Acceptance Testing is required to be executed by both the customer and the AT&T installer when the entire solution includes AT&T and customer-provided equipment.
Acceptance Checks Task 24: Test Local Area Network (optional) Task 25: Clear administration error log and alarm log, if necessary Worksheets Needed Before beginning these tasks, make sure you have the Administering Voice Ports as Stations Worksheet — B-1 for Display Set or B-5 for Control Link — from Planning for the DEFINITY AUDIX System, 585-300-601. The project manager should have provided you with this worksheet.
Task 18: Alarm Origination Administration/test and Status Tape The system displays the System-Parameters Maintenance screen With information given to you by the Project Manager and with the help of the INADS people, fill in all fields on the screen. 4.
Acceptance Checks 5. Press NEXTPAGE (F7) to display the second page of System-Parameters Maintenance screen. If Worksheet C-10 Set Up Alarm Origination, indicates that alarm origination is to be activated through the switch only, enter n in the Alarm Origination Active? field. If either audix only, or audix & switch, is indicated on Worksheet C-10, enter y in the Alarm Origination Active? field. 6. Ask the INADS personnel to login and display the System-Parameters Maintenance screen.
Task 18: Alarm Origination Administration/test and Status Tape 7. If all the fields are properly filled in, press the screen. CANCEL (F1) function key to exit the This completes the alarm origination and test. 8. Verify the status of the add-tape function performed in the previous task by typing status tape followed by RETURN . The system displays the Status Tape screen.. 9. The Status field should display In service, idle. If not, see DEFINITY AUDIX System — Maintenance, 585-300-110.
Acceptance Checks Task 19: Perform Dial Tone Test for DS Integrated Systems If the system is using DS integration, continue, If the system is using CL integration, skip this task. Use the information on Worksheet B-1, Administering the Voice Ports as Stations. 1. If you have not already done so, log in to the switch administration terminal. 2. In switch administration, with the cursor on the command line, enter display feature-access-codes. The system displays the Feature Access Codes screen. 3.
Task 20: Run Test Switch-Link Long 9. Press the ENTER (F3) function key to busy out the voice groups and exit the screen. 10. From any telephone, dial the priority calling access code that you wrote down in Step 4. 11. When you hear the second dial tone, enter the extension of the first DEFINITY AUDIX voice port listed on Worksheet B-1, Administering Voice Ports as Stations. If the DEFINITY AUDIX system answers, proceed to Step 12.
Acceptance Checks The system responds with the Switch-Link Test Results screen. 4. Press the ENTER (F3) function key to begin the test. The test takes from 2 to 5 minutes to complete. 5. When the test completes successfully, proceed to ‘‘Task 24: Test Local Area Network’’ on page 4-15. If the test does not complete, refer to DEFINITY AUDIX System —Maintenance, 585-300-110. 6. If running in a DCS network, the test results for each switch node will appear on the Switch-Link Test Results screen.
Task 21: Add Two Test Subscribers The system responds with the Subscriber screen. NOTE: The two test subscriber extensions used in this task must be administered on the switch. The second test extension must have the coverage path for the AUDIX set. You can administer subscribers on the switch using the Ad d Station screen. 3. With the cursor at the Name field, type the name of the first test subscriber (for example, test-1 or subscriber-1). 4.
Acceptance Checks 7. If running in a DCS environment, repeat Steps 2 through 5 for one test subscriber on each switch in the DCS network. NOTE: Make sure that each DCS remote subscriber is assigned the correct switch number. The switch number for DCS remote subscribers is not the same as the host switch number. The Switch Number field on the Subscriber screen must match the switch number for the subscriber’s switch on the Switch Link DCIU-SCI screen (see Task 14E). 8.
Task 22: Test the Call Answer and Voice Mail Features f. Press 2 then press 0 to listen to the message you recorded from the first test extension. g. After listening to the message, press * D to delete the message. 3. Create a test Voice Mail message. a. From the DEFINITY AUDIX session you are currently in, press 1 . b. After the tone, speak a test message (for example “This is a test Voice Mail message.”) c. When you have finished speaking the message, press approve the message. # to d.
Acceptance Checks c. After the system greeting and the tone, leave a test message (for example, “This is a test Call Answer message.”) d. Hang up. 2. Retrieve the Call Answer message. a. If you are in contact with someone at the remote site, ask them to check the MWI — either a lamp on the phone or a stutter dial tone — on the remote subscriber’s phone. (The MWI signal may take up to 1 minute to appear.) If it is on, proceed to the next step.
Task 23: Run Test Tape Long 4. Retrieve the test Voice Mail message. a. If you are in contact with someone at the remote site, ask them to check the MWI — either a lamp on the phone or a stutter dial tone — on the remote test subscriber’s phone. (The MWI signal may take up to one minute to appear.) If it is on, proceed to the next step. Otherwise, refer to the troubleshooting procedures in DEFINITY AUDIX System—Maintenance, 585-300-110. b. Call the remote DEFINITY AUDIX extension to retrieve the message.
Acceptance Checks The system responds with the Tape Test Results screen. 3. Press the ENTER (F3) function key to begin the test. The test takes from 3 to 5 minutes to complete. If it does not complete successfully, refer to DEFINITY AUDIX System — Maintenance, 585-300-110.
