555-230-223 January 1996 DEFINITY Communications System Generic 3 Installation, Administration, and Maintenance of CallVisor ASAI Over the DEFINITY LAN Gateway
Copyright 1993 AT&T All Rights Reserved Printed in USA Notice While reasonable effort was made to ensure that the information in this document was complete and accurate at the time of printing, AT&T cannot assume responsibility for any errors. Changes and/or corrections to the information contained in this document may be incorporated into future issues.
bbbbb bb bb bb bb bb bb b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb Contents bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb About This Book Purpose Intended Audience Prerequisite Knowledge How this Book is Organized Documentation Conventions Related Documents iii iii iii iv iv v v bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb 1 Introduction Overview of CallVisor ASAI Over the DEFINITY LAN Gateway Upgrading Your Existing System Security Considerations 1-1 1-1 1-5 1-5 bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb 2 Installat
bbbbb bb bb bb bb bb bb bb b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb Contents Worksheet A-1: Port Slot Assignments (Before Carrier Arrangement) Worksheet A-3: Port Slot Locations for the DEFINITY LAN Gateway System Assembly A-2 A-4 bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb B Appendix B: Supported Terminals and Modems/Option Settings Worksheet B-1: Terminals/Modems Option Settings B-1 B-2 B-3 bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb C Appendix C: Ordering Information Complete System Primary Equipment C-1
bbbbb bb b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb Contents bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb IN Index IN-1 iii
bbbbb bb bb b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb Figures bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb 1 Introduction 1-1. DEFINITY LAN Gateway System Assembly 1-3 bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb 2 Installation 2-1. 2-2. 2-3. 2-4. 2-5. 2-6. 2-7. 2-8. 2-9. bb 2-10. 2-11. 2-12. 2-13.
bbbbb bb bb bb bb b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb Tables bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb 3 System Administration 3-1. Function Keys 3-4 bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb 4 Maintenance 4-1. 4-2. 4-3. System Capacities, Requirements, and Limitations System States Maintenance Terminal Hookups 4-2 4-6 4-12 bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb B Appendix B: Supported Terminals and Modems/Option Settings B-1.
bbbbb bb b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb Screens bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb 2 Installation 2-1. 2-2. 2-3. 2-4. 2-5. 2-6. 2-7. 2-8. 2-9. bb Change Circuit-Packs List Configuration Add Station Main Menu This Host Main Menu Ping Host Screen Results of Pinging the DEFINITY LAN Gateway Results of Pinging the Client 2-30 2-30 2-31 2-33 2-34 2-35 2-37 2-38 2-39 bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb 3 System Administration 3-1. 3-2. 3-3. 3-4. 3-5. 3-6. 3-7. 3-8. 3-9. 3-10. 3-11. 3-12.
bbbbb b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb Screens 3-25. 3-26. 3-27.
bbbbb b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb About This Book bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb b bbbbbb b bbbbbb Purpose This book covers the CallVisor ASAI DEFINITY LAN Gateway system that provides Adjunct Switch Application Interface (ASAI) functionality using an Ethernet transport. Its purpose is to explain the tasks involved in installing, administering, and maintaining a DEFINITY LAN Gateway system.
bbbbb About This Book b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb b bbbbbb b bbbbbb Prerequisite Knowledge Anyone administering ASAI over the DEFINITY LAN Gateway should possess basic knowledge of DEFINITY system administration. (It is assumed the user of this guide can administer ASAI links.) In addition, some knowledge of Transport Connection Protocol/Internet Protocol (TCP/IP) is recommended.
bbbbb About This Book b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb Glossary Defines terms and acronyms used in the guide b bbbbbb Index Provides help in locating information in the guide quickly and easily Documentation Conventions The following conventions are used in this document: The full title of the product described in this document is CallVisor ASAI Over the DEFINITY LAN Gateway. It is sometimes shortened to ‘‘DEFINITY LAN Gateway’’ in this guide.
bbbbb About This Book b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb used for transporting messages in CallVisor ASAI Over the DEFINITY LAN Gateway. This document is the companion to the following document (555-230-220). DEFINITY Communications System Generic 3 CallVisor ASAI Technical Reference, 555-230-220 This document provides a detailed functional description of CallVisor ASAI for the Generic 3 switch. Issue 4.
bbbbb b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb Introduction 1 bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb b bbbbbb Overview of CallVisor ASAI Over the DEFINITY LAN Gateway CallVisor ASAI over the DEFINITY LAN Gateway is a communications interface that provides the functionality of the Adjunct/Switch Application Interface (ASAI) using an Ethernet transport instead of a Basic Rate Interface (BRI) transport.
bbbbb Introduction b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb CallVisor ASAI Over the DEFINITY LAN Gateway is provided with a default set of administered parameters, but customers can also administer the LAN parameters and client information to conform to their networks. NOTE 1: AT&T support services for the DEFINITY LAN Gateway system will not troubleshoot a customer LAN. If the customer LAN is experiencing difficulties, customers should follow the escalation path supplied by their LAN provider.
bbbbb Introduction b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb bbbbbbbbbbbbbbbbbbbbbbbb I2C bus cable SCSI bus cable Power cable Tie wrap Multi-Function board (TN2208) Alarm board (TN2170) Retaining pins Tape drive (without cover) ENTER / YES &T AT BACK NEXT / NO Disk drive SCSI bus cable Power supply bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb Figure 1-1. DEFINITY LAN Gateway System Assembly NOTE: The system assembly is also used to support DEFINITY AUDIX .
bbbbb Introduction b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb The DEFINITY LAN Gateway system assembly can be distinguished from the DEFINITY AUDIX system assembly by the ‘‘TN’’ codes on the circuit packs and by a DEFINITY LAN Gateway label. The DEFINITY AUDIX system assembly uses TN566 (not shipped on new systems), TN566B, TN567, and TN2169 or TN2170. The DEFINITY LAN Gateway system assembly uses TN2170 and TN2208. The TN2170 circuit pack supports a hard disk, Ethernet controller, and removable media.
bbbbb Introduction b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb b bbbbbb Upgrading Your Existing System If you want to have CallVisor ASAI over the DEFINITY LAN Gateway in a non-supported switch, you must upgrade it with a field maintenance release of G3V4 software. Contact the Technical Service Center at 1 800 248-1234 for more information. (You will be prompted for your Social Security Number and 4-digit PIN.
bbbbb Introduction b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb unauthorized client access attempts, time of Multi-Function Board resets, and commands executed from Administration/Maintenance screens. This system does not support an encrypted/secured protocol; therefore, it is possible for a criminal hacker to ‘‘spoof’’ the system by reverse engineering the protocol and then ‘‘impersonating’’ a valid DEFINITY LAN Gateway client.
bbbbb b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb Installation 2 bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb This chapter consists of three sections: Prerequisites Hardware Installation Initial Administration NOTE: This chapter is for AT&T services personnel. Normally, AT&T installs the DEFINITY LAN Gateway system. However, the customer is responsible for DEFINITY switch administration during installation.
bbbbb Installation b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb bbbbbbbbbbbbbbb Task 1: Verify the Selected Site NOTE: Defining the system requirements and ensuring that the site meets these requirements are the responsibility of the Project Manager and the customer and must be completed before you install the DEFINITY LAN Gateway system. However, the guidelines are listed here so that you are aware of these requirements.
bbbbb Installation b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb Humidity range of 20% to 80%, noncondensing. In addition, make sure the site is secure and provides protection from excessive sunlight, heat, cold, chemicals, static electricity, magnetic fields, vibration, and grime. NOTE: ASAI must be enabled on the DEFINITY Customer Options form for the system to be fully operational.
