EN TABLE OF CONTENTS Table of Contents .............................................................................. 1 Getting started .................................................................................. 2 Handset registration ....................................................................... 3 Touch phone use and handling ...................................................... 4 Basic operation .................................................................................
EN GETTING STARTED The AT&T ID-282H Accessory Handset is for use with the AT&T ID-2820 Digital Cordless Telephone with Touch Sensitive Keypad. You must have the AT&T ID-2820 Digital Cordless Telephone with Touch Sensitive Keypad in order to use the AT&T ID-282H Accessory Handset. This manual only describes the steps necessary to set up the ID-282H Accessory Handset. Please read the manual for the ID-2820 Digital Cordless Telephone for detailed operating instructions.
1. Plug the AC Adapter cord into the base unit and then into a wall outlet. 2. Pull the battery contact tab out slowly and remove as shown. 3. Place the handset in the charging cradle. The battery icon on the display will flash and the base indicator light will turn on to show charging is in progress. Charge for at least 15 hours before registering the handset. Connect the charging cradle to a wall outlet Pull and remove battery contact tab USE ONLY CLASS 2 POWER SOURCE, Rated 6VDC, 400mA.
EN 3. Touch to confirm. 4. You will see the message: ‘REGISTERING...’. Press and hold the PAGE key on the cradle of the base unit. 5. ‘REGISTRATION ACCEPTED’ indicates that handset is registered. ‘RETRY?’ indicates that registration has failed. Touch to retry or to quit. NOTE : The base unit will then send a signal to the handset registering the handset to the base unit. Once the Registration function has been completed, the handset will return to Standby Mode.
EN BASIC OPERATION To adjust receiver / speakerphone volume: • Touch or during a call to raise or lower the volume. To make a call: 1. Touch and wait for a dial tone. 2. Enter destination phone number using numbers 0 - 9. If you make an to cancel. error, touch To answer a call: • Remove the handset from the base unit and touch . To redial the last number: then and wait for a dial tone. 1. Touch 2. Touch . To dial from the redial list: 1. Touch 2.
EN 3. The display will show 'DIAL' and 'DIAL 1+' options. Touch or to toggle between dialing a local call (DIAL) or a long distance call (DIAL 1+). Once you have selected the dialing option, press the key again. The number will be dialed as shown on the display. • DIAL: dials the number for a local call • DIAL 1+: dials the number for a long distance call To store a Caller ID number in Phonebook 1. Touch or to review the call log. The number of new and total calls will be displayed. 2.
to confirm and save record. NOTE: A number can be saved without entering a name. When requested to enter the name, press key and move to number entry. To dial from Phonebook 1. Touch 2. Touch 3. Touch . or to select the record you wish to dial. to dial. To program your voice mail access number: 1. Press the key.
EN To page from base to handset(s): 1. Press PAGE on the base unit . 2. All of the handsets registered to the base will beep and the display will show PAGING. 3. Once the handset is located, press to discontinue paging. Intercom call: 1. Touch . 2. Use and to select ‘INTERCOM CALL’ from the menu and touch and to select a handset and touch . 3. Use or dial the handset number you wish to call. To transfer a call between handsets: 1. Touch during a call. 2.
• The ID-282H may be used with any industry standard two-band 2.5mm headset, which must be purchased separately. Connect the headset to the jack located on the side of the handset. Your phone is now ready for headset use. You can purchase a suitable headset from AT&T or from any electronics retailer that sells phone equipment. Using the Room Monitor feature: To enable / disable the Room Monitor handset: 1. Touch 2. Use and select the Room Monitor menu or to select 'ON' / 'OFF'. to confirm. 3.
EN TROUBLESHOOTING See below for some common problems and their remedies. Whatever the problem, you should first check that: • The base unit is connected to the power supply and phone line. • The main power is switched on at the electrical outlet. • The handset battery is installed and has not run out of power. DO NOT attempt to make repairs yourself. This will void your warranty.
Handset does not ring Keys activated while talking • You must subscribe to Call Waiting Caller ID service through your local phone company for this feature to work. Contact your local phone company to confirm you have subscribed to for Call Waiting Caller ID service. • While receiving the Call Waiting call, a second line was also off hook.