Task 24: Test Local Area Network Task 24: Test Local Area Network If possible, Task 24: Test Local Area Network and Task 25: Clear Administration, Error, and Alarm Logs are done jointly with the customer’s LAN system administrator. Prior to activating and installing the LAN options that will allow Intuity Message Manager to work, the LAN administrator must do one of the following: — Add the AUDIX host name to the network domain name server.
Acceptance Checks 2. Press the ENTER (F3) function key to begin the test. The test takes up to 2½ minutes to run. 3. If any of the individual tests fail or abort, refer to DEFINITY AUDIX System — Maintenance, 585-300-110. If there are problems with the network itself, the LAN system administrator will have to resolve these problems before proceeding with this test. 4.
Initial Subscriber Administration 5 This chapter describes the tasks to administer the initial subscribers. Initial Subscriber Administration Tasks This chapter contains the following task: Task 26: Add the initial subscribers Task 27: Run the switch names audit (Display Set only) Task 28: Complete initial administration Task 26 should be completed by the DEFINITY AUDIX system administrator or, if the task is included as part of the signed contract, by the AT&T Software Specialist (SS).
Initial Subscriber Administration Worksheets Needed Before beginning these tasks, make sure you have worksheet C-8, Ad d Subscribers, from Planning for the DEFINITY AUDIX System, 585-300-601. The Project Manager or Software Specialist should have provided this worksheet. Task 26: Add the Initial Subscribers This task is required for all installation scenarios. This task describes the basic procedure for adding subscribers via the Subscriber screen.
Task 26: Add the Initial Subscribers The system responds with the Subscriber screen. 2. With the cursor at the Name field, type the name of the first subscriber listed on Worksheet C-8. 3. Move the cursor to the Extension field and type the extension of the first subscriber. 4. Press the ENTER (F3) function key to add the subscriber. 5. Repeat steps 1 through 4 for each subscriber listed on the Ad ding Subscribers worksheet. 6.
Initial Subscriber Administration Task 27: Switch Names Audit (for DS integration Only) This task is required only if the DEFINITY AUDIX system will be running in DS integration. 1. Execute the audit switch-names command as described in Subtask 14K (Run the Switch Names Audit), in Chapter 3, ‘‘Initial System Administration’’ 2.
Customer Acceptance 6 Project Management Tasks: This chapter lists the tasks that the Project Manager must perform with the customer to hand the DEFINITY AUDIX system over to the customer. Most of these tasks are part of the Streamlined Implementation process. Therefore, they are not described in this document but are listed here as a final check to make sure they are completed.
Customer Acceptance ■ Verify that all DEFINITY AUDIX system documentation is present, and then instruct the customer regarding how to use the documentation set (which documents are used when). ■ Provide the customer with a list of phone numbers and post-cut escalation points. Task 31: Demonstrate Updated Customer Database Show the customer the Test Alarm-Origination Short screen to verify that the customer database is updated. Task 32: Project Review.
Upgrades to R3.2 7 This chapter describes how to upgrade from previous releases of the DEFINITY AUDIX system to R3.2. Upgrade Overview The DEFINITY AUDIX 3.2 system differs from earlier releases of the system in ways that significantly affect the tasks you must perform in an upgrade. Hardware Hardware changes that affect upgrades follow:: Disk Drive The DEFINITY AUDIX 3.2 system offers an optional 1.05- GB disk drive that allows up to 100 hours of voice storage.
Upgrades to R3.2 Analog and Digital Port Emulations To work with the switch, the DEFINITY AUDIX 3.2 system can emulate these port boards: ■ TN746 analog port emulation, which allows up to 16 voice ports. ■ TN754 digital port emulation, which allows up to 8 voice ports. ■ TN2181 digital port emulation, which allows up to 16 voice ports. (Not available with System 75, G1, and G3V1 switches.
Up grade Worksheet Upgrade Worksheet The information in the following worksheet determines what upgrade tasks are necessary. If you do not already have this information, use the worksheet to compile it.. Features/Capacities Old System New System 1. DEFINITY AUDIX Release (1.0, 2.0, 3.0, 3.1) __________________ 3.2 2. Switch Type (Sys. 75, G1, G3V1 prior to Iss. 16.2, G3V1 Iss. 16.2 or greater, G3V2, G3V3, G3V4) __________________ __________________ 3.
Upgrades to R3.2 . Features/Capacities Old System New System 15. Message Manager IP address Subnet mask Gateway Address __________________ __________________ __________________ __________________ __________________ __________________ 16. Alarm Board (2169/2170) __________________ __________________ 17.
Upgrade Checklist Upgrade Checklist The following checklist lists, in recommended order, the upgrade tasks you may need to perform. Use the information in the Upgrade Worksheet to determine which tasks are necessary. Task Comments Where Task is Described 1. Upgrade the Disk Drive, if Necessary Necessary if the new system needs greater than 40 hours of speech or the old system has a 6-hr. disk. The inclusion of digital networking may also add significant storage needs.