bbbbb Installation b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb bbbbbbbbbbbbbbb Task 4: Verify Components and Connectivity Study Figure 2-2 that follows to gain a general understanding of how the system assembly is to be connected. Some customer-furnished LAN equipment is included within the dotted lines in this figure. Helpful definitions for this equipment are as follows. Balun (balanced/unbalanced) — An impedance matching transformer.
bbbbb Installation b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb bbbbbbbbbbbbbbbbbbbbbbbb (Not Used) Telnet Management Client 10BaseT ❶ (Twisted Pair) Balun Ethernet Coaxial Cable Switch Alarm Board ALB Cable DEFINITY LAN Gateway Client ❷ LAN Server RJ45 DEFINITY LAN Gateway Client ❷ Telnet Management Client LAN Server 10BaseT ❶ (Twisted Pair) TN2170 RS-232 10BaseT HUB ❸ Null Modem H600-258 G1 ❹ Modem T/R Modem Admin/Port B Z3A4 MultiFunction Board MFB Y Cable House Wiring Z3A1 T
bbbbb Installation b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb Refer to the diagrams in Tasks 6 and 7 in section 2 of this chapter, Hardware Installation, for additional connectivity details. Then compare the parts listed in Appendix C, ‘‘Ordering Information’’ with the actual parts you received to make sure that all required parts have been ordered and shipped correctly. NOTE: The components listed in Appendix C are not the only equipment that can be used with the DEFINITY LAN Gateway system.
bbbbb Installation b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb b bbbbbb Hardware Installation This section describes the tasks needed to install the DEFINITY LAN Gateway system hardware and peripheral hardware. The DEFINITY LAN Gateway system installation tasks are the same for all switch types.
bbbbb Installation b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb For the same reason, do not cycle the power on the switch (for example, during switch acceptance tests) once the system assembly is inserted unless you have first shut down the DEFINITY LAN Gateway system. Refer to the maintenance screens in Chapter 3 for the shutdown procedure.
bbbbb Installation b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb bbbbbbbbbbbbbbbbbbbbbbbb Example of DEFINITY LAN Gateway Slots 5th 4th 3rd 2nd 1st 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 ALB Cable (H600-353-G2) Amphenol Connector (not used) Female RJ45 Female RS-232 MFB Y-Cable (H600-352-G1) bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb Figure 2-3.
bbbbb Installation b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb NOTE: You must connect these adapter cables directly to the port connectors on the switch. If you install another cable between the switch and the cables, the DEFINITY LAN Gateway system will not operate correctly (either now or in the future). a.
bbbbb Installation b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb bbbbbbbbbbbbbbbbbbbbbbbb I2C bus cable SCSI bus cable Power cable Tie wrap Multi-Function board (TN2208) Alarm board (TN2170) Retaining pins Tape drive (without cover) ENTER / YES &T AT BACK NEXT / NO Disk drive SCSI bus cable Power supply bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb Figure 2-4. DEFINITY LAN Gateway System Assembly ! WARNING: The DEFINITY LAN Gateway system will automatically boot when seated in the slots.
bbbbb Installation b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb 5. Insert the assembly and lock it in place by pushing up the securing latches on the two circuit packs. (It is normal for the two circuit packs to feel loosely connected to each other. This is to allow some give when you are seating them into the two slots of the backplane.) If the switch is powered on, the DEFINITY LAN Gateway system will boot automatically.
bbbbb Installation b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb When the DEFINITY LAN Gateway system is coming up, the LCD should display the following states (in order): BTEST BOOT OSINIT OS AINIT ASAI X (Firmware board tests) (Booting the operating system) (Operating system initialization) (Operating system) (DEFINITY LAN Gateway system initialization) (DEFINITY LAN Gateway running with X attached clients) If the system does not come up to the ASAI X state within 30 minutes (10 to 15 minutes is avera
bbbbb Installation b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb bbbbbbbbbbbbbbb Task 6: Connect the Alarm Board Cables The Alarm Board cable has three connectors available for outside connections: Amphenol connector — not used Local Area Network (LAN) RS-232 Maintenance — used for local customer access to the DEFINITY LAN Gateway application Figure 2-6, Alarm Board Cable Connections, shows how the cables should be connected.
bbbbb Installation b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb Group 300 Cable Connection The DEFINITY LAN Gateway does not use this connection. LAN Connection Make the following connections: A 10BaseT twisted pair cable with a male RJ-45 connector must be present at the wall field, no further than 25 feet from the back of the switch where DEFINITY LAN Gateway resides. The customer is responsible for this LAN connection.
bbbbb Installation b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb bbbbbbbbbbbbbbbbbbbbb WE 8 7 6 5 4 3 2 1 To DEFINITY LAN Gateway Alarm Board LAN Connector 8 7 6 5 4 3 2 1 104A 10BaseT LAN Connection bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb Figure 2-7. 104A Mounting Block A D8W modular wall cord (up to 25 feet long) is used to connect the Alarm Board RJ45 connector to the 104A connecting block.
bbbbb Installation b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb TN2170 RS-232 Connection This connection is used for customer access to the DEFINITY LAN Gateway application. See Task 7 for wiring information. bbbbbbbbbbbbbbb Task 7: Install the Terminal (Optional) This task is optional, but the temporary installation described below is recommended to facilitate initial administration of the DEFINITY LAN Gateway application.
bbbbb Installation b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb Keep in mind that the DEFINITY LAN Gateway system is data terminal equipment (DTE), and the switch is data communications equipment (DCE). Therefore, you may need to install a null modem to complete the DTE/DCE pair when connecting the PC. MFB Port Usage The MFB Y-cable has two RS-232C connectors labeled Main/Port A and Admin/Port B. The administration and maintenance terminal should be connected to Admin/Port B.
bbbbb Installation b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb bbbbbbbbbbbbbbbbbbbbb SWITCH ALB CABLE ALARM BOARD ADMIN/PORT B SEE NOTE GROUP 311 MFB Y-CABLE MULTIFUNCTION BOARD CABLE NULL MODEM GROUP 311 CABLE MAIN/PORT A TIP/ RING MODEM AT&T SERVICES REMOTE ACCESS bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb NOTE: NULL MODEM NOT REQUIRED WHEN CONNECTING TO 715 BCT DCE PORT Figure 2-8.
bbbbb Installation b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb 1. If you are installing a new terminal, unpack it according to the instructions supplied with the terminal. 2. Place the terminal on a suitable table within 15 feet of the switch cabinet if you have a 20-foot ED-1E434 Group 311 cable, or within 45 feet if you have a 50-foot ED-1E434 Group 311 cable, and connect the keyboard. 3. Connect an ED-1E434 Group 311 cable between the DEFINITY LAN Gateway system MFB and the terminal: a.
bbbbb Installation b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb Task 7B: Install a Terminal via Modems This task describes how to connect a terminal via a modem to Admin/Port B of the MFB. (This task can also be used for remote connection to the TN2170 RS-232 connector.) To make sure the modems that you are installing are on the list of supported peripherals, see Appendix B, ‘‘Supported Terminals and Modems/Option Settings.
bbbbb Installation b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb c. Plug the modem power cord into a wall outlet and power on the modem. d. Set the modem options. Refer to Appendix B, ‘‘Supported Terminals and Modems/Option Settings,’’ for a list of option settings for supported modems. 3. Connect a modem to the terminal. a. If you are installing a new terminal, unpack it according to the instructions supplied with the terminal. b. Place the terminal on a suitable table and connect the keyboard. c.
