^ -
INSTALLATION BeforeYou Install Use only the power cord supplied with this product. If you need a replacement,call 1 8O0222-3llt. Input: 12OY 6OHz. Output: 6VAC,35O mA. Choose a location for the answering system ne r a modular telephone lack and a standard electrical outlet not controlled by a wall switch. NOTE: If you do not uant to connect a telepbone, skip Step 2. Table/DeskInstallation Modular Telepbone Jack L Connect the telephone line cord. 'rc Standard.
F E A T U R ES E T U P Turn System On/Off Press loltzorrlto turn the system on or off. The messagewindow will display information when the system is on. FeatureSetup 1 2 To enter Feature Setup mode, press and hold FrruFl until the system announces "Selectedannouncerrrent is..." Press and release [SrrttF unti] the svstem announces the feature vou want to set. Press and release Funaml orWEttlnEFEM until the s)-stemannounces the setting you want. Refer to the Feature Summary for options.
F E A T U R ES E T U P FeatureSummary(cont'd) RemoteAccessCode "Remote access code is..." Change the Remote Access Code to any three digit number from 5OOto 999. Do not set to same number as Priority Calling Code. . The RemoteAccess Code, preset to 5O0,allows you to access many features of this answering system remotely from a touch tone phone. . The system will prompt you to repeat Steps 2 and 3 of Feature Setup until you have set all three digits.
F E A T U R ES E T U P ,:Qrt: FeatureSummary(cont'd) Call Screening Set the s\'stem to hear callers'messagesas they are being recorded (O\) or to remain silent while callers are recording messages(OFF). Call Screening is preset to ON. NOTE: Volume must be set to a letel lou can bear to use Call Screening. ReviewFeatureSetup To review the current feature settings. press and release EETuA. _,-;.--:. .
OPERATION Listen To,Save& Delete l'lessages time the message was received. ff Store Number is set to ON, the system also announces the caller's telephone number (see "Store Number"under FEATURESETUP).After playing the last message,the system announces "End of ntessages." The system automatically savesyour messagesuntil you delete them. You can store approximately 4O minutes of messages,memos, and announcements (up to a maximum of 119 messages).
OPERATION Set the Clock You must set the clock once for the system to announce the correct day and time with your messages.A-fter this. if t-ou subscribe to Caller ID. the svstem s'ill automaticalh'reset the clock each time new call information is receil-ed. Cfhere is a fee for Caller ID sen'ice , and it may not be available in all areas.) Press WSIMSTIA to exit at any time while setting the clock. 1- Press and hold [EZocrluntil the default day is announced. 2 To change the day setting.
OPERATION AnsweringCalls Recorda ilemo When you ve selected annormcement 8, b, or f, and the system answers a call, the caller hears the announcement you recorded, followed by a beep. During the announcement, callers can pfess I,2,or 3 to select a mailbox, or they can wait for the beep to leave a messagein Mailbox 1. After the beep, the system begins recording your caller's message. A caller can leave a messageup to three minutes long.
r I R E M O T EO P E R A T I O Connectwith the AnsweringSystem You can access many features remotely from a touch tone phone. 1 Dial your telephone number. 2 When the system answefs, enter youf three-digit RemoteAccess Code during or after the announcement. The system announces the number of messages, then begins playing back new messages in Mailbox 1.
I N C A S EO F D I F F I C U L T If you have difficulty operating this product, try the suggestions below. For Customer Service, visit our website at u)uxa.telep b one s.att. com or call 1 8OO222-31 1 1. Please retain your receipt as your proofofpurchase. System Does Not Respond To Remote Commands . Make sure you are calling from a touch tone phone . When you dial a number, you should hear tones. Ifyou hear clicks instead, the phone is not a touch tone telephone. .
I N C A S EO F D I F F I C U L T l'lessage Window ls Blank . Make sure the power cord is securely connected (and threaded through the strain relief tab) to both the answering system and an electrical outlet not controlled by a wall switch. . Press @unFFlto make sure the system is on. Message Window Displays Power Failure Recovery If the system is disconnect€d fromAC power it will not operate. Your announcement and messagesare retained in memory during a power failure but you will need to reset the clock.