Upgrades to R3.2 Task 6. Add control link cable, if necessary. Comments Where Task is Described Necessary if old system is DP integration and new system is CL integration. Chapter 2, Task 8: Install the Control-Link Cable. 7. Continue with step 7 of software upgrade and complete software upgrade. This chapter in section, Software Upgrade. 8. Change switch integration, if necessary.
Upgrade Checklist Task Comments Where Task is Described Necessary if the customer wants digital networking, but also wants the features supported by CL integration (such as DCS, enhanced call transfer, and leave word calling). Appendix A in Switch Administration for the DEFINITY AUDIX System (585-300-509) Necessary if System 75 or G1 switch and customer simply wants more ports and does not want digital networking.
Upgrades to R3.2 Changing from AMIS to Digital Networking In addition to normal administration to set up digital networking, change the machine type for each remote machine that changees from AMIS networking to digital networking. To change machine type, follow these steps: 1. Enter the command change machine macnine-name. The Machine Profile screen appears for the machine you named. 2.
Hardware Upgrades Hardware Upgrades To upgrade any DEFINITY AUDIX to R3.2, the following items are necessary at the upgrade site: ■ R3.2 generic software tape ■ Tape or tapes with purchased language sets ■ Two blank tapes, necessary to save customer data during the upgrade. These tapes will not be left at the upgrade site. ■ TN566B MFB Circuit Card (upgrading R1.0 or R2.0 with support of 10 voice ports or less) ■ TN567 MFB Circuit Card (upgrading an R1.0 or R2.
Upgrades to R3.2 Circuit Card Replacement ! WARNING: Static electricity can be destructive to system parts. Use an antistatic wrist strap whenever removing or installing a DEFINITY AUDIX system. Also use an antistatic mat when servicing the MFB and alarm circuit cards. Use this procedure if either, or both, the TN566B MFB and the TN2169 Alarm Board must be replaced. Step 1: Shut down the system in a camp-on manner using the Reset System Shutdown screen.
Hardware Upgrades I2C bus cable SCSI bus cable Power cable Tie wrap Multifunction board (TN566B) Alarm board (TN2170) Retaining pins Tape drive (without cover) Disk drive SCSI bus cable Power supply Figure 7-2.
Upgrades to R3.2 To remove the TN566 MFB and the TN2169 alarm board, perform these steps: 1. Unsnap the two gang latches at the bottom front of the MFB and alarm board, and swing downward. Squeeze the boards together and slip off the spring clip. ! CAUTION: Carefully slide the DEFINITY AUDIX system from the switch carrier. Handle with care. The system weighs 6.2 pounds, use both hands when removing the system. 2. Disconnect the interboard bus cable from the top edge of both boards using the pull tab. 3.
Hardware Upgrades To assemble the MFB and alarm board, perform these steps: 1. Place the two boards together and attach them using the three sockethead slotted screws. 2. Reconnect the interboard bus cable (H600-345) to the top edge of both boards. NOTE: The interboard bus cable connector with the pull tab connects to the MFB board. 3. Connect the tape drive SCSI bus cable (H600-344) to the tape drive. 4. Connect the tape drive SCSI bus cable to the alarm board. 5.
Upgrades to R3.2 Control Link Upgrade Refer to Chapter 2, Task 8: Install the Control-Link Cable, for installation procedures. Software Upgrade To upgrade an R1.0, R2.0, R3.0 or R3.1 DEFINITY AUDIX system to release R3.2, perform the following steps. If problems occur, contact the Technical Service Organization (TSO). The approximate time to complete each step is shown in brackets [ ]. Times may vary widely, depending on the size of the system and the voice storage volume.
Software Upgrade 5. [5 min] Shut down the system in a camp-on manner using the RESET SYSTEM SHUTDOWN screen. The system responds with information similar to the following: System name: audix login: INIT: New run level: 0 The system is coming down. Please wait. System services are now being stopped. System data saved during shutdown. The system is down. Transferring to Firmware. ..... SHUTDOWN Pending, Code = F022 Software Maintenance Shutdown SHUTDOWN Completed 6.
Upgrades to R3.2 7. [1 min.] Invoke command mode by pressing CONTROL - C C . The system responds with information on the screen similar to what follows: MFB 386FW Version: AU00S3EC Local Console: Output ON, Input ON Remote Maintenance Console: INACTIVE command menu:? 8. Press SHIFT ? ENTER to list available commands. A menu similar to that below is displayed.
Software Upgrade Confirm that the board diagnostics passed. ! WARNING: In the next step do not press 1 (the Initialize Disk option), which would destroy all existing customer data. 14. [10 min] When the menu appears, enter 3 to select Copy Generic Partitions To Disk. The system responds with information on the screen similar to what follows: Enter option: 3 Enter SCSI ID of Disk (default 0): 15. Enter 0 (zero, the default) for the SCSI ID.
Upgrades to R3.2 Copyright (c) 1984, 1986, 1987, 1988, 1989, 1990, 1991 AT&T Copyright (c) 1987, 1988 Microsoft Corp. All Rights Reserved DEFINITY(R) AUDIX(R) System Copyright (c) 1991,1992,1993 AT&T All Rights Reserved. The system is coming up. Please wait. WARNING: Firmware verification/reprogramming in progress. Do not interrupt until completed. Firmware verification/reprogramming completed successfully. MFB state set to 35 Welcome to DEFINITY(R) AUDIX(R) System Release 3.