bbbbb Installation b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb If the terminal does not display the login prompt when the DEFINITY LAN Gateway system is in one of the above states, try pressing the Return key a few times. If the login prompt still does not appear, write down the state displayed on the LCD, and then see the troubleshooting procedure for terminal connections in Appendix D (to be supplied). k. Log in to the DEFINITY LAN Gateway system (see Chapter 3).
bbbbb Installation b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb b. Plug the cable from the ADU into a telephone outlet. 2. In the terminal room, connect the Z3A-1 ADU to the terminal. a. If you are installing a new terminal, unpack it according to the instructions supplied with the terminal. b. Place the terminal on a suitable table and connect the keyboard. c. Attach the Z3A-1 ADU (male) to a serial RS-232 port on the terminal (the DTE port on a 715 BCT).
bbbbb Installation b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb bbbbbbbbbbbbbbbbbbbbbbbb SWITCH ALARM BOARD ALB CABLE ADMIN/ PORT B MULTIFUNCTION BOARD MFB Y-CABLE GROUP 311 CABLE 7400A SITE-SPECIFIC NETWORK CONNECTIONS POWER SUPPLY (SEE NOTE) 7400B POWER SUPPLY MAIN/ PORT A bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb NOTE: NULL MODEM IS REQUIRED WHEN CONNECTING TO 715 BCT DCE PORT Figure 2-12.
bbbbb Installation b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb c. Connect the 4-pin connector on one of the 7400A power supplies to the POWER connector on the data set, and plug the power supply into a wall outlet. d. Set the options and interface baud rate on the 7400A data set. Refer to ‘‘Using the Front Panel’’ in the 7400A Data Module User’s Manual, 555-020-706, for details. 3. In the terminal room, connect the 7400B data set to the terminal. a.
bbbbb Installation b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb j. Enter ATDT and the phone number of the 7400A data set connected to the DEFINITY LAN Gateway system (refer to Worksheet B-1, ‘‘Terminals/Modems’’ for this number). After a connect interval, if the terminal and 7400 data sets are installed correctly (and the system is in either OAM or OS state), the screen displays the login prompt.
bbbbb Installation b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb a. At the login prompt, type craft and press Return . (If the login prompt is not displayed, press Return once or twice.) NOTE: To send the information to the DEFINITY LAN Gateway system, the Return key (located on the right side of your keyboard) must be pressed after you type a command or a response to a prompt. On some keyboards, this key is labeled Enter instead of Return .
bbbbb Installation b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb b bbbbbb Initial Administration This section describes the tasks required to initially administer the DEFINITY LAN Gateway system. It is expected that these procedures will be performed by AT&T services personnel upon completion of the hardware installation. Preliminary to installation, the Project Manager should complete the form located in Appendix G. After the system is installed, the Project Manager calls the TSC to register the system.
bbbbb Installation b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb change circuit-packs 1 Page 1 of 5 -----------------------------------------------------------------------CARRIER 1A Slot 01: 02: 03: 04: 05: 06: 07: 08: 09: 10: ’#’ Code Name _____ _____ LGATE RESERVED LGATE RESERVED LGATE RESERVED TN2208 LAN GATE LGATE RESERVED _____ _____ _____ indicates circuit LGATE LGATE LGATE BOARD LGATE pack conflict Slot 11: 12: 13: 14: * * * * * * Code _____ _____ _____ _____ Name Use slots A01-A14 with J5
bbbbb Installation b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb The DEFINITY LAN Gateway logically occupies five slots on a port carrier. The screen fields for these four or five slots are described as follows. Board Number: Slot location in the switch. Board Type: For the TN2208 circuit pack, ‘‘LGATE BOARD’’ is displayed for the physical location of the board. ‘‘RESERVED LGATE’’ is displayed for the board’s associated reserved (virtual) slots.
bbbbb Installation b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb bbbbbbbbbbbbbbb Task 11: Perform Initial DEFINITY LAN Gateway Administration This task is required for all installation scenarios. There are two parts to this task: Task 11A: Set the DEFINITY LAN Gateway Clock Task 11B: Assign the DEFINITY LAN Gateway Machine ID (Optional) Task 11A: Set the DEFINITY LAN Gateway Clock 1. At the login prompt, enter craft. The system displays the Password prompt. 2.
bbbbb Installation b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb Release 1.0, Issue x.y Main Menu 1. Login/Password Administration 2. TCP/IP Administration... 3. Brouter Administration 4. Maintenance... 5. Port Status/Control 6. Exit This line is used to provide abbreviated help on the currently selected field. EXIT REFRESH ENTER HELP Screen 2-4. Main Menu 5. Select Maintenance and then Set System Time and Date .
bbbbb Installation b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb TCP/IP Administration This Host Host Name: ______________________________ Host IP Address: __________________ Subnet Mask: __________________ This line is used to provide abbreviated help on the currently selected field. CANCEL REFRESH ENTER CLEAR HELP Screen 2-5. This Host 2.
bbbbb Installation b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb 4410 for a 4410 or 5410 terminal; enter 4410 also for a 610/615 BCT or a PC with a 4410 emulation package. 4425 for a 4425 or 5425 terminal 5420 for a 5420 or 4415 terminal g3-ma for a G3-MA vt220 (or other terminal listed in Appendix B) 4. The system displays the DEFINITY LAN Gateway Main Menu. Release 1.0, Issue x.y Main Menu 1. Login/Password Administration 2. TCP/IP Administration... 3. Brouter Administration 4. Maintenance..
bbbbb Installation b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb bbbbbbbbbbbbbbb Task 13: Test LAN/Client Connectivity (Optional) Task 13 is performed to test the TCP/IP connection to ensure that connectivity exists between the DEFINITY LAN Gateway and the customer’s LAN, as well as between the DEFINITY LAN Gateway and a client. This testing should be done jointly with the customer’s LAN administrator.
bbbbb Installation b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb Maintenance Ping Host Host Name or IP Address: ____________________ Packet count: ___ Packet size: ___ This line is used to provide abbreviated help on the currently selected field. CANCEL REFRESH ENTER CLEAR HELP Screen 2-7. Ping Host Screen b. Fill in the Host Name or IP Address of the DEFINITY LAN Gateway system assembly. This example uses 192.168.25.10 as the IP Address.
bbbbb Installation b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb Output similar to the following will appear: The messages which follow are the result of your last request. At the : prompt press return to continue. 72 72 72 72 72 72 72 72 72 72 bytes bytes bytes bytes bytes bytes bytes bytes bytes bytes from from from from from from from from from from 192.168.25.10: 192.168.25.10: 192.168.25.10: 192.168.25.10: 192.168.25.10: 192.168.25.10: 192.168.25.10: 192.168.25.10: 192.168.25.10: 192.168.
bbbbb Installation b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb d. Now access the Ping Host screen again, as you did in step 2a, to test connectivity to the client. Use the same data, except in this example, enter 192.168.25.20 as the IP address (if you choose to enter IP Address instead of Name). In this step, the DEFINITY LAN Gateway system assembly is sending packet messages (20 in this example) to the client, and listening for responses.
bbbbb Installation b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb The results displayed in the packet loss field (z) will range from 0% to 100% The number of packets that are ‘‘lost’’ (need to be transmitted) will vary from LAN to LAN. For some LANs, 0% packet loss is normal, while for others, 10% or 20% loss is normal. The degree of packet transmission over a LAN depends upon the distance between machines, the number of users on the LAN, and the number of machines on the LAN.
