User guide

ManualsBrandsAT&T ManualsCordless Telephone900 MHz

Following a typical status SMS issued on request:

Short description

Detailed device application info

output released

remaining time to output off

measured voltage (analog mode input)

input open

clip mode and status

Main power failure detected

output inactive

output active, remaining time to disable could follow

output active and latched

reverse or pulse clip sequence in progress

input open, inactive

Building 1

door control unit

Out1:off

Out2: on 00:01:22

In 1 :3.14 V

In 2 :open

Clip:pulse on

Blackout

off

!on

open

Out 1 /2 status:

In 1 / 2 status:

Serial c

Before opening the unit disconnect

power supply and all live circuits

that may be connected.

ommunication port and

backup battery are located

inside the unit.

The front cover must be removed to

access the inside of the unit :

1. Push with two fingers on

top and bottom sides of

front cover to release it.

2. Pull the front cover and

keep it in a safe place.

The newer NiMH batteries are less harmful to the environment, have a longer life,

and contain recyclable materials. Recycling options available in your local area

should be considered when disposing of this product. Do not dispose of in fire.

The SIM card receptacle is intended for 3V SIM cards [GSM 11.12 phase 2+].

The SIM card must be inserted in the cardholder to put the unit into operation.

Make sure that there is no voltage applied to ATT-22.

Disconnect also the backup battery, if any. Following the figure below:

1. Unlock the top cover using

a small screwdriver.

2. Slide up the top lid.

3. Insert the SIM card in the

receptacle, contacts must be

on the bottom side.

To remove the SIM

card repeat operations

1 and 2, gently pull the

SIM card out.

Do not operate without top cover, once the

SIM card has been inserted replace the top

lid and then connect power supply.

ADVANCED CONFIGURATION, LOCAL CONTROL, TRACING AND OTHER

FEATURES ARE AVAILABLE THROUGH SERIAL COMMUNICATION LINK

Specific literature and software for PC running Microsoft Windows are

available in miniCD present in the package

Remove the front cover following the instructions to access the RJ45 8 pin

modular jack serial interface [P].

Link cable is provided in the package.

Communication: RS-232 (DCE)

300 ... 115200 bit/s

7/8 data bits, 1/2 stop bits, 1 parity bit, 10/11 bit char length

Software handshake, Hardware handshake

ATT-tool

®®

RJ45 PINOUT

1. GND

2. RTS

3. GND

4. CTS

5. GND

6. TxD

7. GND

8. RxD

DB9-5

DB9-7

DB9-8

DB9-3

DB9-2

ATT-81 is provided with a backup

battery installed to keep the device

working even during power failures.

Once the front cover has been

removed:

1. Clip the battery to available

connector. This connector

must be isolated when

operating without backup

battery.

2. Push the battery into

retainer lids located under

front cover.

3. Replace the front cover to

close the unit.

Use only NiMH rechargeable

batteries 8.4V or 9.6V type.

WHEN USING BATTERIES AND

ACCUMULATORS ADHERE TO

RELEVANT REGULATIONS

ACCESS INSIDE BACKUP BATTERY

FREE CLIP CONTROL ADVANCED CONFIGURATION

COM PORT

SIM CARD

Any registered user can control outputs by means of SMS.

Following default commands can be changed to any custom text using .

More details available on .

Set output 1 ON [3]

Set output 2 ON [3]

Reset output 1 OFF

Reset output 2 OFF

Set output 1 ON and LATCH (set again at further power on) [4]

Set output 2 ON and LATCH (set again at further power on) [4]

Status SMS request

Ringback request once command has been processed

Commands will be recognized both uppercase, lowercase and mixed, nested

within other text wherever placed inside the incoming SMS.

Multiple commands into same SMS are allowed.

[3] Specifying a time interval after the set command, outputs will be released

once set time has elapsed. If a power failure occurs, the remainig time is

missing, thus the output will be released. Commad syntax:

days

hours

minutes

[4] Specifying date/time after the set and latch command, outputs will be

released at specified expiry date/time. Output status will be recovered after

blackout providing the real time clock sync has been performed successfully.

day

month

year -

hours -

minutes -

Example:

turn ON output 1 for 8 hours and 30 minutes,

turn on and latch output 2 until April 25, 2006 12:30

send back a status SMS

turn ON output 2,

ATT-tool

“Advanced Manual”

S1ddhhmm dd

M1ddmmyyhhmm dd

00-99

00-23

00-59

01 -31

01-12

00 99

00 23

00 59

S1000830 M22504061230 D

s2 M1

text alien trailer

SMS CONTROL

STATUS SMS

Registered users can control outputs by means of simple (free) calls.Supervisors

can set different activation times and outputs behaviour issuing an SMS:

On time

Out1 ON time in reverse mode

Hold time in reverse mode

Out2 ON time in reverse mode

Time to answer in toggle mode

none, pulse, toggle, reverse,dtmf

Clip feature is disabled, nothing happens on incoming calls from registered users.

Selecting this mode, incoming voice (or fax) call from registered user will turn on

out 1 for the time set in . A data call will do the same on out 2.

Incoming voice (or fax) calls will toggle out 1 on to off or vice-versa, data calls will

do the same on out 2. A ringback will be issued only when an output is turned on.

If the user waits online, after the time specified in ATT-22 will answer,

playing a low tone after output release or four high tones after output activation.

No ringback will be issued in such case.

This mode involves both outputs. Any incoming call from registered users will start

a sequence: out 1 will be activated for the time specified in , after the delay

set in , out 2 will be activated for the time specified in .