Software Upgrade 17. When the yellow tape LED on the tape drive goes out, press RETURN . The screen shows the progress of the backups as they are done. If asked to insert the second blank backup tape, insert it, and press RETURN . Write the volume label *** START Fri Jan 06 08:50:07 EST 1995 *** *** END Fri Jan 06 08:50:33 EST 1995 *** Save nightly *** START OF BACKUP Fri Jan 06 08:50:39 EST 1995 *** .............................................
Upgrades to R3.2 For others: Upgrading subscriber profile database to R3.2 ... completed. Upgrading message header database to R3.2.. completed. Upgrading voice count database to R3.2 ... completed. Upgrading mailbox database to R3.2 ...completed Upgrading mailing list database to R3.2 ...completed Upgrading traffic load day database to R3.2 ...completed Upgrading traffic load hour database to R3.2 ...completed Upgrading subscriber profile database to R3.2 ...completed Upgrading traffic database to R3.2 ..
Software Upgrade 20. Log in to the DEFINITY AUDIX system as craft. Wait for Active to appear on the status line before continuing. 21. [less than 1 min] Run TEST TAPE CLEAN to reset the tape cleaning interval counter. 22. [1 min] Check the Alarm Status at the top of the screen. If there are alarms, enter DISPLAY ALARMS at the command line and take the appropriate action to remove the alarms. Consult DEFINITY AUDIX System — Maintenance, 585-300-110 for information on removing alarms. 23.
Upgrades to R3.2 31. [5 min] Run SAVE WEEKLY. When the administration alarm, A, appears on the status line, run DISPLAY ADMINISTRATION-LOG. If the SAVE WEEKLY operation was successfully completed, save manual_weekly passed will be displayed. 32. Enable alarms by entering ENABLE ALARM-ORIGINATION. 33. If you do not have to install Intuity Message Manager, enter logoff to log off the system. If Intuity Message Manager is going to be installed, continue with the After the Upgrade section of this document.
After the Upgrade . AAAA AAAAAA AA8 AAAAAA 7 AAAA AAAAAA AA6 AAAAAA 5 AAAA AAAAAA AA4 AAAAAA 3 AAAA AAAAAA AA AAAAAA2 1 WE To DEFINITY AUDIX Alarm Board LAN Connector Figure 7-3. 8AAAA AAAAAA 7AAAAA 6AAAA AAAAAA 5AAAAA A 4AAAA AAAA AAAAAA AAAA 3 A A 2AAAA AAAAA 1 104A 10BaseT LAN Connection 104A Mounting Block 2. Mount the 104A connecting block on the wall field. 3. Connect the RJ45 10BaseT LAN connector into one of the connections at the bottom of the 104A connecting block. 4.
Upgrades to R3.2 6. Prior to activating and installing the LAN options that will allow Intuity Message Manager to work, the LAN administrator must do one of the following: — Add the AUDIX host name to the network domain name server — Create a host file on each PC, typically under the \net\tcp\hosts directory — Do neither of the above if using a numeric IP address 7. With the cursor on the DEFINITY AUDIX command line, enter display system-parameters customer options.
After the Upgrade The system displays the System-Parameters IMAPI-Options screen. The Maximum Number of ENABLED IMAPI Sessions field should be set to 32. 10. Set the Enable Check New Messages field to y. This allows clients to check for new messages without the overhead of logging in. If left at n, automatic new message notification from Intuity Message Manager is disabled. 11. Set the Enable Deliver CA Message field to n.
Upgrades to R3.2 14. Move the cursor to the LAN IP Ad dress field, and enter the number assigned to the AUDIX server by the LAN administrator. The site-specific address is expressed as nnn.nnn.nnn.nnn, each nnn representing a decimal integer between 1 and 126, or 128 and 254. 15. Move the cursor to the LAN Subnet Mask field, and enter the Subnet Mask for your network. The LAN administrator has this data. 16.
After the Upgrade 21. Log in as craft. 22. With the cursor on the command line, enter test lan. The following screen will appear. 23. Press the ENTER (F3) function key to begin the test. The test takes up to 2½ minutes to run. If any of the individual tests fail or abort, refer to DEFINITY AUDIX System — Maintenance book, 585-300-110. If there are problems with the network itself, the LAN system manager will have to resolve these problems before proceeding with this test. 24.
Upgrades to R3.2 25. This is an Optional step. If Intuity Message Manager has been enabled, have several customers use the Intuity Message Manager system. They should be able to log into their mailbox, play a new message, and reply to sender. (For more detail, see the Intuity Message Manager User Guide, 585-310-725.
Announcement Set Considerations and Installation A This appendix describes customized announcement and fragment considerations, and the installation of additional language sets. Customized Announcement and Fragment Considerations DEFINITY AUDIX R3.2 standard and abbreviated announcements are installed during an upgrade. There have been no changes to announcements between releases 3.1 and 3.2. Any announcements or fragments, however, added or changed by the customer in a release prior to 3.