bbbbb Installation b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb bbbbbbbbbbbbbbb Task 14: Register/Back Up the System The final three steps the AT&T service technician performs to install the DEFINITY LAN Gateway system are as follows: Task 14A: Register the System Task 14B: Deactivate/Activate Logins Task 14C: Perform a Backup of the Removable Medium Task 14A: Register the System AT&T Services personnel should call the TSC at 1-800-248-1111 to register the system.
bbbbb Installation b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb 3. Rotate the lever on the tape drive to the open (facing down) position (if it is not already open). 4. Referring to Figure 2-13, hold the cartridge with the tape side down and the arrow pointing toward the drive (away from you), then insert the cartridge into the drive. bbbbbbbbbbbbbbbbbbbbb Write Protect tab This side Arrow indicating direction to insert tape Tape side down bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb Figure 2-13.
bbbbb b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb System Administration 3 bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb b bbbbbb This chapter presents the screens used for administering and maintaining the system. Sample configurations are located in Appendix E. Getting Started This section details information about the screens, procedures for logging on, and procedures for moving among screens. bbbbbbbbbbbbbbb Screen/System Conventions Screen and system conventions are listed below.
bbbbb System Administration b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb When the prompt Are You Sure? appears, the user must press after entering Y or N. Return bbbbbbbbbbbbbbb Logging On 1. At the login prompt, enter your login and press Return . The password prompt (PASSWORD:) appears. NOTE: If a login prompt is not displayed, press Return a few times. If it still does not appear, see ‘‘Bringing Up the System’’ in Appendix D. 2. Enter your password and press terminal type as follows: Return .
bbbbb System Administration b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb b bbbbbb Moving Around the System The methods for moving around the DEFINITY LAN Gateway screens are as follows: 1. You can use the function keys on the bottom of the screen ( NXTPG , PRVPG , NXTDAY , and PRVDAY ) to move around screens, as applicable. NOTE: An alternate method of using function keys is to press the Ctrl key, and while holding it down, press F .
bbbbb System Administration b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb bbbbbbbbbbbbbbb bbbbbbbbbbbbbbbbbbbbb Using the Function Keys Table 3-1. Function Keys c c Does this: bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb c c ADD c Appears on two TCP/IP Administration screens: c 1. On Local Host Table screen, provides access to Add c Hosts screen. c c 2. On Network Routing Table screen, provides access to c Add Routes screen.
bbbbb System Administration b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb c c c c c Does this: c Pressing this Key: bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb c c c c On Port Status/Control screen, accesses Message Collection c c MSGPER c c c Period screen.
bbbbb System Administration b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb b bbbbbb List of Screens A list of the system screens and the pages on which they are located in this chapter appears below. This list also depicts the screen hierarchy.
bbbbb System Administration b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb bbbbbbbbbbbbbbbb bbbbbb Field Names and Descriptions Main Menu Release 1.0, Issue x.y Main Menu 1. Login/Password Administration 2. TCP/IP Administration... 3. Brouter Administration 4. Maintenance... 5. Port Status/Control 6. Exit This line is used to provide abbreviated help on the currently selected field. EXIT REFRESH ENTER HELP Screen 3-1.
bbbbb System Administration b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb c Description Item bMenu bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb c c Provides access to maintenance functions: formatting media, Maintenance... c saving and restoring configuration data, setting time and date, c c resetting the system, viewing system/security logs, and c pinging other hosts.
bbbbb System Administration b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb bbbbbbbbbbbbbbb Login/Password Administration Login/Password Administration NOTE: Only the primary administrator is allowed to add or delete logins. (The ADD and DELETE keys only appear for the primary administrator login.) Also, only the primary administrator login can change a password for any login.
bbbbb System Administration b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb Use this screen as follows: To delete a login: 1. Press Tab or use the arrow keys to move to the login you want to delete, and then press DELETE . 2. The following prompt appears: Are You Sure? (Y/N?) . Type Y and press Return . The screen will reappear, minus the deleted login. If you type N and press Return , the cursor reappears at the beginning of the line, and the login is not deleted. 3.
bbbbb System Administration b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb Add Logins Note 1: Only the primary administrator login is allowed to add logins and passwords. Note 2: If the primary administrator attempts to add a login that already exists, an error message is displayed. Login/Password Administration Add Logins Login: _____________ This line is used to provide abbreviated help on the currently selected field. CANCEL REFRESH ENTER CLEAR HELP Screen 3-3.
bbbbb System Administration b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb Use this screen as follows: 1. Type the login you want to add to the system. 2. Press ENTER to submit the login. 3. The following prompt appears: New password: Type the password to be associated with the login and press Return . Passwords follow normal UNIX naming conventions. These are: Each password must have at least 6 characters.
bbbbb System Administration b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb Change Passwords NOTE: Any user may change his or her password. The primary administrator login can change any user’s password. Old Password New Password Re-Type New Password a a a a a a a a a a a a a a a a a a a a a a a lkjljklkjlkjlkjljlkj lkjljklkjlkjlkjljlkj lkjljklkjlkjlkjljlkj lkjljklkjlkjlkjljlkj Some test lkjljklkjlkjlkjljlkj a a a a a a a a a a a a a a a a a a a a a a lkjljklkjlkjlkjljlkja Screen 3-4.
bbbbb System Administration b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb c Description Field Name b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb c c The existing password. Appears on screen only Old Password c for logins other than the primary administrator. b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb c New Password c The password you want to change the existing c c password to Use this screen as follows: 1.
bbbbb System Administration b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb bbbbbbbbbbbbbbb TCP/IP Administration (Main Menu) TCP/IP Administration 1. This Host 2. Local Host Table 3. Network Routing Information... 4. Exit This line is used to provide abbreviated help on the currently selected field. EXIT REFRESH ENTER HELP Screen 3-5.
bbbbb System Administration b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb This Host TCP/IP Administration This Host Host Name: ______________________________ Host IP Address: __________________ Subnet Mask: __________________ This line is used to provide abbreviated help on the currently selected field. CANCEL REFRESH ENTER CLEAR HELP Screen 3-6. This Host This screen is used to assign a host name to the Multi-Function Board. NOTE: For changes to be implemented, you must reboot the system.
bbbbb System Administration b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb c Field Description c O/R* Field Name bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb c c c Subnet Mask used by this circuit pack. Change only if c O Subnet Mask c alternate network subnetting is desired. Value = x.x.x.x, c c c c where x is a number between 0 and 255. Default = blank. c c Maximum field size = 15 characters. c Use this screen as follows: 1.
bbbbb System Administration b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb Local Host Table Page X of X TCP/IP Administration Local Host Table IP Address Host Name Aliases ________________ ________________ ________________ ________________ ________________ ________________ ________________ ________________ ________________ ________________ ________________ ________________ ________________ ________________ _________________________ _________________________ _________________________ _________________
bbbbb System Administration b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb Use this screen as follows: Press NXTPG or PRVPG to access other hosts. To delete a host entry: 1. Press Tab or use the arrow keys to move the cursor to the line you want to delete, and then press DELETE . 2. The following prompt appears: Are You Sure? (Y/N) . Type Y and press Return . When the screen reappears, the host will not appear.
bbbbb System Administration b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb Local Host Table — Add Host TCP/IP Administration Local Host Table Add Host IP Address ________________ Host Name _________________________ Aliases _____________________________ This line is used to provide abbreviated help on the currently selected field. CANCEL REFRESH ENTER CLEAR HELP Screen 3-8. Add Host This screen is used to add hosts.
