5800_CIB_1ATT 8/6/02 10:43 AM Page II USER’S MANUAL Part 2 Expansion Handset 5800 Please also read Part 1 — Important Product Information © 2002 Advanced American Telephones. All Rights Reserved. AT&T and the Globe Symbol are trademarks of AT&T Corp., licensed to Advanced American Telephones.
5800_CIB_1ATT 8/6/02 10:43 AM Page III Visit us at www.telephones.att.com © 2002 Advanced American Telephones. All Rights Reserved. AT&T and the Globe Design are trademarks of AT&T Corp., licensed to Advanced American Telephones. Printed in China.
5800_CIB_1ATT 8/6/02 10:43 AM Page V BEFORE YOU BEGIN ......................................................................1 About Handset Registration ....................................................................................1 About Softkeys.........................................................................................................1 CHARGE THE BATTERY...................................................................2 REGISTER THE HANDSET........................................
5800_CIB_1ATT 8/6/02 10:43 AM Page 1 BEFORE YOU BEGIN • • • • You must register this (and any other) handset with the base, following the directions in “REGISTER THE HANDSET.” This handset is compatible with telephone models 5840 and 5830. The original handset that came with the base is automatically registered as Handset 1. Additional handsets will be assigned Handset 2, Handset 3, Handset 4, Handset 5, and Handset 6.
800_CIB_1ATT 8/6/02 10:43 AM Page 2 CHARGE THE BATTERY CHARGE THE BATTERY 1 Install the handset battery pack. Use only the battery supplied with this handset or AT&T Accessory Battery Model 2401, SKU#91077. • When you install the battery pack the first time, the handset will display ENTER BASE ID. 2 a) Remove battery compartment cover by pressing on indentation and sliding downward. b) Align the contacts and place the battery pack in the battery compartment.
5800_CIB_1ATT 8/6/02 10:43 AM Page 3 REGISTER THE HANDSET 1 Make sure to charge the handset battery pack at least 12 hours. 2 At the cordless handset, use the softkey to select NEW. 3 Enter the 15-digit Base Unit ID Code located on the underside of your Model 5830 base. 4 Use the softkey to select OK. The screen displays PLEASE WAIT!!. 5 After about 45 seconds, the screen displays FOUND BASE. If the handset displays BASE BUSY TRY LATER, the base is in use.
5800_CIB_1ATT 8/6/02 10:43 AM Page 4 INSTALLATION Belt Clip INSTALLATION Attach the belt clip (optional). a) Slide down into grooves to attach. b) Press tabs on belt clip into slots on back of handset to reattach. Headset You can use this telephone hands-free when you install any industry standard 2.5 mm headset (purchased separately). For best results use an AT&T 2.5 mm headset. Plug the headset into the jack located on the left side of the handset (under the small rubber flap).
5800_CIB_1ATT 8/6/02 10:43 AM Page 5 Battery Life A fully charged battery provides an average talk time of about eight hours, or standby time of five days. INSTALLATION Talk time and standby time may vary depending on ¥NOTE: operating conditions. Charge the Handset Battery Pack • • • After a low battery indicator, the handset battery needs to be charged. Place the handset in the base so the CHARGING light goes on. The battery pack is typically charged in nine hours.
Need Help Insert 8/6/02 8:25 AM Page 1 Congratulations on your purchase of this AT&T product. NEED HELP? Our representatives are here to help you with any questions concerning the operation of this product, available accessories, or any other related issues. Call Toll Free 1 (800) 360-4121 or visit our website at www.telephones.att.