Announcement Set Considerations and Installation Customer Modified Announcements Normally, announcements are not added or deleted but are often modified by the customer. If additions or deletions were made, Tier 3 engineers should be contacted. For modified announcements, the customer should consider the viability of using them in the upgrade. The following question must be considered: Did the standard announcement change from R1.0/R2.0/R3.0 to R3.
Installing Ad ditional Language Sets The recorded words in the fourth column are announcement set identifiers used when system administrators edit announcement sets. For all announcement sets, these names are played in Announcement #855. NOTE: The following table offers a representative list of announcements. The list of available announcements constantly changes. Contact your AT&T representative for an up-to-date list.
Announcement Set Considerations and Installation 5. Type add tape and press RETURN . The add operation takes approximately 15 seconds and is done in the background. When the operation is complete, the Status Tape screen will show In service, idle. 6. Restore the new language set onto the disk by typing restore backups and pressing RETURN . To confirm this operation, press RETURN again. 7. Type remove tape and press RETURN . Remove the new language tape and insert the original backup tape. 8.
Option Settings B This appendix contains a list of option settings for supported terminals and modems. However, this appendix does not provide procedures for setting the options. Refer to the appropriate manual supplied with the terminal and modem for these procedures.
Option Settings PC/G3MA User Option Settings Table B-1. PC with G3MA User Option Settings Option Setting Color default (original screen colors) customized (redefined colors) lcd (for laptop/notebook screens) monochrome (without color) Mouse speed slow, medium, fast Beep tone yes, no Flashing line? yes, no Operating system DOS, UNIX 715 BCT Option Settings Table B-2.
Terminal Option Settings Assumes a direct connect or a 9600 baud modem. Table B-3.
Option Settings Only the options shown in bold type are critical to terminal operation. Table B-4. 715 BCT General Option Settings Option Window 1 (Switch) Window 2 (Audix) Emulation BCS BCS Terminal ID BCS1 BCS Newline on LF no no Transmit controls 7 bits 7 bits Backspace mode normal normal User features unlocked unlocked Conceal answerback no no 1. This option may be set to track Only the settings shown in bold type are critical to terminal operation. Table B-5.
Terminal Option Settings Table B-6. 715 BCT Keyboard Option Settings Option Window 1 (Switch) Window 2 (Audix) Caps/Shift lock key caps lck caps lck RET CR CR Enter key ent1 Autorepeat yes yes Margin bell yes yes Compose key enabled enabled Break key enabled enabled Keyboard language US US Numeric pad numeric numeric Cursor keys normal normal Swap delete yes yes Control key swapping none none BS BS Legends User defined keys Backspace key 1.
Option Settings When installing a 473/474 parallel printer, set the printer options below. Table B-7.
Terminal Option Settings 513 BCT Option Settings Table B-8.
Option Settings 610 BCT with a 513 Emulation Package Option Settings Table B-9.
Terminal Option Settings 615 BCT with a 513 Emulation Package Option Settings Table B-10.
Option Settings 4410 and 5410 Terminal Option Settings Table B-11. 4410/5410 Option Settings Option Setting Speed 9600 Parity space Duplex full Screen 80 Return key CR Rec’vd LF index Labels on Monitor mode off Key click off Autowrap on Cursor block Built-in modem no Only the settings shown in bold type are critical to terminal operation.
Terminal Option Settings 4425 and 5425 Terminal Option Settings Table B-12.
Option Settings For auxiliary printer option settings on the 4425/5425, set the options on the printer as described in the manual supplied with the printer, then set the corresponding options on the terminal to match. 4415 and 5420 Terminals Table B-13.
Modem Option Settings Modem Option Settings AT&T 2400 Modem Option Settings The AT&T 2400 Modem is shipped from the factory with default option settings. Some of the default settings may not be appropriate when this modem is used with the DEFINITY AUDIX System. You should set the options at your terminal as described below. You should set the options listed in the table in the following section, Software Settings.
Option Settings Jumper Setting A jumper switch is located inside the front endcap of the modem. The jumper must be set to the command mode when setting the options listed in the previous section. After setting the options, the jumper must be set to the noncommand mode for normal operation with the DEFINITY AUDIX System. To access the jumper switch, the front endcap of the modem must be removed. First turn off the modem and disconnect it from the power source, the telephone line, and the computer.
Modem Option Settings There are three jumper pins (labeled JP1) on the left side of the circuit board. When the jumper plug connects the left and middle pins (as shown in the figure), the modem is in the noncommand (dumb ) mode. When the jumper plug connects the right and middle pins, the modem is in the command mode (the factory setting).
Option Settings DM424 Modem Option Settings Change the following options from their defaults. Only the options that require changing are listed — leave the defaults for all others. ■ On the DEFINITY AUDIX system PORT A* modem, set the modem to the Answer Only Mode of Operation (refer to the manual supplied with the DM424 modem for details) ■ Also, set switch 2 to the ON position (modem does not recognize AT commands; dumb mode) ■ After setting switch 2, turn the modem off then back on.
Modem Option Settings 2212D Modem Option Settings Set the switches on the 2212D modem as follows: Option Switch Rocker Number 1-N (O=Open, C=Closed) S1 OOOCCCCC S2 OOOO Also, make sure you press the HS button on the front of the 2212D modem. NOTE: This modem can be used only at 1200 baud. Make sure you set the terminal option accordingly. MPDM Data Module Option Settings This data module can be connected to PORT A for CL integration, or to either PORT A or PORT B for DS integration.