bbbbb System Administration b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb 3. Access the Add Hosts screen again and repeat steps 1 and 2 for each new host to be added.
bbbbb System Administration b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb Network Routing Information (Main Menu) TCP/IP Administration Network Routing Information 1. Network Routing Daemon 2. Default Gateway 3. Network Routing Table 4. Exit This line is used to provide abbreviated help on the currently selected field. EXIT REFRESH ENTER HELP Screen 3-9.
bbbbb System Administration b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb Network Routing Information — Network Routing Daemon TCP/IP Administration Network Routing Information Network Routing Daemon Network routing daemon state: ___ This line is used to provide abbreviated help on the currently selected field. CANCEL REFRESH HELP STATE Screen 3-10. Network Routing Daemon This screen is used to view and change the state of the network routing daemon.
bbbbb System Administration b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb If you type N and press Return , the state is not changed. When the desired state is displayed, press Routing Information menu reappears. 3-24 Issue 1 January 1996 CANCEL .
bbbbb System Administration b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb Network Routing Information — Default Gateway TCP/IP Administration Network Routing Information Default Gateway Name or IP Address: ____________________ Status: ______ This line is used to provide abbreviated help on the currently selected field. CANCEL REFRESH ENTER CLEAR HELP Screen 3-11. Default Gateway A default gateway allows the Multi-Function Board to communicate with other hosts in other LANs.
bbbbb System Administration b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb Field Name c Description bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb c c Name or IP Address of the default gateway, the machine Name or IP Address c used to route all traffic destined for other networks, for c c which a specific route is not known. Maximum field size bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb c = 20 characters. c Status c Either up or down .
bbbbb System Administration b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb Network Routing Information — Network Routing Table TCP/IP Administration Network Routing Information Network Routing Table Type Destination _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _______
bbbbb System Administration b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb c Description Name bField bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb c c The type of destination, either host or network . (Most Type c routes are to network destinations.) bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb c c Name or IP address of the gateway, the machine used to Gateway c c route all traffic to the given destination.
bbbbb System Administration b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb Network Routing Table — Add Routes TCP/IP Administration Network Routing Information Network Routing Table Add Routes Destination ____________________________ Type _______ Gateway ____________________________ This line is used to provide abbreviated help on the currently selected field. CANCEL REFRESH ENTER CLEAR HELP Screen 3-13. Network Routing Table — Add Routes This screen is used to add network routes.
bbbbb System Administration b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb Use this screen as follows: 1. Type the destination, type, and gateway of the route to be added. Press Tab or use the arrow keys to move from field to field. 2. Press if you don’t want to add what you just typed, or press to enter the data. The Network Routing Information — Network Routing Table screen will reappear. CANCEL ENTER 3. Access this screen again and repeat steps 1 and 2 for each new route to be added.
bbbbb System Administration b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb bbbbbbbbbbbbbbb Brouter Administration Brouter Administration Port __ __ __ __ __ __ __ __ Client Name or IP Address _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ _________________________ Client Link __ __ __ __ __ __ __ __ Client Status ____________ ____________ ____________ ____________ _____
bbbbb System Administration b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb Field Name c Description bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb c c Port number used on the DEFINITY switch. Valid range is 1 to 12. Port c Each port can only be assigned once. bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb c c Client Name c Host name or IP address of the client machine authorized to or IP c connect to this port. (Network name of the adjunct.
bbbbb System Administration b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb Add Client Link Brouter Administration Add Client Port __ CANCEL REFRESH ENTER Client Name or IP Address ____________________ CLEAR Client Link _ HELP This screen is used to add client links. When you add a client link, after you press the ENTER function key, the previous screen (Brouter Administration) will appear with the cursor at the beginning of the new entry.
bbbbb System Administration b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb Field Name c Description bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb c c Client Link c Link number from 1 to 8, used by client when connecting to this c port if client has more than 1 logical link into the MFB. Default = 1. Use this screen as follows: 1. Type the port, client name, and number of the first client link you want to add. Press Tab or use the arrow keys to move from field to field. 2.
bbbbb System Administration b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb bbbbbbbbbbbbbbb Maintenance Maintenance 1. Removable Media Operations... 2. Set System Time and Date 3. Reset System... 4. System Logs 5. Security Logs... 6. Ping Host 7. Exit This line is used to provide abbreviated help on the currently selected field. EXIT REFRESH ENTER HELP Screen 3-15. Maintenance (Main Menu) c c c Removable Media c Provides access to the Removable Media Operations menu Operations...
bbbbb System Administration b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb Removable Media Operations Maintenance Removable Media Operations 1. Format Removable Media 2. Save Configuration Data To Removable Media 3. Restore Configuration Data From Removable Media 4. Exit This line is used to provide abbreviated help on the currently selected field. EXIT REFRESH ENTER HELP Screen 3-16.
bbbbb System Administration b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb Set System Time and Date Maintenance Set System Time and Date Month: __ Time: __:__ Day: __ Year: ____ Standard Timezone Information ST Name: __________ Offset Time: __:__ Direction (E/W): _ Daylight Savings Timezone Information DST Name: __________ This line is used to provide abbreviated help on the currently selected field. CANCEL REFRESH ENTER CLEAR HELP Screen 3-17.
bbbbb System Administration b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb c Description Name bField bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb c c Offset Time: c The number of hours that vary from Universal Time (also c known as Greenwich Mean Time). See the table that follows.
bbbbb System Administration b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb If you leave this field blank, or if you clear the offset time or direction, they will be supplied automatically from the preceding table. If you enter a name or abbreviation that is not in the table, then you must also enter offset time and direction.
bbbbb System Administration b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb Reset System Maintenance Reset System 1. Shutdown 2. Restart System 3. Reboot System 4. Exit This line is used to provide abbreviated help on the currently selected field. EXIT REFRESH ENTER HELP Screen 3-18. Reset System c Description Field Name bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb c c Shuts down the entire system.
bbbbb System Administration b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb 3. For Shutdown: The following message appears: THE SYSTEM IS BEING SHUT DOWN NOW!! When the procedure is complete, ‘‘Shut’’ is displayed on the LCD panel of the Multi-Function board. 4. For Restart System: When the procedure is complete, you will return to the Reset System menu. 5. For Reboot System: If you run this from the system console (ADMIN/PORT B), the login prompt will appear when the procedure is complete.
bbbbb System Administration b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb System Logs Time Maintenance System Logs Type Process Page XXXX of XXXX Description This line is used to provide abbreviated help on the currently selected field. CANCEL REFRESH NXTDAY PRVDAY HELP NXTPG PRVPG Screen 3-19. System Logs This screen displays up-to-the-minute information on system activity, including errors.
bbbbb System Administration b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb Security Logs Maintenance Security Logs 1. Login Attempt Log 2. Client Access Logs 3. DEFINITY LAN Gateway Reset Log 4. Command Logs 5. Exit This line is used to provide abbreviated help on the currently selected field. EXIT REFRESH ENTER HELP Screen 3-20.
bbbbb System Administration b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb Login Attempt Log Maintenance System Logs Login Attempt Log Date and Time CANCEL User REFRESH Page X of X Terminal Port HELP NXTPG PRVPG Screen 3-21.
bbbbb System Administration b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb Client Access Logs Maintenance Security Logs Client Access Logs Time Type CANCEL REFRESH Process NXTDAY Page XXXX of XXXX Description PRVDAY HELP NXTPG PRVPG Screen 3-22. Client Access Logs c Description Field Name bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb c c Month and day (MM/DD). Changes as you move among Date c c dates.