EN Unable to make an intemal intercom call • Only one external call and one intermal intercom call can take place at once. Make sure no other handset is making a call. SAFETY INFORMATION Warning! AT&T DOES NOT represent this unit to be waterproof. To reduce the risk of fire, electrical shock, or damage to the unit, DO NOT expose this unit to rain or moisture. Observe the following safety precautions and warnings when setting up and using this product. 1. Read and understand all instructions. 2.
a) If liquid has been spilled onto the product. b) If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions because improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to normal operation. c) If the product has been exposed to rain or water. d) If the product has been dropped or the cabinet has been damaged.
EN 2. Do not dispose of the battery pack in a fire; the cells may explode. Do not expose battery pack to water. Dispose of old, defective battery packs in an environmentally - friendly manner in accordance with the relevant legislation. 3. Do not open or mutilate the battery pack. Released electrolyte is corrosive and may cause damage to the eyes or skin. The electrolyte may be toxic if swallowed. 4.
Handle the handset gently and carefully. Dropping it can damage circuit boards and cases and can cause it to malfunction. • Keep the handset away from excessive dust and dirt. Which can cause premature part wear. • Occasionally wipe the handset with a damp cloth to keep it looking new. Do not use harsh chemicals, cleaning solvents, or strong detergents.
EN SPECIFICATIONS TYPE DESCRIPTION Handset L x W x H 5.55 x 1.73 x 0.94 in Handset weight 4.41oz (with battery) Base L x W x H 3.68 x 3.13 x 1.50 in Base Weight 2.6 oz Standard Worldwide Digital Cordless Telecommunication (WDCT) Frequency range 2.4GHz ISM Channel bandwidth 1.729MHz Modulation GFSK Communication range Up to 984ft in open area Base power supply 120V / 60Hz Handset power supply 1 x NiMH 650mAh 3.
• • • • Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio / TV technician for help. CONSUMER CONSUMERINFORMATION INFORMATION a. This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA.
EN RENs on a telephone line may result in the devices not ringing in response to an incoming call. In most but not all areas, the sum of RENs should not exceed five (5.0). To be certain of the number of devices that may be connected to a line, as determined by the total RENs, contact the AT&T Customer Service Center. [For products approved after July 23, 2001, the REN for this product is part of the product identifier that has the format US: KT5W400BID2820.
k. Privacy of communications may not be ensured when using the phone. NOTICE: According to telephone company reports, AC electrical surges, typically resulting from lightning strikes, are very destructive to telephone equipment connected to AC power sources. To minimize damage from these types of surges, a surge arrestor is recommended. NOTICE TO HEARING AID WEARERS: This telephone has been registered with the FCC as hearing aid compatible.
EN transit to service facility. We do not warranty that the product will be compatible with any telephone equipment or systems or party lines. This warranty shall be void if the product is damaged as a result of defacement, misuse, abuse, neglect, accidents, destruction, or alteration of the serial number, improper electrical voltages or currents, repair, alteration or maintenance by any person or party other than AT&T’s authorized service facility or any violation of instructions furnished by AT&T.
Q&A WHAT DOES OUR WARRANTY COVER? • Any defect in material or workmanship. FOR HOW LONG AFTER THE ORIGINAL PURCHASE? • To the original purchaser only - ONE YEAR. WHAT WILL AT&T DO? • At our option, repair or replace your unit. HOW DO I SEND MY UNIT, IN OR OUT OF WARRANTY? • In the U.S., call AT&T Customer Service for Return Authorization at: 800-667-2118. • Properly pack your unit. Include any cables and accessories that were originally provided with the product.
EN • Products serviced by the owner or a service facility not expressly authorized by AT&T Communications. • Products purchased more than 12 months from current date. • Units purchased in “AS IS” condition, or units purchased as “Distressed Merchandise”. HOW DOES STATE LAW OR PROVINCIAL LAW RELATE TO THIS WARRANTY? • This warranty gives you specific rights. You may also have other rights that vary from state to state or province to province.