Option Settings CL Integration Set the following MPDM options to the ON switch position if running CL integration: ■ 9600 (baud rate) ■ SYN ■ INT ■ AANS ■ Set all other options to OFF 7400A Data Module Settings In the set interface option menu, set the ANS ONLY? option to YES.
Modem Option Settings 7400B Data Module Settings Set the two dip switches located under the top panel of the 7400B data module as follows: ■ SW1-1: — Set to ON if a telephone is not attached to the 7400B — Set to OFF if a telephone is attached to the 7400B ■ SW1-5: 0set to ON See 7400B Plus Data Module User’s Guide, 555-020-710 for instructions on how set options on the 7400B data module.
Option Settings B-20 Issue 1 September 1995
PEC Explosions C This appendix contains a list of Price Element Codes (PEC) for primary and optional components comprising the DEFINITY AUDIX System.
PEC Explosions Complete System Table C-1.
Complete System Table C-1.
PEC Explosions Primary Equipment Only the multifunction board, alarm board, disk and tape drives listed in the following table are stocked regionally; cables and miscellaneous parts must be ordered directly from the factory. Table C-2. Identifiers for Primary Hardware Description PEC Comcode, ED/H/J Drawing Qty Notes TN566B MFB 70494 107 083 651 1 Included in basic package listed in Table A1, or can be ordered separately.
Primary Equipment Table C-2. Identifiers for Primary Hardware — Continued Description PEC Comcode, ED/H/J Drawing Qty 70572 40-Hour Disk Drive New 1.05 GigabyteDisk, 600 Megabyte Tape Drive 70572A ED1E54670 G-9 70573 407 260 256 ED1E54670G-8 New 40 hour disk 70573A 407 260 256 ED1E54670G-8 Aftermarket 40 hour disk TN2169 ALB 106 433 063 1 1 ED1E54670 G11 TN2170 ALB Notes 70493 106 433 071 1 Aftermarket 1.
PEC Explosions Table C-2.
Primary Equipment Table C-2. Identifiers for Primary Hardware — Continued Comcode, ED/H/J Drawing Qty 406 546 176 3 406 580 837 4 406 602 045 4 —Cable ties 401 077 862 2 —Retainer, spring 846 751 766 1 406 680 843 2 Description PEC —Screws, machine Notes slotted hex— SEMS .138-32x5/16 —Screws, machine slotted hex— SEMS .
PEC Explosions Identifiers for Primary Hardware — Continued Table C-2. Description PEC Opto-isolator attribute ISO 01 Control Link direct-connect cable1 70441 M-M RS-232 Group 311 cables: Comcode, ED/H/J Drawing Qty Notes 106 005 242 2 M-F RS-232 116A (DC-powered switch only) H600-406 G1 1 Factory installed, 1.
Primary Equipment Table C-3. Identifiers for Primary Software — Continued Description RTU Networking PEC Comcode, ED/H/J Drawing Qty Notes 1253-S50A 5 hours for 49+ hours aftermarket 1253-VPC RTU credit for 5 hours 1253 -VSU RTU indicator for 5 hour blocks used in a DEFINITY AUDIX upgrade 1253 VHC PEC migration.
PEC Explosions Table C-3. Identifiers for Primary Software — Continued Description PEC Software for new R3.2 systems. Includes program tape, installation, and documentatio n. (If an upgrade only, pair with 1253-ZDA only. Note that language attributes are different.) 70570 Comcode, ED/H/J Drawing Qty Notes 1 Paired with either 1253-DDA for a new system, or with 1253-ADA fo aftermarket system, or 1253 ZDA, which is the upgrade for R3.2.
Primary Equipment Table C-3.
PEC Explosions Table C-3. Identifiers for Primary Software — Continued Description PEC Comcode, ED/H/J Drawing Qty Notes Right To Use (RTU) for two additional voice ports on a NEW switch 1253-DVP 011 111 111 2 Two ports are included with basic package. Extra ports ordered separately. RTU for Two Additional Voice Ports on an EXISTING Switch 1253-DVPA 011 111 111 2 RTU for Multilingual option 1253-MLF RTU American English 123 1253-DNU 1 Allows up to nine languages.
Primary Equipment Table C-3. Identifiers for Primary Software — Continued Description PEC British English cartridge tape 70489 RTU Canadian French 1253-DCF Comcode, ED/H/J Drawing Qty Notes 1 Paired with one of the above RTUs. (replaces 70414) 107 015 877 1 New systems. 1253-DCFA 1 After-market additions. 1253-CFU 1 Upgrades already having this language. Canadian French cartridge tape 70489 1 Paired with one of the above RTUs. RTU Latin Spanish 1253-DLS 1 New systems.
PEC Explosions Table C-3. Identifiers for Primary Software — Continued Description PEC Dutch cartridge tape RTU Portuguese Comcode, ED/H/J Drawing Qty Notes 70492 1 Paired with 1253-DDU for new systems or with 1253-UDU for upgrades already having this language. Not applicable for R3.1, R3.0, R2.0, or R1.0. 1253-DPO 1 New systems. 1253-DPOA 1 After-market additions. 1253-POU 1 Upgrades already having this language.