bbbbb System Administration b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb DEFINITY LAN Gateway Reset Log Maintenance Security Logs DEFINITY LAN Gateway Reset Log Time Date CANCEL Page XXXX of XXXX Description REFRESH HELP NXTPG PRVPG Screen 3-23.
bbbbb System Administration b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb Command Logs Maintenance Security Logs Command Logs Time User CANCEL REFRESH Page XXXX of XXXX Description NXTDAY PRVDAY HELP NXTPG PRVPG Screen 3-24.
bbbbb System Administration b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb Ping Host Maintenance Ping Host Host Name or IP Address: ____________________ Packet count: ___ Packet size: ___ This line is used to provide abbreviated help on the currently selected field. CANCEL REFRESH ENTER CLEAR HELP Screen 3-25. Ping Host This screen allows the user to test the connection between the DEFINITY LAN Gateway and any host.
bbbbb System Administration b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb bbbbbbbbbbbbbbb Port Status/Control Port Status/Control DEFINITY Port State ___________ ___________ ___________ ___________ ___________ ___________ ___________ ___________ Port __ __ __ __ __ __ __ __ TCP/IP Connection State ___________ ___________ ___________ ___________ ___________ ___________ ___________ ___________ Brouter Messages Service to State DEFINITY __________ ____ __________ ____ __________ ____ __________ ____ ____
bbbbb System Administration b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb c Description Field Name bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb c c CONNECTED DOWN The BRI port is c administered on the DEFINITY switch but c Layer 2 is not established. c c CONNECTED The BRI port is administered c on the DEFINITY switch and Layer 2 is c established. c c BUSIEDOUT The BRI port is administered c on the DEFINITY switch but has been c c busied out in the MLAPD driver on the c MFB.
bbbbb System Administration b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb c CLOSE WAIT The client has closed its TCP c connection. The MFB’s TCP is waiting for a c close. c c FIN WAIT 1 The MFB’s TCP connection is c initiating a close. c c CLOSING The MFB’s TCP has notified the c client’s TCP of its intent to close. It is now c awaiting acknowledgment. c c LAST ACK The client has closed its TCP c connection. The MFB has closed its TCP c connection and is now awaiting c c acknowledgement.
bbbbb System Administration b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb 3. The following prompt appears: Are You Sure? (Y/N?) . Type Y and press Return . The Port Status/Control screen will reappear, showing the changed state. If you type N and press immediately reappear. Return , the Port Status/Control screen will To close a port’s TCP connection: 1. Press Tab or use the arrow keys to move to the desired port. 2. Press DROP to close the port’s TCP connection.
bbbbb System Administration b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb bbbbbbbbbbbbbbb Message Collection Period Port Status/Control Message Collection Period Port: xx Client: yy Link: zz Period: ___ This line is used to provide abbreviated help on the currently selected field. CANCEL REFRESH ENTER CLEAR HELP Screen 3-27. Message Collection Period This screen enables you to set the message collection period for a port.
bbbbb System Administration b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb c Description Field Name bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb c c The port for which messages are to be collected. Port c Display-only. c bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb c c The client name or IP address for which messages are to be Client c collected. Display-only.
bbbbb b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb Maintenance 4 bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb b bbbbbb This chapter provides information for diagnosing, repairing, and maintaining the DEFINITY LAN Gateway system. The maintenance screens used in these tasks are located in Chapter 3. Repair Orientation This section gives basic information about the DEFINITY LAN Gateway system.
bbbbb Maintenance b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb bbbbbbbbbbbbbbb System Specifications Table 4-1 defines the basic specifications of the DEFINITY LAN Gateway system. bbbbbbbbbbbbbbbbbbbbbbbb Table 4-1. System Capacities, Requirements, and Limitations bb bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb c Physical Dimensions c Weight: 6.2 pounds c c Length: 14.75 inches c Height: 7.
bbbbb Maintenance b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb bbbbbbbbbbbbbbb bbbbbbbbbbbbbbbbbbbbb Physical Description Refer to Figure 4-1, DEFINITY LAN Gateway System Assembly, when reading this section. I2C bus cable SCSI bus cable Power cable Tie wrap Multi-Function board (TN2208) Alarm board (TN2170) Retaining pins Tape drive (without cover) ENTER / YES &T AT BACK NEXT / NO Disk drive SCSI bus cable Power supply bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb Figure 4-1.
bbbbb Maintenance b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb Four main items make up the DEFINITY LAN Gateway system hardware assembly shown in Figure 4-1. They are: TN2208 Multi-Function Board (MFB) — The main circuit board that holds the central processing unit, controllers, and memory devices that make the system operational. NOTE: The DEFINITY LAN Gateway batteries are not field-replaceable. If the batteries on the TN2208 are low, replace the the board.
bbbbb Maintenance b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb bbbbbbbbbbbbbbb System States The DEFINITY LAN Gateway system initializes, operates, shuts down, and is diagnosed and maintained in different states. These states are displayed on the faceplate panel LCD shown in Figure 4-2. bbbbbbbbbbbbbbbbbbbbb ENTER/YES BUTTON STATE OF OPERATION OR MENU SELECTION ALARM FLASHING HEARTBEAT BACK BUTTON NEXT/NO BUTTON bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb Figure 4-2.
bbbbb Maintenance b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb Table 4-2 gives a description of the alarms, indications, and states of the DEFINITY LAN Gateway system. bbbbbbbbbbbbbbbbbbbbbbbb Table 4-2.
bbbbb Maintenance b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb bbbbbbbbbbbbbbbbbbbbbbbb Table 4-2. System States (continued) AINIT c ASAI Initialization — Displayed when the DEFINITY LAN c Gateway software is initializing from boot. bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb c ASAI-Ethernet State — Displayed when the DEFINITY LAN ASAI-X c Gateway software is fully initialized and providing service, or c ready to provide service.
bbbbb Maintenance b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb bbbbbbbbbbbbbbbbbbbbbbbb Table 4-2. System States (continued) c faceplate panel LCD c 3. Read/Write functions — Lists byte-, word-, and longc address values. c c 4. Additional tests — Lists diagnostic tests. These are also c shown on the faceplate panel LCD c c 5. Automatic boot — Brings up the system from a shutdown c mode, showing initialization operations and tests. c 6.
bbbbb Maintenance b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb bbbbbbbbbbbbbbbbbbbbbbbb 486 DEAD RESET *MJ CMD *MJ BTEST (40 SECONDS) *MJ E SHUT *MJ E SHUT (FLASHING) *MF BOOT (10 SECONDS) *MJ M SHUT *MJ PGM386 OR: *MJ PGMFAC *MJ PGMALB *MJ M SHUT (FLASHING) (50 SECONDS) *MJ OSINIT (15 SECONDS) *MJ OS (50 SECS.
bbbbb Maintenance b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb bbbbbbbbbbbbbbb Maintenance Connections Common types of console terminals are used for both switch and local DEFINITY LAN Gateway maintenance, allowing the same baud rates and parity to be used. Although a local maintenance terminal is optional, it does need to be available for installation and troubleshooting. A remote maintenance terminal may also be used.