ATT-22 will answer to incoming call from registered users that, after a short

welcome tone, can type the command code on the phone keyboard. Following

default commands can be changed to any custom one using .

Once all commands are issued, confirm

the execution typing (star) key.

Using (hash) key is possible to delete

everything and start from the beginning.

Correct commands will be confirmed by

a sequence of high tones. Wrong

commands will produce a long low tone.

+2,290,,,pulse,rev1,hold,rev2,answ,mode

pulse

rev1

hold

rev2

answ

mode

pulse

answ

rev1

hold rev2

01 - 60” default 3”

01 - 600” default 3”

01 - 60” default 3”

01 - 60” default 15”

NONE

PULSE (default)

TOGGLE

REVERSE

DTMF

ATT-tool

Using ATT-tool is possible to configure advanced features, either linking the unit

with local com port or issuing SMS in remote mode. Refer to ATT-tool help file or

Advanced Manual for detailed information. Most important advanced features:

Alerts following local events can be issued to Recipients (up to 100).

Up to 100 supervisors can be stored inside the unit.

Users can be stored into SIM card phonebook.

Conditional users (having more features) can be stored into device memory.

Remove any entry from phonebooks by means of ATT-tool or issuing an SMS.

Emails service configuration, available for GPRS devices.

Activities to be performed on a time basis (up to 100).

Add / edit Recipients (group 9)

Add / edit Supervisors (group 7)

Add / edit Users (group 0 / group 1)

Delete Phonebook entries

GPRS / Email settings

Scheduled operations

OUT1 ON

OUT1 OFF

OUT1 LATCH

CONFIRM

OUT2 ON

OUT2 OFF

OUT2 LATCH

STATUS

DELETE

Operating without SIM PIN

Enter default SIM PIN

0000

Change default SIM PIN

ATT-tool

WARNING

The simplest way is to put your SIM card into a cellular phone and

program it so it won't ask for the PIN. The SIM card is 'open' and

someone could steal the SIM card, use it and read the information inside.

ATT-22 comes with a default PIN = (four zeroes).

Put your SIM card into a cellular phone and program the PIN using the

given number.

Using com port and running on Microsoft® Windows®

PC you can modify the default PIN on both ATT-22 and SIM card.

If you insert a SIM card that asks for a PIN number different from

that stored into ATT-22, the device will not operate.

If you enter the PIN 3 times incorrectly, SIM card will lock up and you

must provide the PUK (PIN Unblocking Key).

Add Users (group 0)

Store first supervisor

ATT-22 deletes any pending SMS at power-on.

Remote control is allowed to registered users only.

It's possible to add, modify or delete subscribers

from the SIM card phonebook using any GSM

mobile phone or SIM card reader/writer.

Following operating instructions provided by

phone manufacturer insert the SIM card into the

SIM card holder, turn on the phone and scroll the

option menu to enter the SIM card Phonebook edit

mode.

Enter the users name and telephone number using international format.

Insert the SIM card into the device SIM card holder and turn on the power supply,

the unit is ready to operate.

Although it is not mandatory to store a supervisor, you may add a supervisor who

then has additional special commands only available to him (advanced manual).

To store the first supervisor, once the unit is operative, issue the following SMS:

start character

system PIN (default = 0000)

supervisor’s name to be stored

optional email address

end character

Example:

The telephone number of SMS sender is automatically collected from the

incoming call presentation (thus the telephone number must be kept visible) and

will be assumed as the first supervisor’s telephone number.

First supervisor will be stored at position 401 and the unit will send back a

confirmation or error SMS.

The dot [.] character is the separator between fields and must not be used inside

NAME field. It's possible to use dot characters inside Email field.

It’s possible to use both and @ characters before the domain name.

SMS delivery failure is usually less than 1% but you must keep in mind

that a message could not arrive and you cannot complain with your

operator for this.

#xxxx.Name.email*

xxxx

Name

#0000.Harry Potter.harry.potter@hogwarts.com*

4 CHARACTERS

14 CHARACTERS MAX

40 CHARACTERS MAX

To identify your device more easily, you can store some specific information.

A supervisor can issue the following SMS:

Device own phone number [1]

Short description

Optional device own email address [2]

Detailed device application info

Example:

and will be shown within status SMS sent by this unit.

[1] Device phone number (always in international format) will be used to perform

real time clock autosync, missing this field the real time clock is unreliable and

SMS commands involving date field will be rejected.

[2] All email issued from Gprs type unit will be sent carbon copy also to its own

mailbox if a a valid address is provided.

+3,300,tel,info,,,,,email,text

tel

info

text

+3,300,+4456789,Building 1,,,,,,Apt. 5 living room

info text

20 CHAR MAX

14 CHAR MAX

40 CHAR MAX

56 CHAR MAX

QUICK START

SIM PIN DEVICE INFO

SYSTEM COMMANDS

Special control SMS are reserved for supervisors only:

Disable free calls control feature (CLIP): incoming calls will be rejected.

Enable free calls control feature (CLIP): incoming calls from registered users will

activate outputs following the specified sequence.

An SMS reporting last # (1-9) answered call list will be sent. Full list specifying 0.

An SMS reporting last # (1-9) unanswered call list will be sent. 0 = full list.

An Email reporting the complete phonebook will be issued to supervisor’s email

address, if any (GPRS only).

An Email reporting the complete phonebook and all system settings will be issued

to supervisor’s email address, if any (GPRS only).

Stop

Start

Lista#

Listu#

Pbook

Pbook++

131211

987654

Standards Ref. ETS 300-342-1

Directive No. 1999/5/CE:

0678