Primary Equipment Table C-3. Identifiers for Primary Software — Continued Description PEC Comcode, ED/H/J Drawing Qty Notes RTU TDD 1253-DTD 107 145 013 1 New systems. 1253-DTDA 1 After-market additions. 1253-TDU 1 Upgrades already having this language. 70490 1 Paired with 1253-DTD for new systems, or with 1253-TDU for upgrades already having this language. Not applicable for R2.0 or R1.0.
PEC Explosions Peripheral Equipment All peripherals are optional to the order. However, the customer must provide at least one terminal for DEFINITY AUDIX System administration/maintenance. See the Installing the Terminal(s) worksheet for terminal information. Table C-4.
Peripheral Equipment Table C-4. Identifiers for Peripheral Equipment — Continued Description PEC Comcode, H/ED Drawing Model 2830 Telecommunication s Device for the Deaf (TDD) 3780-004 406 613 265 Z3A-1 male ADU 2169-001 Z3A-2 ADU 2169-002 Z3A-4 female ADU 2169-004 Power supply for ADUs 21691 Qty Notes 1 Must have buffer if Automatic Attendant menus are used. 1 Optional for remote admin. (paired with Z3A-4) Optional for digital networking 102599354 1 Optional for remote admin.
PEC Explosions Table C-4.
Intuity Message Manager (IMM) Intuity Message Manager (IMM) Table C-7. Identifiers for Message Manager Description PEC Comcode Notes RTU MM interface activation via the init screen 1253-IVM Includes capacities of 32 sessions and up to 500 clients. MM Upgrade Kit 70493 Includes TN2170, 3-way splitter cable to make the LAN connection, and the upgrade software for MM.
PEC Explosions C-20 Issue 1 September 1995
Abbreviations ABB ASC Audio Session Control ATTOMS AT&T Order Management System A AUCC AUDIX Upgrade Control Center ABP Alarm Board Processor AUDIX Audio Information Exchange AC AWG American Wire Gauge Alternating Current ACD Automatic Call Distribution ACM Assistant Contract Manager B ADAP Administration and Data Acquisition Package BPS Bits per second ADC Analog-to-Digital Converter BMPM Board Mounted Power Module ADM Administration Manager BTU British Thermal Unit ADU Asynchronous Data Un
Abbreviations DS1 Digital Service 1 D DAC Dial Access Code DC Direct Current DCIU Data Communications Interface Unit DCP Digital Communications Protocol DCS Distributed Communications System DD DSI Digital Service Interface DSIC Dedicated Switch Installation Crew DSP Digital Signal Processor DTE Data Terminal Equipment DTMF Dual Tone Multifrequency DUSCC Dual Synchronous Channel Chip Disconnect Detect DDD Direct Distance Dialing DID Direct Inward Dialing DIO DSP Input/Output Controller DIOD Direct Inwar
Abbreviations FIFO First-In First-Out ISP FP ISDN Integrated Services Digital Network Feature Processor FPROM Flash Erasable Programmable Read Only Memory In Service Pending ITAC International Technical Assistance Center FSA File System Administrator FSO Field Service Organization K FW Kbps Kilobits per second Flashware Kbyte Kilobyte (1024 bytes) kHz kilohertz G GBCS Global Business Communications Systems GBCSDC Global Business Communications Systems Design Center L LAN Local Area Network LA
Abbreviations MFAT Multifunction Analog Telephone MFB Multifunction Board MHz Megahertz MM Message Manager MOJ Material on Job MP Maintenance Procedure MPDM Modular Processor Data Module O OA&M Operations, Administration, and Maintenance OOS-D Out of Service Due to insufficient translations OOS-F Out of Service Fault OOS-R Out of Service Resource OOS-T Out of Service Testing OS Operating System MPM Maintenance Procedure Manager ms Millisecond MSB Mass Storage Bracket MSC Message Service Center P PBX Pri
Abbreviations STU Standalone Tape Utilities R RAM Random Access Memory RISC Reduced Instruction Set Computer RMT Remote Maintenance Terminal ROM Read Only Memory RNX Route Number Index RTU Right to Use T TBD Tone Based Disconnect TCP/IP Transmission Control Protocol/Internet Protocol TD Target Driver TDD Telecommunications Device for the Deaf TDM Time Division Multiplex TEG Trunk Equipment Group S SAKI Sanity and Control Interface SA TSC Technical Service Center TSO Technical Services Organization Sof
Abbreviations VD Voice Data VM Voice Messages VSC Voice Session Control W WGS Work Group System ABB-6 Issue 1 September 1995
Glossary GL NUMERIC 10BaseT A network baseband medium using twisted pair wire, operating at 10 Mbits per second. A Activity Menu The list of main options voiced to subscribers when they access the DEFINITY AUDIX System. Administration The process of setting up a system (such as a switch or a voice mail system) so that it will function as desired. Options and defaults are normally set up (translated) by the system administrator or remote services personnel.