bbbbb Maintenance b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb bbbbbbbbbbbbbbbbbbbbbbbb (Not Used) Telnet Management Client 10BaseT ❶ (Twisted Pair) Balun Ethernet Coaxial Cable Switch Alarm Board ALB Cable DEFINITY LAN Gateway Client ❷ LAN Server RJ45 DEFINITY LAN Gateway Client ❷ Telnet Management Client LAN Server 10BaseT ❶ (Twisted Pair) TN2170 RS-232 10BaseT HUB ❸ Null Modem H600-258 G1 ❹ Modem T/R Modem Admin/Port B House Wiring Z3A4 MultiFunction Board MFB Y Cable Z3A1 Te
bbbbb Maintenance b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb Table 4-3, Maintenance Terminal Hookups, lists the general requirements of terminals hooked up locally or remotely. Always refer to the terminal and printer manuals that accompany each machine to make cable connections, set up option settings, and program function keys. bbbbbbbbbbbbbbbbbbbbbbbb Table 4-3.
bbbbb Maintenance b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb bbbbbbbbbbbbbbb Maintenance Login Procedure This is not a procedure. Please supply. If you cannot log in, first check terminal power, connections, settings, and modem speed if you are connected via a modem. If the modem appears to be locked up, type * @ ; this may fix the remote access problem. If you still cannot reach the DEFINITY LAN Gateway system, call the switch administrator.
bbbbb Maintenance b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb 3. Unsnap the two gang latches at the bottom front of the MFB and Alarm Board, and swing downward. Squeeze the boards together and slip off the spring clip. 4. Carefully slide the DEFINITY LAN Gateway system from the switch carrier. Handle with care; the system weighs 6.2 pounds. 5. Disconnect the Interboard bus cable from the top edge of both boards using the pull tab. 6.
bbbbb Maintenance b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb ! CAUTION: Check that backup tapes are not write-protected; the tab is positioned closest to the end of the cartridge (it will cover the deeper inset). On the generic tape, ensure that the tab remains in the write-protected position. bbbbbbbbbbbbbbb Replacing the Disk/Tape Drive To remove either the disk drive or the tape drive from the Alarm Board, refer back to Figure 4-1 and follow the steps below.
bbbbb Maintenance b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb 9. If either drive is to be replaced, the mounting bracket from the bottom of each will have to be removed and reattached to the drive. (Note the four screws which attach the bracket to the drive.) To mount either drive: 1. Ensure that the EMI shield is snapped into place across the tape drive. 2. First plug the power and SCSI bus cables into the drive. 3.
bbbbb Maintenance b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb bbbbbbbbbbbbbbb MT2ST/N50 Tape Drive The MT2ST/N50 3.5-inch SCSI tape drive is used on the DEFINITY LAN Gateway system. Figure 4-8 shows the jumper connections that select options to allow the drive to be accessed. bbbbbbbbbbbbbbbbbbbbb 1 2 49 50 1 S3 S2 S1 S0 2 3 4 Strap J1 Interface Connector (PCBA CL) RA1 (under) PCBA CL J2 Power Supply Connector (PCBA CL) bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb RA2 (under) Figure 4-8.
bbbbb b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb Appendix A: PBX Carrier Configuration Worksheets A bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb This appendix contains worksheets helpful in installing the DEFINITY LAN Gateway system. Worksheet A-1 is used to obtain an inventory of your present circuit pack arrangement in the PBX. Worksheet A-2 is for help in determining how to rearrange these circuit packs to ‘‘free up’’ five slots for the DEFINITY LAN Gateway system assembly.
bbbbb Appendix A: PBX Carrier Configuration Worksheets b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb b bbbbbb Worksheet A-1: Port Slot Assignments (Before Carrier Arrangement) Date ___________________________ Prepared By ___________________________ Contact Telephone Number ___________________________ Complete the following worksheet to indicate how circuit packs are currently arranged in the PBX carrier.
bbbbb b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb Appendix B: Supported Terminals and Modems/Option Settings B bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb This appendix contains: a worksheet for use in determining what terminals and modems you will use with the DEFINITY LAN Gateway system and information on option settings.
bbbbb Appendix B: Supported Terminals and Modems/Option Settings b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb b bbbbbb Worksheet B-1: Terminals/Modems Date ___________________________ Prepared By ___________________________ Contact Telephone Number ___________________________ To the AE: Complete this worksheet with the customer before configuring and ordering the DEFINITY LAN Gateway system.
bbbbb Appendix B: Supported Terminals and Modems/Option Settings b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb b bbbbbb Option Settings Set the options listed below to the corresponding setting for your terminal. Refer to the manual for your terminal for available options and the procedure to set them. bbbbbbbbbbbbbbbbbbbbb Table B-1.
bbbbb b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb Appendix C: Ordering Information C bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb bbbbbbbbbbbbbbbbbbbbbbbbb bbbbbb This appendix contains a list of Price Element Codes (PECs) and comcodes for primary and optional components comprising the DEFINITY LAN Gateway system. Complete System Table C-1.
bbbbb Appendix C: Ordering Information b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb bbbbbbbbbbbbbbbbbbbbbbbbb bbbbbb Primary Equipment Table C-2.
bbbbb Appendix C: Ordering Information b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb bbbbbbbbbbbbbbbbbbbbbbbb Table C-2.
bbbbb Appendix C: Ordering Information b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb bbbbbbbbbbbbbbbbbbbbbbbb Table C-2.
bbbbb Appendix C: Ordering Information b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb bbbbbbbbbbbbbbb Peripheral Equipment All peripherals are optional to the order. However, the customer must provide at least one terminal for system administration/maintenance. bbbbbbbbbbbbbbbbbbbbbbbb Table C-3.
bbbbb b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb Appendix D: Troubleshooting Procedures D bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb This appendix contains the following procedures: Bringing up the DEFINITY LAN Gateway System Solving Terminal Connection Problems Solving TCP/IP Connection Problems If these procedures do not solve the problem, contact the TSC.
bbbbb Appendix D: Troubleshooting Procedures b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb b bbbbbb Bringing up the DEFINITY LAN Gateway System Use the procedure below if you can’t get a login prompt. NOTE: ASAI must be enabled on the DEFINITY Customer Options form for the system to be fully operational. 1. First check terminal power, connections, settings, and modem speed if you are connected via a modem. If the modem appears to be locked up, type * @ ; this may fix the remote access problem. 2.
bbbbb Appendix D: Troubleshooting Procedures b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb b bbbbbb Solving Terminal Connection Problems To Be Supplied Issue 1 January 1996 D-3
bbbbb Appendix D: Troubleshooting Procedures b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb b bbbbbb Solving TCP/IP Connection Problems 1. If a client cannot connect to the DEFINITY LAN Gateway, check the Client Access Logs screen to see if any error messages appear related to that client. (Access the Main Menu screen and select Maintenance, then Security Logs, and then Client Access Logs.
bbbbb Appendix D: Troubleshooting Procedures b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb cannot successfully ping the gateway, contact your network administrator. 2. Ping another machine on the same network (or subnet) where the client resides. Be sure that this machine is up and running and is responding to pings from other machines on the same network (or subnet) as the DEFINITY LAN Gateway. If the DEFINITY LAN Gateway cannot successfully ping this machine, contact your network administrator. 3.
bbbbb b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb Appendix E: Sample Customer Configurations E bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb This appendix contains three examples of how a customer might configure a system using CallVisor ASAI over the DEFINITY LAN Gateway. It requires knowledge of TCP/IP networking. Example 1, Secure LAN with Defaults, shows a DEFINITY LAN Gateway system assembly already administered with default values and a client/server requiring administration.
bbbbb Appendix E: Sample Customer Configurations b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb b bbbbbb Example 1. Secure LAN with Defaults IP address = 192.170.10.1 IP address = 192.170.10.2 C1 C2 IP address = 192.170.10.100 DEFINITY LAN Default host name = definity Gateway System Default IP address = Assembly 192.168.25.10 Client/ Server Host name = client IP address = 192.168.25.
bbbbb Appendix E: Sample Customer Configurations b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb b bbbbbb Example 2. Secure LAN, No Defaults IP address = 192.170.10.1 IP address = 192.170.10.2 C1 C2 IP address = 192.170.10.100 Subnet mask = 255.255.255.0 DEFINITY LAN Host name = lgateserver Gateway IP address = 135.20.1.1 System Subnet mask = 255.255.255.0 Assembly Client/ Server Client name = lgateclient IP address = 135.20.1.2 Subnet mask = 255.255.255.
bbbbb Appendix E: Sample Customer Configurations b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb C. You will be on the Brouter Administration screen when done. Press EXIT to return to the Main Menu. 4. Reboot the system as follows. On the Main Menu, select Maintenance and then Reset System. When the Reset System screen appears, select Reboot System. Administer the Client/Server: 1. Administer the client host name ( lgateclient in this example), IP address (135.20.1.2 ) in this example, and subnet mask (255.
bbbbb Appendix E: Sample Customer Configurations b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb b bbbbbb Example 3. Multiple Secure LANs C3 IP address = 135.20.3.100 Subnet mask = 255.255.255.0 DEFINITY LAN Gateway System Assembly Host name = lgateserver IP address = 135.20.1.1 Subnet mask = 255.255.255.0 Default gateway = 135.20.1.100 (The route to 135.20.3 network is 135.20.1.200.) Host name = client 3 IP address = 135.20.3.1 Subnet mask = 255.255.255.0 Gateway 2 IP address = 135.20.1.
bbbbb Appendix E: Sample Customer Configurations b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb C. Access the Add Host screen again and do the same for clients 2 and 3 (C2 and C3). D. You will be on the Local Host Table screen when done. Exit the screen to return to the TCP/IP Administration Main Menu. 3. Administer the brouter as follows. On the Main Menu, select Brouter Administration. A. Delete the default entry. B. Press ADD to access the Add Client Link screen.
bbbbb Appendix E: Sample Customer Configurations b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb For this example, you would enter: DESTINATION 135.20.3 TYPE GATEWAY NETWORK 135.20.1.200 When you press ENTER , the Network Routing Table screen reappears. Exit until you reach the Main Menu. Administration of Each Client (C1, C2, and C3): 1. Administer the client name, IP address, and subnet mask (if not already done). 2.
bbbbb b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb Appendix F: Returning the Application to its Original State F bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb This appendix details how to return the system to its original state if it should crash. 1. Make sure the administrative/maintenance terminal is physically connected to Main/Port A on the TN2208. 2. Insert the original DEFINITY LAN Gateway tape that came with the system into the system assembly and close the lever. 3.
bbbbb Appendix F: Returning the Application to its Original State b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb 7. Type 2 and press Return . The following prompt appears: Enter Tape Device (0-6)(Default = 1) 8. Press Return . The following messages and menu appear: MFB Board Diagnostics PASSED Transferring To Software Copyright (c) 1992 AT&T All Rights Reserved 0: Exit 1: Initialize Disk 2: Modify Partition Map 3: Copy Generic Partitions 4: Additional Commands Enter option: 9.
bbbbb Appendix F: Returning the Application to its Original State b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb 11. Type 3 to copy file partitions. The following prompt appears: Enter SCSI ID of Disk (default 0): 12. Press Return to accept SCSI ID 0. A screen similar to the following appears: Copy generic data from tape to disk Changing partition size from 15624 to 40000. The login prompt appears when the restore procedure is complete.
bbbbb b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb Appendix G: Project Manager Worksheet G bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb This appendix contains a worksheet for the AT&T Project Manager to use to assist in the customer installation. The on-site system technician uses the networking information on this worksheet during installation.
bbbbb Appendix G: Project Manager Worksheet b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb b bbbbbb Worksheet G-1: Gather Networking Information Date ___________________________ Prepared By ___________________________ Contact Telephone Number ___________________________ The basic LAN addressing information you supply here will be used by the onsite systems technician during installation.
bbbbb b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb Glossary GL bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb Adjunct See Application. Application A process on a client computer that requests and receives ASAI services and capabilities through a program library or network service. The terms ‘‘application’’ and ‘‘adjunct’’ are sometimes used interchangeably. See also ASAI Application. ASAI Adjunct Switch Application Interface (ASAI). 1.
bbbbb Glossary b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb BRI Basic Rate Interface Bridge A router that connects two or more networks and forwards packets among them. Usually, bridges operate at the physical network level. For example, an Ethernet bridge connects two physical Ethernet cables and forwards from one cable to the other exactly those packets that are not local. Bridges differ from repeaters because bridges store and forward complete packets while repeaters forward electrical signals.
bbbbb Glossary b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb TCP Transport Connection Protocol TCP/IP Port A numbered access ‘‘subaddress’’ for an IP address that usually indicates the service or application that is desired to engage in a communications session.
bbbbb b b b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb Index 104A connecting block, 2-15 10BaseT Ethernet, 1-1 116A, 2-20 in DC-powered switch, 2-10 b bbbbbbbbbbbbbbbbb A Adapter faceplate, 2-13 Adapter cables, 2-7 Add Client Link screen, 3-33 Add Host screen, 3-20 Add Logins screen, 3-11 Add Routes screen, 3-29 Administration requirements, 1-1 Administration methods, 1-2 Administration/maintenance terminal, 2-17 ADUs, See Asynchronous Data Units Alarm Board, 2-10 Alarm board cables, 2-14 Alarm Board c
bbbbbb b b b b b b Index b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb DEFINITY LAN Gateway Reset Log screen, 3-46 Disk care of, 2-11 crash, 1-5, 2-7 b bbbbbbbbbbbbbbbbb E Equipment and safety considerations, 2-3 for use with DEFINITY LAN Gateway, 2-6 optional terminal, 2-7 Ethernet (10BaseT), 1-1 Ethernet transport, 1-1 Existing system upgrading, 1-5 External connections, 2-4 b bbbbbbbbbbbbbbbbb F Faceplate adapter, 2-13 Forms DEFINITY customer options, 2-3 Function keys, 3-3, 3-4 b bbbbbbbbbbbbbbbb
bbbbb b b b Index b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb b bbbbbbbbbbbbbbbbb b bbbbbbbbbbbbbbbbb N S Network Routing Daemon screen, 3-23 Network Routing Information (Main Menu) screen, 3-22 Network Routing Table screen, 3-27 Null modem, 2-10, 2-18 Safety considerations, 2-3 during installation, 2-1 SAT-PC, 2-17, See G3-MA Screens Add Client Link, 3-33 Add Host, 3-20 Add Logins, 3-11 Add Routes, 3-29 Brouter Administration, 3-31 Change Passwords, 3-13 Client Access Logs, 3-45 Command Logs, 3-47
bbbbb b b Index b bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb Multi-Function Board, 2-8 number required, 2-8 requirements, 2-2 Slot restrictions, 2-8 Software, 1-4 Solving terminal connection problems, D-3 Supported equipment, 2-6 Switch cycling power, 1-5, 2-8 DC-powered, 2-10 Switch carrier inserting system assembly in, 1-5, 2-7 System assembly, 1-2 hardware, 1-2 registering, 2-41 requirements, 2-2 security, 1-5 states, 2-13 upgrade, 1-5 System assembly, 1-1 connecting, 2-4 in carrier, 1-5, 2-7 insertin