Glossary Audio Messaging Interchange Specification (AMIS) An analog networking feature that allows subscribers of different voice mail systems to send voice mail messages to one another. Audit A software program that resolves filesystem incompatibilities and updates restored filesystems to a workable level of service. Audits are done automatically on a periodic basis, or can be performed on demand.
Glossary C Call Answer A feature that allows the system to answer a call and record a message when the subscriber is unavailable. Callers may be redirected to the system through the call coverage or Call Forwarding switch features. Subscribers may record a personal greeting for these callers. Call Answer Language Choice Call answer multilingual option where a user can alternate between a primary language set and a secondary language. The two languages are administered on a per subscriber basis.
Glossary D Digital Communications Protocol (DCP) An AT&T proprietary protocol DCP Mode 1 An AT&T proprietary Digital Communications Protocol (DCP) connection using a data rate of 56 Kbps for AUDIX Digital Networking. DCP Mode 1 uses a DS1 facility on the switch or a dedicated facility on the switch or a dedicated facility on a T1 carrier. DCP Mode 2 DCP Mode 2 is an asynchronous, low-speed (9600 or 19,200 bps) connection for AUDIX Digital Networking.
Glossary E Errors Problems detected by the system during automatic self-tests and recorded in an error log. Errors can produce an alarm (fault) if they exceed a threshold. Events Occurrences such as inline errors, maintenance procedure failures, alarms, errors, or transitions into or out of the AUDIX or OA&M states which are recorded in an events log. F Faceplate and Alarm Controller (FAC) The circuitry on the Multifunction board which monitors activity of the DEFINITY AUDIX System.
Glossary H Header Information that the system creates to identify a message. A message header includes the originator or recipient, type of message, creation time, and delivery time. Hunt Group A group of ports on a switch usually administered to search for available ports in a circular pattern. I Initialization The process of bringing a system to a predetermined operational state.
Glossary Local Maintenance Terminal (LMT) A display terminal located near the DEFINITY AUDIX System and the switch. It is temporarily attached to the Multifunction board via a Y-cable during an on-site service visit. Login A unique code used to gain approved access to a subscriber's voice mailbox or to a display terminal. M Mailbox A portion of disk memory given to each subscriber for creating and storing outgoing and incoming messages.
Glossary O Operating System (OS) The set of programs that runs the hardware and interprets software commands. Operations, Administration, and Maintenance (OA&M) A state of system operation where core processes of the Multifunction board are accessed, including system initialization, resource configuration, forms interface, entry into the maintenance subsystem, and filesystem access. Also entered when customer data must be restored.
Glossary S Sanity and Control Interface (SAKI) An integrated circuit that receives and transmits TDM bus control messages and monitors the sanity of the angel processor. Shutdown States States of system operation where either a technician can shut down the system for maintenance, or where a critical error condition brings down the system. In either case, filesystems are closed and the system can be powered down and removed from the carrier.
Glossary U Update A limited incremental change on an existing release involving software only. Upgrade The replacement of one release with a new release. This may involve software, flashware, hardware, and/or data.
Index IN 104A mounting block, 7-22 116A opto-isolator, 2-6 715 BCT terminals, 3-3, B-1 7400A data sets, 2-20 ADUs, 2-18 Alarm board location, 2-3 cable connector, 2-9 clearing logs, 4-16 LCD, 2-7 origination, 4-2 status, 3-26 Announcement set identifiers, A-2 Audit switch names, 3-25, 3-34, 5-4 switch translations, 3-14, 3-22 A C Acceptance tests add subscribers, 4-8 Call Answer feature, 4-10 clearing logs, 4-16 DCS subscribers, 4-11 LAN, 4-15 switch link, 4-7 tape, 4-13 Voice Mail feature, 4-10 Activ
Index set switch-link parameters, 3-18 switch number, 4-9, 4-10 test subscribers, 4-10, 4-11 DEFINITY AUDIX system assembly, 2-3 assembly installation, 2-5, 2-6 LCD display, 2-7 slot locations, 2-4 Digital line interface, 2-25 Disk location, 2-3 DSU, 2-27 E Equipment primary, C-4 Error logs, clearing, 4-16 G G3vs slot locations, 2-4 J Joint acceptance tests, 4-15 L Language sets, installing new, A-3 Liquid crystal displays (LCDs), 2-7 Login craft, 3-4 init, 3-6 M Machine ID, 3-13, 3-18 Message Manager
Index P Packet gateway, 2-26, 2-27, 2-28 Parameters, activating, 3-29 Parts missing, 1-4 required and optional, 1-4 PC using G3MA, B-1 PEC explosions, C-1 Port activate, 3-4, 3-7 switch, 3-18 voice, 3-15 Power warning, 2-2 Powering down the switch, 2-2 Price element codes complete system, C-1 peripheral equipment, C-16 primary hardware and software, C-4 Primary hardware and software, C-4 Printer installation, 2-29 Processor interface (PI), 2-23 Project review, 6-2 system-parameters customer options, 3-4 s
Index Tools, 1-3 V Voice ports, 3-15 W Walk-through, 6-1 Worksheets acceptance tests, 4-2 hardware installation, 2-2 subscriber administration, 5-2 system administration, 3-2 IN-4 Issue 1 September 1995
